Home › Drivetrain › M5S MANUAL TRANSMISSION / TRANSAXLE › MANUAL TRANSMISSION UNIT › from 2015.08
RM19Y0E _52 Drivetrain _002985 M5S MANUAL TRANSMISSION / TRANSAXLE _0015106 MANUAL TRANSMISSION UNIT A

M5S MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSMISSION UNIT  REASSEMBLY  


PROCEDURE

Hide 33257B 1.INSTALL GEAR OIL PLATE

C150598

a.

Install the gear oil plate with the bolt to the extension(MTM) housing sub-assembly.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


Hide 33103R 2.INSTALL MANUAL TRANSMISSION EXTENSION HOUSING OIL SEAL

C150599N01
1.042,1.094 1.635,0.802 false 1.552,1.24 1.042,1.094 true 0.667,1.021 1.021,1.188 0.354,0.167 10 SST

a.

Using SST and a hammer, install a new manual transmission extension housing oil seal to the extension(MTM) housing sub-assembly.

SST
09950-60010  (09951-00540)
09950-70010  (09951-07150)

Drive in depth:

0 to -0.5 mm (0 to -0.020 in.)



b.

Coat the oil seal lip with MP grease.


Hide 33111Y 3.INSTALL TRANSMISSION CASE OIL SEAL

C150600N02
1.51,1.313 1.125,1.771 1.125,1.771 1.458,1.51 true 0.948,1.813 1.271,1.969 0.323,0.156 10 SST

a.

Using SST and a hammer, install a new transmission case oil seal to the manual transmission case.

SST
09950-60010  (09951-00300)
09950-70010  (09951-07150)

Protrusion :

3.9 to 4.7 mm (0.154 to 0.185 in.)



b.

Coat the oil seal lip with MP grease.


Hide 33111Q 4.INSTALL TRANSMISSION CASE OIL SEAL (CLUTCH HOUSING OIL SEAL)

C150601N02
1.417,0.865 0.802,0.781 0.802,0.781 1.406,1.406 true 0.479,0.688 0.792,0.854 0.313,0.167 10 SST

a.

Using SST and a hammer, install a new transmission case oil seal (clutch housing oil seal) to the clutch housing.

SST
09950-60010  (09951-00350)
09950-70010  (09951-07150)


b.

Coat the oil seal lip with MP grease.


Hide 33256 5.INSTALL SELECT INNER LEVER

C150602N02
1.818,0.941 2.169,1.125 0.351,0.184 10 SST 1.784,1.019 1.54,1.019 false

a.

Using SST and a hammer, install a new oil seal to the control shaft cover.

SST
09950-70010  (09951-07150)


b.

Coat the oil seal lip with MP grease.


c.
C150603

Install the select inner lever, select lever sub-assembly and spring to the control shaft cover.


d.

Using a pin punch (5 mm) and hammer, install a new slotted spring pin.

NOTICE:

Insert the slotted spring pin in the correct direction as shown in the illustration.



e.
C150604C01
1.906,1.229 1.333,1.698 true 2.135,0.688 2.677,0.469 true 2.698,0.365 2.948,0.563 0.25,0.198 10 *a 1.167,1.656 1.438,1.833 0.271,0.177 10 *b
*a Short
*b Long


Install the spring as shown in the illustration.


Hide 33311 6.INSTALL INPUT SHAFT

C150580

a.

Coat the sliding and rotating surfaces of the input shaft and counter gear with manual transmission gear oil.


b.

Install the input shaft and counter gear to the clutch housing.


Hide 33326 7.INSTALL BEARING LOCK PLATE

C331650

a.

Install the bearing lock plate with the 3 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 33402 8.INSTALL REVERSE IDLER GEAR SUB-ASSEMBLY

C150578

a.

Install the reverse idler gear sub-assembly, reverse idler gear thrust washer and reverse idler gear shaft to the clutch housing.


Hide 33266C 9.INSTALL SHIFT INTER LOCK PLATE

C150577

a.

Install the 2 shift inter lock plates to the clutch housing.


Hide 33221 10.INSTALL REVERSE SHIFT ARM

C150576

a.

