Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › PROPELLER SHAFT ASSEMBLY › from 2015.08
RM19Y0E _52 Drivetrain _002986 DRIVE SHAFT / PROPELLER SHAFT _0015113 PROPELLER SHAFT ASSEMBLY A

DRIVE SHAFT / PROPELLER SHAFT  PROPELLER SHAFT ASSEMBLY  DISASSEMBLY  


PROCEDURE

Hide 1.INSPECT UNIVERSAL JOINT SPIDER ASSEMBLY

a.

Check that the joints move smoothly.


b.

Check the spider bearings for wear or damage.


c.

Check the spider bearing axial play by turning the yoke while holding the shaft tightly.

If necessary, replace the spider bearing.


Hide 37206 2.REMOVE CENTER SUPPORT BEARING BRACKET SUB-ASSEMBLY

a.
C331473

Remove the 2 bolts and center support bearing bracket sub-assembly from the No. 1 center support bearing.


Hide 3.REMOVE UNIVERSAL JOINT SPIDER ASSEMBLY

HINT:

Remove the universal joint spiders on the opposite side using the same procedure as below.


a.
C159161C01
1.979,1.021 2.313,0.583 2.313,0.583 2.083,1.042 false 2.302,0.396 2.823,0.917 0.521,0.521 10 *a
*a Matchmarks


Place matchmarks on the universal joint flange yoke and rear propeller shaft assembly.


b.
C159430

Using a brass bar and a hammer, slightly tap in the universal joint spider bearing.


c.

Using 2 screwdrivers, remove the 4 snap rings from the grooves.


d.

Hold the rear propeller shaft assembly in a vise between aluminium plates.

NOTICE:

Do not overtighten the vise.



e.
C115684N01
2.458,1.125 2.979,0.323 true 1.094,0.844 0.583,0.729 true 3.021,0.094 3.427,0.74 0.406,0.646 10 (A) 0.26,0.635 0.927,1.094 0.667,0.458 10 SST

Using SST, push out the universal joint spider bearing from the rear propeller shaft assembly.

SST
09332-25010  

HINT:

Sufficiently raise the part indicated by (A) so that it does not come into contact with the universal joint spider bearing.



f.
C115685C01
2.344,0.708 2.708,1.115 true 2.688,1.146 3.219,1.677 0.531,0.531 10 *a
*a Hammering Point


Clamp the universal joint spider bearing in a vise between aluminium plates and tap off the rear propeller shaft assembly with a hammer.

NOTICE:
·

Do not overtighten the vise.

·

Do not tap the propeller shaft tube.



HINT:

Remove the universal joint spider bearing on the opposite side using the same procedure.



g.

Remove the universal joint flange yoke with universal joint spider bearing from the rear propeller shaft assembly.


h.
C115686N01
0.885,1.042 0.583,1.042 false 2.563,1.125 3.042,0.302 true 0.24,0.938 1.01,1.438 0.771,0.5 10 SST 3.042,0.115 3.417,0.667 0.375,0.552 10 (A)

Reinstall the 2 removed universal joint spider bearings to the universal joint spider assembly and hold the universal joint spider assembly in a vise between aluminium plates.

NOTICE:

Do not overtighten the vise.



i.

Using SST, push out the universal joint spider bearing from the universal joint flange yoke.

SST
09332-25010  

HINT:

Sufficiently raise the part indicated by (A) so that it does not come into contact with the universal joint spider bearing.



j.
C115687C01
2.438,0.594 1.771,0.354 true 1.552,0.198 2.135,0.646 0.583,0.448 10 *a
*a Hammering Point


Clamp the universal joint spider bearing in a vise between aluminium plates and tap off the universal joint flange yoke with a hammer.

NOTICE:
·

Do not overtighten the vise.

·

Do not damage the universal joint flange yoke.



HINT:

Remove the universal joint spider bearing on the opposite side using the same procedure.



k.

Remove the universal joint spider assembly from the universal joint flange yoke.


Hide 37230 4.REMOVE NO. 1 CENTER SUPPORT BEARING ASSEMBLY

a.

Hold the front propeller shaft assembly in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.
C152580

Using SST and a hammer, release the staked part of the nut.

SST
09930-00010  

NOTICE:

Completely unstake the staked part before removing the lock nut.



c.

Remove the lock nut.


d.
C152581C01
1.698,1.125 0.656,1.781 0.656,1.781 1.698,1.344 true 0.448,1.698 1.135,2.135 0.688,0.438 10 *a
*a Matchmarks


Place matchmarks on the center universal joint yoke sub-assembly and front propeller shaft assembly.


e.
C152582C01
1.083,1.323 0.688,1.594 false 2.198,1.375 2.458,1.573 false 0.354,1.563 1.313,2.115 0.958,0.552 10 SST 2.448,1.625 3.292,2.094 0.844,0.469 10 SST 3.01,1.229 3.365,1.604 0.354,0.375 10 *b 1.438,1.865 2.021,2.167 0.583,0.302 10 *a
*a Hold
*b Turn


Using SST, remove the center universal joint yoke sub-assembly.

SST
09950-00020  
09950-00030  

NOTICE:

Apply grease to the threads and end of the SST center bolt before use.



f.

Remove the washer and No. 1 center support bearing assembly from the front propeller shaft assembly.