Home › Drivetrain › M5S MANUAL TRANSMISSION / TRANSAXLE › MANUAL TRANSMISSION UNIT › from 2015.08
RM19Y0E _52 Drivetrain _002985 M5S MANUAL TRANSMISSION / TRANSAXLE _0015106 MANUAL TRANSMISSION UNIT A

M5S MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSMISSION UNIT  DISASSEMBLY  


PROCEDURE

Hide 31111B 1.REMOVE CLUTCH HOUSING PLUG

a.

Remove the clutch housing plug from the clutch housing.


Hide 84210 2.REMOVE BACK-UP LIGHT SWITCH ASSEMBLY

a.
C318291E01
1.458,1.646 1.75,1.156 true 1.135,1.594 1.594,1.792 0.458,0.198 10 false SST

Using SST, remove the back-up light switch assembly.

SST
09224-00011  


Hide 33403S 3.REMOVE MTM SPEEDOMETER DRIVEN HOLE PLUG

C331642

a.

Remove the bolt and MTM speedometer driven hole plug from the extension(MTM) housing sub-assembly.


b.

Remove the O-ring from the MTM speedometer driven hole plug.


Hide 4.REMOVE FILLER PLUG

C222151

a.

Remove the filler plug and gasket from the extension(MTM) housing sub-assembly.


Hide 5.REMOVE DRAIN PLUG

a.
C222152

Remove the drain plug and gasket from the extension(MTM) housing sub-assembly.


Hide 33103 6.REMOVE EXTENSION(MTM) HOUSING SUB-ASSEMBLY

a.
C331643C01
2,0.844 2.573,0.552 true 1.885,1.438 2.51,1.656 true 2.594,0.438 2.823,0.646 0.229,0.208 10 false *1 2.573,1.583 2.802,1.792 0.229,0.208 10 false *2
*1 No. 1 Transmission Case Hanger
*2 Wire Harness Clamp Bracket


Remove the 6 bolts, No. 1 transmission case hanger and wire harness clamp bracket.


b.
C150555

Carefully tap the projection of the extension(MTM) housing sub-assembly.

NOTICE:

Do not damage the extension(MTM) housing sub-assembly.



Hide 33449B 7.REMOVE TRANSMISSION MAGNET

C150556

a.

Remove the transmission magnet from the manual transmission case.


Hide 33323 8.REMOVE OUTPUT SHAFT OIL SLINGER

C150557

a.

Remove the output shaft oil slinger from the manual transmission case.


Hide 33151 9.REMOVE OUTPUT SHAFT REAR BEARING(MTM) RETAINER

C150558

a.

Remove the 3 bolts and output shaft rear bearing(MTM) retainer.


Hide 33528B 10.REMOVE CONTROL SHAFT COVER

C341452

a.

Remove the 4 bolts, control shaft cover and gasket from the manual transmission case.


b.
C331644

Remove the 2 ring pins from the manual transmission case.

HINT:

It is not necessary to remove the ring pins unless they are being replaced.



Hide 33295A 11.REMOVE REVERSE RESTRICT SHAFT

C331648

a.

Remove the bolt and gasket.


b.
C331649

Remove the reverse restrict shaft, reverse restrict cam and spring from the manual transmission case.


Hide 33203 12.REMOVE NO. 1 SHIFT LEVER SHAFT SUB-ASSEMBLY

C331412

a.

Using a pin punch (5 mm) and hammer, remove the slotted spring pin.


b.

Remove the No. 1 shift lever shaft sub-assembly and No. 1 shift lever inner.


c.

Remove the boot from the manual transmission case.


Hide 33111 13.REMOVE MANUAL TRANSMISSION CASE

C150562

a.

Using a snap ring expander, remove the snap ring from the output shaft.


b.
C150563

Using a hexagon socket wrench (6 mm), remove the hexagon bolt of the reverse idler gear shaft and gasket.


c.
C331645C01
2.042,0.927 2.531,1.042 2.531,1.042 2.031,1.042 true 2.604,0.969 2.917,1.167 0.313,0.198 10 false *1
*1 Wire Harness Clamp Bracket


Remove the 8 bolts and 2 wire harness clamp brackets from the manual transmission case.


d.
C331646

Remove the 2 bolts from the clutch housing.


e.
C267832

Using a plastic-faced hammer, tap out the manual transmission case.