Install the reverse shift arm with the 3 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


b.
C150605N02
2.156,1.115 1.781,0.583 true 2.094,1.396 1.396,1.938 true 1.667,0.396 1.865,0.573 0.198,0.177 10 A 1.25,1.938 1.448,2.115 0.198,0.177 10 B

Ensure that the pin moves smoothly between positions A (neutral position) and B (5th gear position) with the idler gear fully lowered.


c.
C341453

Install the spring to the reverse shift arm.


Hide 33243A 11.INSTALL NO. 2 GEAR SHIFT FORK SHAFT

a.

Distinguishing gear shift fork shafts

C331663C01
2.813,0.76 3.021,0.344 3.021,0.344 3.229,0.344 false 2.75,1.781 2.958,1.365 2.958,1.365 3.167,1.365 false 2.719,2.823 2.927,2.406 2.927,2.406 3.135,2.406 false 3.281,0.229 3.594,0.427 0.313,0.198 10 false *1 3.208,1.26 3.521,1.458 0.313,0.198 10 false *2 3.208,2.313 3.521,2.51 0.313,0.198 10 false *3
*1 No. 1 Gear Shift Fork *2 No. 2 Gear Shift Fork
*3 No. 3 Gear Shift Fork - -



b.

Install the No. 2 gear shift fork, No. 2 gear shift head and No. 2 gear shift fork shaft.


c.
C327155

Using a pin punch (5 mm) and hammer, install the 2 new slotted spring pins to the No. 2 gear shift fork shaft.


Hide 33242 12.INSTALL NO. 1 GEAR SHIFT FORK SHAFT

C327156

a.

Install the No. 1 gear shift fork, No. 1 gear shift head and No. 1 gear shift fork shaft.


b.

Using a pin punch (5 mm) and hammer, install the 2 new slotted spring pins to the No. 1 gear shift fork shaft.


Hide 33244D 13.INSTALL NO. 3 GEAR SHIFT FORK SHAFT

C327157

a.

Install the No. 3 gear shift fork, No. 3 gear shift head and No. 3 gear shift fork shaft.


b.

Using a pin punch (5 mm) and hammer, install the 2 new slotted spring pins to the No. 3 gear shift fork shaft.


c.
C323046C01
0.479,1.49 0.958,1.667 true 0.292,1.375 0.604,1.573 0.313,0.198 10 false *a
*a Green-colored spring


Install the 3 balls, springs and new gaskets to the clutch housing with the bolts.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


Hide 33176B 14.INSTALL TRANSMISSION OIL(MTM) SEPARATOR

a.
C321070

Install the transmission oil(MTM) separator with the bolt.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


Hide 33321 15.INSTALL OUTPUT SHAFT

C150570

a.

Coat the input shaft bearing with MP grease.


b.

Install the input shaft bearing and the wave spring to the input shaft.


c.
C150568

Install the output shaft onto the input shaft.


Hide 33111 16.INSTALL MANUAL TRANSMISSION CASE

C150606C01
3.115,2.052 3.271,2.052 false
V100143

FIPG


a.

Apply FIPG to the manual transmission case, as shown in the illustration.

FIPG:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


NOTICE:

Parts must be assembled within 10 minutes of application.

Otherwise, the packing (FIPG) material must be removed and reapplied.



b.
C331645C01
2.042,0.927 2.531,1.042 2.531,1.042 2.031,1.042 true 2.604,0.969 2.917,1.167 0.313,0.198 10 false *1
*1 Wire Harness Clamp Bracket


Install the manual transmission case and 2 wire harness clamp brackets with the 8 bolts.

Torque:
18.2 N*m (186 kgf*cm, 13 ft.*lbf)


c.
C331646

Install the 2 bolts to the clutch housing.

Torque:
18.2 N*m (186 kgf*cm, 13 ft.*lbf)


d.
C150562

Using a snap ring expander, install the snap ring to the output shaft.


e.
C150563

Using a hexagon socket wrench (6 mm), install a new gasket and the hexagon bolt to the reverse idler gear shaft.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


Hide 33203 17.INSTALL NO. 1 SHIFT LEVER SHAFT SUB-ASSEMBLY

C150607C01
3.104,2.042 3.26,2.042 false
V100144

MP grease


a.

