Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM › from 2015.08
RM19Y0E _58 Vehicle Interior _003006 THEFT DETERRENT / KEYLESS ENTRY _0015195 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  ECU Power Source Circuit  


DESCRIPTION

This circuit provides power for main body ECU (fuse block assembly) and theft warning ECU assembly* operation.

*: w/ Theft Warning ECU assembly


WIRING DIAGRAM

B419129E01
4.073,5.313 6.771,5.76 2.698,0.448 10 false Main Body ECU (Fuse Block Assembly) 5.125,2.958 5.771,3.292 0.646,0.333 10 false STOP 5.198,3.344 5.844,3.677 0.646,0.333 10 false D/L 5.115,3.729 5.76,4.063 0.646,0.333 10 false DOME 5.792,2.802 6.438,3.135 0.646,0.333 10 false STPB 4.354,2.448 5,2.781 0.646,0.333 10 false ECU-B 5.542,0.49 6.188,0.823 0.646,0.333 10 false +B 5.531,1.073 6.177,1.406 0.646,0.333 10 false GND 5.792,3.927 6.438,4.26 0.646,0.333 10 false E11 5.792,3.594 6.438,3.927 0.646,0.333 10 false DOM 5.792,3.198 6.438,3.531 0.646,0.333 10 false DLB 5.792,4.354 6.438,4.688 0.646,0.333 10 false E12 5.802,4.792 6.448,5.125 0.646,0.333 10 false E01 1.063,2.792 2.208,3.167 1.146,0.375 10 false from Battery 5.271,0.385 5.917,0.719 0.646,0.333 10 false 3 5.271,0.969 5.917,1.302 0.646,0.333 10 false 1 3.531,2.813 4.021,3.104 0.49,0.292 10 false 3A 4.177,1.99 4.667,2.281 0.49,0.292 10 false 3H 3.531,3.938 4.021,4.229 0.49,0.292 10 false 3G 3.531,4.344 4.021,4.635 0.49,0.292 10 false 3G 3.531,4.781 4.021,5.073 0.49,0.292 10 false 3G 4.323,1.781 4.969,2.115 0.646,0.333 10 false 3 3.583,2.615 4.229,2.948 0.646,0.333 10 false 1 3.573,3.74 4.219,4.073 0.646,0.333 10 false 1 3.542,4.156 4.188,4.49 0.646,0.333 10 false 11 3.531,4.594 4.177,4.927 0.646,0.333 10 false 12 5.125,1.667 7.156,2.146 2.031,0.479 10 false Theft Warning ECU Assembly* 4.365,1.156 5.01,1.49 0.646,0.333 10 false * 0.302,5.427 2.854,5.823 2.552,0.396 10 false *: w/ Theft Warning ECU Assembly 5.135,1.5 5.781,1.833 0.646,0.333 10 false J12

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BATTERY - MAIN BODY ECU (FUSE BLOCK ASSEMBLY) AND BODY GROUND)
a.

Disconnect the 3A, 3H and 3G main body ECU (fuse block assembly) connectors.


b.

Measure the voltage and resistance according to the value(s) in the table below.

B419130C01
0.75,0.5 1.167,0.75 0.417,0.25 2.865,0.5 3.281,0.75 0.417,0.25 5.417,0.5 5.833,0.75 0.417,0.25 0.865,0.542 1.281,0.865 0.417,0.323 10 false 3A 2.99,0.542 3.406,0.865 0.417,0.323 10 false 3H 5.542,0.552 5.958,0.875 0.417,0.323 10 false 3G 0.24,0.115 0.656,0.438 0.417,0.323 10 false *a
*a Front view of wire harness connector
to Main Body ECU (Fuse Block Assembly)
- -


Standard Voltage:
Tester Connection Condition Specified Condition
3A-1 - Body ground Always 11 to 14 V
3H-4 - Body ground Always 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
3G-1 - Body ground Always Below 1 Ω
3G-11 - Body ground Always Below 1 Ω
3G-12 - Body ground Always Below 1 Ω


Result:
Result Proceed to
OK (w/ Theft Warning ECU) A
OK (w/o Theft Warning ECU) B
NG C




A

2.CHECK HARNESS AND CONNECTOR (BATTERY - THEFT WARNING ECU ASSEMBKY AND BODY GROUND)

B

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (BATTERY - THEFT WARNING ECU ASSEMBKY AND BODY GROUND)
a.

Disconnect the J12 theft warning ECU assembly connector.


b.
B298942C01
1.5,0.125 1.99,0.417 0.49,0.292 1.26,1.333 1.063,1.948 true 1.729,1.354 1.927,1.969 true 1.625,0.188 2.135,0.51 0.51,0.323 10 J12 0.917,1.979 1.438,2.177 0.521,0.198 10 GND 1.865,1.979 2.333,2.177 0.469,0.198 10 +B 0.229,0.177 0.604,0.563 0.375,0.385 10 *a
*a Front view of wire harness connector
(to Theft Warning ECU Assembly)


Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
J12-3 (+B) - Body ground Always 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
J12-1 (GND) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR