Home › Drivetrain › A4R AUTOMATIC TRANSMISSION / TRANSAXLE › SHIFT LEVER › from 2015.08
RM19Y0E _52 Drivetrain _041457 A4R AUTOMATIC TRANSMISSION / TRANSAXLE _0197965 SHIFT LEVER G

A4R AUTOMATIC TRANSMISSION / TRANSAXLE  SHIFT LEVER  INSPECTION  


PROCEDURE

Hide 85933 1.INSPECT SHIFT LOCK CONTROL ECU

a.
C197449C03
1.188,0.958 0.385,1.292 true 1.188,1.281 0.583,1.698 true 2.219,1.792 1.844,1.365 true 2.219,0.948 3.063,1.271 true 2.219,1.302 2.729,1.708 true 0.104,0.063 0.635,0.448 0.531,0.385 10 *a 0.083,1.229 0.635,1.615 0.552,0.385 10 STP 0.417,1.646 0.938,2 0.521,0.354 10 IG 2.24,1.792 2.823,2.135 0.583,0.344 10 ACC 2.802,1.667 3.396,2.104 0.594,0.438 10 KLS+ 3.115,1.24 3.427,1.667 0.313,0.427 10 E
*a Component with harness connected
(Shift Lock Control ECU)


Measure the voltage according to the value(s) in the table below.

HINT:

Do not disconnect the shift lock control ECU connector.


Standard Voltage:
Tester Connection Condition Specified Condition
4 (STP) - 1 (E) Brake pedal depressed 11 to 14 V
Brake pedal released Below 1 V
5 (KLS+) - 1 (E) 1. Ignition switch ACC and shift lever in P Below 1 V
2. Ignition switch ACC and shift lever not in P
(Within approximately 1 second)
7.5 to 10.5 V
3. Ignition switch ACC and shift lever not in P
(After approximately 1 second)
6 to 9 V
6 (ACC) - 1 (E) Ignition switch ACC 11 to 14 V
Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
8 (IG) - 1 (E) Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V


If the result is not as specified and there are no problems with the wire harness, replace the shift lock control ECU.


b.

Measure the resistance according to the value(s) in the table below.

HINT:

Do not disconnect the shift lock control ECU connector.


Standard Resistance:
Tester Connection Condition Specified Condition
1 (E) - Body ground When battery voltage not applied Below 1 Ω


If the result is not as specified and there are no problems with the wire harness, replace the shift lock control ECU.


Hide 2.INSPECT TRANSMISSION CONTROL SWITCH

a.
C253241C03
1.969,1.021 2.313,0.823 true 1.677,1.01 1.365,0.75 true 1.948,1.344 2.156,1.646 true 2.365,0.729 3.021,1.188 0.656,0.458 10 false A/T3 1.063,0.594 1.667,0.99 0.604,0.396 10 false ATD 2.063,1.688 2.885,2.135 0.823,0.448 10 false NSSD 0.115,0.083 0.615,0.51 0.5,0.427 10 false *a
*a Component without harness connected
(Transmission Control Switch)


Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.

Standard Resistance:
Tester Connection Shift Lever Position Specified Condition
4 (NSSD) - 1 (A/T3) 2 and 3 Below 1 Ω
Except 2 and 3 10 kΩ or higher
4 (NSSD) - 2 (ATD) Except 2 and 3 Below 1 Ω
2 and 3 10 kΩ or higher


If the result is not as specified, replace the transmission floor shift assembly.


Hide 3.INSPECT SHIFT LOCK SOLENOID

a.
C197452C46
1.344,1.24 0.833,1.635 true 1.573,1.24 1.344,1.635 true 1.854,1.24 2.146,1.615 true 2.094,1.24 2.781,1.615 true 0.094,0.073 0.563,0.448 0.469,0.375 10 false *a 0.604,1.635 1.281,2.104 0.677,0.469 10 false SLS+ 1.219,1.667 1.979,2.146 0.76,0.479 10 false SLS- 2.063,1.635 2.615,2.104 0.552,0.469 10 false E2 2.833,1.625 3.302,2.083 0.469,0.458 10 false P
*a Component without harness connected
(Shift Lock Solenoid)


Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.

Standard Resistance:
Tester Connection Shift Lever Position Specified Condition
4 (P) - 3 (E2) P 10 kΩ or higher
Except P Below 1 Ω


If the result is not as specified, replace the transmission floor shift assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (SLS+) - 2 (SLS-) When battery voltage not applied 112 Ω


If the result is not as specified, replace the transmission floor shift assembly.