Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM › from 2015.08
RM19Y0E _58 Vehicle Interior _003006 THEFT DETERRENT / KEYLESS ENTRY _0015195 THEFT DETERRENT SYSTEM D

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  SYSTEM DESCRIPTION  


OUTLINE OF THEFT DETERRENT SYSTEM


w/o Theft Warning ECU Assembly
·

The theft deterrent system can be set by locking the doors using the transmitter.

·

The alarm function will be activated when someone attempts to forcibly unlock any of the doors or open any of the doors, engine hood, and back door while the system is in the armed state.

·

In the alarm sounding state, the system flashes the hazard warning lights. At the same time, the system sounds the vehicle horn to deter break-in and theft as well as to warn people around the vehicle.

·

The alarm can be cancelled by locking/unlocking the doors using the transmitter or turning the ignition switch to ON.

·

The theft deterrent system has the active arming mode. There are 3 states; a disarmed state, an armed state, and an alarm sounding state.


w/ Theft Warning ECU Assembly
·

The theft deterrent system can be set by locking the doors using the transmitter.

·

The alarm function will be activated when someone attempts to forcibly unlock any of the doors or open any of the doors, engine hood, and back door, or if the intrusion sensor detects an intrusion into the cabin while the system is in the armed state.

·

In the alarm sounding state, the system flashes the hazard warning lights. At the same time, the system sounds the security buzzer to deter break-in and theft as well as to warn people around the vehicle.

·

The alarm can be cancelled by locking/unlocking the doors using the transmitter or starting the engine when all the doors and the engine hood are closed.

·

The theft deterrent system has the active arming mode. There are 4 states; a disarmed state, an arming preparation state, an armed state, and an alarm sounding state.


a.

Disarmed state:

·

The alarm function is not operating.

·

The theft deterrent system is not operating.



b.

Arming preparation state (w/ Theft Warning ECU Assembly):

·

The time until the system goes into the armed state.

·

The theft deterrent system is not operating.



c.

Armed state:

·

The theft deterrent system is operating.



d.

Alarm sounding state:

·

The alarm function is operating.


Alarm time:

Approximately 30 seconds.


Alarm Method and Time (w/o Theft Warning ECU Assembly)
Alarm Method Hazard Warning Lights Flashing
Map Light Assembly
No. 2 Room Light Assembly
Illuminate
Vehicle Horn Sounding
(approximately 0.5 second intervals)
Alarm Time Approximately 30 seconds

Alarm Method and Time (w/ Theft Warning ECU Assembly)
Alarm Method Hazard Warning Lights Flashing
Map Light Assembly
No. 2 Room Light Assembly
Illuminate
Security Buzzer Sounding
(approximately 0.5 second intervals)
Alarm Time Approximately 30 seconds



FUNCTION OF MAIN COMPONENTS


Component Function
Security indicator light Informs driver of theft deterrent system status.
Security buzzer*1 Sounds when attempted break-in or theft is detected.
Low pitched horn*2
High pitched horn*2
Sound when attempted break-in or theft is detected.
Hazard warning lights Flash when attempted break-in or theft is detected.
Map light assembly
No. 2 Room light assembly
Illuminates when attempted break-in or theft is detected.
Intrusion sensor*1 Sends signal to theft warning ECU assembly to sound alarm when detecting intrusion.
Door courtesy light switch Detects door status (open or closed).
Engine hood switch Detects engine hood status (open or closed).
Back door courtesy switch Detects back door status (open or closed).
Ignition or starter switch assembly Detects ignition switch status (off or on).
Unlock warning switch Detects ignition key status (insert or not).
Main body ECU (Fuse block assembly) Receives wireless door lock/unlock signal.

*1: w/ Theft Warning ECU Assembly

*2: w/o Theft Warning ECU Assembly



ACTIVE ARMING MODE


HINT:
·

Active arming mode starts the alarm control immediately after the doors are locked.

·

The term "doors" used in the text refers to the driver side door, front passenger side door, rear RH side door, rear LH side door and back door.



a.

Active arming mode:

This system operates as described in the diagram below when one of the items for each condition is met.

w/o Theft Warning ECU Assembly
B298502E02
3.125,0.635 4.5,1.25 1.375,0.615 10 Disarmed State 3.229,1.938 4.563,2.406 1.333,0.469 10 Armed State 2.938,3.25 4.656,3.729 1.719,0.479 10 Alarm Sounding State 0.844,2.958 2.156,3.531 1.313,0.573 10 Condition [3] 0.844,1.667 2.115,2.26 1.271,0.594 10 Condition [3] 2.906,2.583 4.031,3.104 1.125,0.521 10 Condition [4] 4.542,2.573 5.813,3.115 1.271,0.542 10 Condition [2] 3.74,1.281 4.896,1.76 1.156,0.479 10 Condition [1]

Condition Item
Condition [1] In the disarmed state, when the key is not inserted into the ignition key cylinder, the system state changes if the following condition is met.
·

With all doors and engine hood closed, lock all doors by wireless operation.


