Home › Power Source / Network › 2NR-VE BATTERY / CHARGING › GENERATOR › from 2015.08
RM19Y0E _57 Power Source / Network _041459 2NR-VE BATTERY / CHARGING _0192574 GENERATOR A

2NR-VE BATTERY / CHARGING  GENERATOR  DISASSEMBLY  


PROCEDURE

Hide 1.REMOVE GENERATOR PULLEY

a.
A363374C01
2.5,1.26 2.927,0.75 true 2.969,1.542 3.083,0.635 true 1.833,1.802 2.146,2 0.313,0.198 10 false *a 1.25,1.458 1.563,1.656 0.313,0.198 10 false *b 2.729,1.552 3.271,1.76 0.542,0.208 10 false SST1-A 2.198,1.302 2.74,1.51 0.542,0.208 10 false SST1-B
*a Hold
*b Turn


Clamp the generator housing stay in a vise tightly.


b.

Hold SST 1-A with a torque wrench, and tighten SST 1-B clockwise with the specified torque.

SST
09820-63011  (09820-06010, 09820-06021)

Item Part No.
SST 1-A and B 09820-06010
SST 2 09820-06021

Torque:
39 N*m (400 kgf*cm, 29 ft.*lbf)

NOTICE:

Check that SST is securely fitted onto the generator rotor shaft.



c.
A363375N01
2.781,0.781 2.406,0.396 false 2.021,0.302 2.635,0.5 0.615,0.198 10 false SST2

Insert SST2, and engage SST2 to the generator pulley nut.


d.
A363376C01
1.917,0.927 2.521,0.667 true 3.021,1.542 3.031,0.927 true 1.292,2.688 1.604,2.885 0.313,0.198 10 false *a 2.146,2.885 2.458,3.083 0.313,0.198 10 false *b 1.542,0.854 2.104,1.073 0.563,0.219 10 false SST2 2.781,1.552 3.396,1.802 0.615,0.25 10 false SST1-A
*a Hold
*b Turn


To loosen the generator pulley nut, turn SST1-A in the direction shown in the illustration.

NOTICE:

To prevent damage to the rotor shaft, do not loosen the generator pulley nut by more than one half turn.



e.

Remove SST2 from the generator assembly.


f.
A363377C01
2.531,1.156 2.927,0.76 true 3.063,1.385 3.115,0.656 true 2.198,1.458 2.51,1.656 0.313,0.198 10 false *a 1.563,1.375 1.875,1.573 0.313,0.198 10 false *b 2.313,1.177 2.917,1.406 0.604,0.229 10 false SST1-B 2.802,1.406 3.406,1.635 0.604,0.229 10 false SST1-A
*a Hold
*b Turn


Hold SST1-A, Turn SST1-B, and remove SST1-A and SST1-B in the direction shown in the illustration.


g.

Remove the generator pulley nut and generator pulley.


h.

Remove the generator assembly from a vise.


Hide 2.REMOVE GENERATOR REAR END COVER

a.
A363378

Remove the 3 bolts and generator rear end cover.


Hide 3.REMOVE TERMINAL INSULATOR

a.
A363379

Remove the terminal insulator.


Hide 27370 4.REMOVE GENERATOR BRUSH HOLDER ASSEMBLY

a.
A363380

Remove the 2 screws and generator brush holder assembly.


Hide 27360 5.REMOVE GENERATOR COIL ASSEMBLY

a.
A363381

Remove the 4 bolts.


b.
A115868C02
0.771,0.26 1.344,0.594 false 2.635,0.458 3.125,0.896 0.49,0.438 10 *b 0.396,0.583 0.885,0.969 0.49,0.385 10 *a 0.448,0.156 0.958,0.573 0.51,0.417 10 SST
*a Hold
*b Turn


Using SST, remove the generator coil assembly.

SST
09950-40011  (09951-04020, 09952-04010, 09953-04020, 09954-04010, 09955-04071, 09957-04010, 09958-04011)


c.
A284548

Remove the bearing cover packing.

NOTICE:

If the bearing cover packing breaks, remove broken pieces completely.


HINT:

The bearing cover packing may be installed on the generator rotor assembly.



Hide 27330 6.REMOVE GENERATOR ROTOR ASSEMBLY

a.
A153384

Remove the generator rotor assembly.

NOTICE:

Do not drop the generator rotor assembly.



Hide 27310B 7.INSPECT GENERATOR DRIVE END FRAME BEARING

a.
A363383

Check that the generator drive end frame bearing is not rough or worn.

If necessary, replace the generator drive end frame bearing.


Hide 27310B 8.REMOVE GENERATOR DRIVE END FRAME BEARING

a.
A118441

Remove the 4 screws and retainer plate.


b.
A118442N02
1.24,0.938 0.479,0.813 0.479,0.813 1.208,1.313 true 0.146,0.729 0.833,1.208 0.688,0.479 10 SST

Using SST and a hammer, tap out the generator drive end frame bearing.

SST
09950-60010  (09951-00250)
09950-70010  (09951-07100)