Coat the No. 1 shift lever shaft sub-assembly with MP grease.


b.

Install the boot to the manual transmission case.


c.

Install the No. 1 shift lever shaft sub-assembly and No. 1 shift inner lever.


d.
C341454

Using a pin punch (5 mm) and hammer, install a new slotted spring pin to the No. 1 shift lever shaft sub-assembly.

NOTICE:

Insert the slotted spring pin in the correct direction as shown in the illustration.



Hide 33295A 18.INSTALL REVERSE RESTRICT SHAFT

C331649

a.

Install the spring, reverse restrict shaft and reverse restrict cam into the manual transmission case.


b.

Install the spring as shown in the illustration.


c.
C331648

Install a new gasket and bolt.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


Hide 33528B 19.INSTALL CONTROL SHAFT COVER

a.
C331644

Install the 2 ring pins onto the manual transmission case.

HINT:

It is not necessary to remove the ring pins unless they are being replaced.



b.
C341452

Install a new gasket and the control shaft cover with the 4 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 33151 20.INSTALL OUTPUT SHAFT REAR BEARING(MTM) RETAINER

C150558

a.

Install the output shaft rear bearing(MTM) retainer with the 3 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 33323 21.INSTALL OUTPUT SHAFT OIL SLINGER

C150557

a.

Install the output shaft oil slinger onto the manual transmission case.


Hide 33449B 22.INSTALL TRANSMISSION MAGNET

C150556

a.

Install the transmission magnet onto the manual transmission case.


Hide 33103 23.INSTALL EXTENSION(MTM) HOUSING SUB-ASSEMBLY

C331647C01
3.271,2.135 3.365,2.135 false
V100143

FIPG


a.

Apply FIPG to the extension(MTM) housing sub-assembly, as shown in the illustration.

FIPG:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


NOTICE:

Parts must be assembled within 10 minutes of application.

Otherwise, the packing (FIPG) material must be removed and reapplied.



b.
C331643C01
2,0.844 2.573,0.552 true 1.885,1.438 2.51,1.656 true 2.594,0.438 2.823,0.646 0.229,0.208 10 false *1 2.573,1.583 2.802,1.792 0.229,0.208 10 false *2
*1 No. 1 Transmission Case Hanger
*2 Wire Harness Clamp Bracket


Install the extension(MTM) housing sub-assembly, No. 1 transmission case hanger and wire harness clamp bracket with the 6 bolts.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


Hide 24.INSTALL DRAIN PLUG

C222152

a.

Install the drain plug and a new gasket to the extension(MTM) housing sub-assembly.

Torque:
39.2 N*m (400 kgf*cm, 29 ft.*lbf)


Hide 25.INSTALL FILLER PLUG

Install the filler plug and a new gasket to the extension(MTM) housing sub-assembly.

Torque:
39.2 N*m (400 kgf*cm, 29 ft.*lbf)

C222151

Hide 33403S 26.INSTALL MTM SPEEDOMETER DRIVEN HOLE PLUG

C331642

a.

Coat a new O-ring with manual transmission gear oil and install it to the MTM speedometer driven hole plug.


b.

Install the MTM speedometer driven hole plug with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 84210 27.INSTALL BACK-UP LIGHT SWITCH ASSEMBLY

a.
C321937C02
1.302,2.396 1.771,3.146 true 1.094,1.177 1.406,1.375 0.313,0.198 10 false *a 1.969,1.615 2.281,1.792 0.313,0.177 10 true *b 1.802,3.167 2.24,3.354 0.438,0.188 10 true SST
*a SST Fulcrum Length
*b Torque Wrench Fulcrum Length


Using SST, install the back-up light switch assembly and a new gasket to the manual transmission case.

SST
09224-00011  

Torque:
Specified tightening torque : 32 N*m (326 kgf*cm, 24 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 27.4 N*m (279 kgf*cm, 20 ft.*lbf)




b.

Connect the back-up light switch assembly connector to the wire bracket.


Hide 31111B 28.INSTALL CLUTCH HOUSING PLUG

a.

Install the clutch housing plug to the clutch housing.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)