HINT:

If the doors are unlocked again by wireless operation, the doors will be locked after 30 seconds due to the automatic lock function and the system will change to the armed state.


Condition [2]
·

The engine hood is opened when the engine hood is closed.

·

Any door is opened when all doors are closed.*1

·

Driver side or front passenger side door is opened when all doors are closed.*2


HINT:

If any passenger door or the back door is opened, horns sound 5 seconds after the door is opened. The hazard warning lights, interior lights and security indicator illuminate or blink immediately when the door is opened. Horns sound immediately if the engine hood is opened.


Condition [3]
·

All doors are unlocked by wireless operation.

·

The ignition switch is turned to ON.


Condition [4] All doors are locked by wireless operation.
HINT:

After approximately 30 seconds, interior lights transfer to delay control. And if all doors and engine hood are closed for 1 second, door lock signal is output and system returns to armed state.




*1: w/ Rear Door Courtesy Light Switch

*2: w/o Rear Door Courtesy Light Switch


w/ Theft Warning ECU Assembly
B393761E01
3.115,0.406 4.979,0.865 1.865,0.458 10 false Disarmed State 2.802,1.969 4.667,2.427 1.865,0.458 10 false Arming Preparation State 3.219,3.583 5.083,4.042 1.865,0.458 10 false Armed State 2.948,5.156 4.813,5.615 1.865,0.458 10 false Alarm Sounding State 3.667,2.833 5.531,3.292 1.865,0.458 10 false Condition [2] 4.448,1.281 6.313,1.74 1.865,0.458 10 false Condition [1] 2.844,1.281 4.708,1.74 1.865,0.458 10 false Condition [3] 6,3.656 7.042,4.167 1.042,0.51 10 false Condition [1] 4.49,4.417 6.354,4.875 1.865,0.458 10 false Condition [4] 2.875,4.646 4.74,5.104 1.865,0.458 10 false Condition [1] 0.625,4.99 2.49,5.448 1.865,0.458 10 false Condition [5] 0.625,3.375 2.49,3.833 1.865,0.458 10 false Condition [5] 2.875,4.208 4.74,4.667 1.865,0.458 10 false Condition [6]

Condition Item
Condition [1] In the disarmed state, when the key is not inserted into the ignition key cylinder, the system state changes if the following condition is met.
·

With all doors and engine hood closed, lock all doors by wireless operation.


HINT:

If the doors are unlocked again by wireless operation, the doors will be locked after 40 seconds due to the automatic lock function and the system will change to the armed state.


Condition [2] Allow approximately 30 seconds to elapse.
Condition [3] When any of the following conditions is met:
·

All doors are unlocked by wireless operation.

·

Any door is opened.

·

The battery is reconnected.

·

The key is inserted in the ignition key cylinder.

·

The ignition switch is turned from off to ON.


Condition [4] When any of the following conditions is met:
·

Any door is opened when all doors are closed.

·

The engine hood is opened when the engine hood is closed.

·

The wire harness of theft deterrent system circuit is cut.

·

Turn ignition switch from off to on when key is not inserted into ignition key cylinder.

·

Intrusion sensor detects movement within vehicle when intrusion sensor is activated.

·

Interrupt the battery.


Condition [5]
·

All doors are unlocked by wireless operation.

·

The ignition switch is turned to ON and the engine runs approximately 2 seconds.


Condition [6] After approximately 30 sec. (10 times), alarm stops and system returns to armed state.




SECURITY INDICATOR LIGHT OUTPUT


a.

The main body ECU (fuse block assembly) outputs a signal to light up the security indicator, according to the state of the theft deterrent system. However, some of the actual lighting conditions of the security indicator are different from the output signals of the main body ECU (fuse block assembly).

Output
State of Theft Deterrent System Security Indicator light
Output Signal from Main Body ECU (Fuse Block Assembly) Actual Lighting Condition
Disarmed state (1), (2) OFF OFF
OFF (Immobiliser system unset)*1
BLINKING (Immobiliser system set)*1
Arming preparation state*2 ON ON
Armed state OFF BLINKING
Alarm sounding state ON ON

*1: w/ Engine Immobiliser System

*2: w/ Theft Warning ECU Assembly


Blinking Cycle
Time Security Indicator light
0.2 seconds. ON
1.8 seconds. OFF



ALARM MEMORY FUNCTION


a.

If there is any record of alarm set-off occurrences in the ECU memory, the system initiates the alarm memory function when the key is inserted in the ignition switch and turned to ON. In alarm memory function, the indicator light assembly (security indicator light) blinks the alert count at 1 second intervals (16 max.).

i.

When the ignition switch is turned to ON, the system outputs the alarm memory signal to the indicator light assembly (security indicator light). Three seconds after the alarm memory signal stops, the system outputs the diagnosis signal of the immobiliser system to the security indicator.


ii.

The alarm memory is deleted when the indicator light assembly (security indicator light) stops blinking or the ignition switch is turned off.