NOTICE:

Do not damage the manual transmission case.



Hide 33321 14.REMOVE OUTPUT SHAFT

a.
C150568

Remove the output shaft.


b.
C150570

Remove the input shaft bearing and the wave spring from the input shaft.


Hide 33176B 15.REMOVE TRANSMISSION OIL(MTM) SEPARATOR

a.
C321070

Remove the bolt and transmission oil(MTM) separator.


Hide 33244D 16.REMOVE NO. 3 GEAR SHIFT FORK SHAFT

C323046

a.

Remove the 3 bolts, gaskets, springs and balls from the clutch housing.


b.
C150572

Using a pin punch (5 mm) and hammer, remove the 2 slotted spring pins from the No. 3 gear shift fork shaft.


c.

Remove the No. 3 gear shift fork shaft, No. 3 gear shift fork and No. 3 gear shift head.


Hide 33242 17.REMOVE NO. 1 GEAR SHIFT FORK SHAFT

C150573

a.

Using a pin punch (5 mm) and hammer, remove the 2 slotted spring pins from the No. 1 gear shift fork shaft.


b.

Remove the No. 1 gear shift fork shaft, No. 1 gear shift fork and No. 1 gear shift head.


Hide 33243A 18.REMOVE NO. 2 GEAR SHIFT FORK SHAFT

C150574

a.

Using a pin punch (5 mm) and hammer, remove the 2 slotted spring pins from the No. 2 gear shift fork shaft.


b.

Remove the No. 2 gear shift fork shaft, No. 2 gear shift fork and No. 2 gear shift head.


Hide 33221 19.REMOVE REVERSE SHIFT ARM

C341453

a.

Remove the spring from the reverse shift arm.


b.
C150576

Remove the 3 bolts and reverse shift arm.


Hide 33266C 20.REMOVE SHIFT INTER LOCK PLATE

C150577

a.

Remove the 2 shift inter lock plates from the clutch housing.


Hide 33402 21.REMOVE REVERSE IDLER GEAR SUB-ASSEMBLY

C150578

a.

Remove the reverse idler gear sub-assembly, reverse idler gear thrust washer and reverse idler gear shaft from the clutch housing.


Hide 33326 22.REMOVE BEARING LOCK PLATE

C331650

a.

Remove the 3 bolts and bearing lock plate.


Hide 33311 23.REMOVE INPUT SHAFT

C150580

a.

Remove the input shaft and counter gear from the clutch housing.


Hide 33256 24.REMOVE SELECT INNER LEVER

C150581

a.

Using a pin punch (5 mm ) and hammer, remove the slotted spring pin.


b.

Remove the select lever shaft sub-assembly, select inner lever and spring.


c.
C150582

Using a screwdriver, remove the oil seal from the control shaft cover.

NOTICE:

Be careful not to damage the control shaft cover.



Hide 33111Q 25.REMOVE TRANSMISSION CASE OIL SEAL (CLUTCH HOUSING OIL SEAL)

C150583

a.

Using a screwdriver, remove the transmission case oil seal (clutch housing oil seal) from the clutch housing.

NOTICE:

Be careful not to damage the clutch housing.



Hide 33111Y 26.REMOVE TRANSMISSION CASE OIL SEAL

C150584

a.

Using a screwdriver and hammer, remove the transmission case oil seal from the manual transmission case.


Hide 33103R 27.REMOVE MANUAL TRANSMISSION EXTENSION HOUSING OIL SEAL

C150585

a.

Using a screwdriver, remove the manual transmission extension housing oil seal from the extension(MTM) housing sub-assembly.


Hide 33257B 28.REMOVE GEAR OIL PLATE

C150586

a.

Remove the bolt and gear oil plate from the extension(MTM) housing sub-assembly.