Home › Power Source / Network › 2NR-VE BATTERY / CHARGING › GENERATOR › from 2015.08
RM19Y0E _57 Power Source / Network _041459 2NR-VE BATTERY / CHARGING _0192574 GENERATOR A

2NR-VE BATTERY / CHARGING  GENERATOR  REASSEMBLY  


PROCEDURE

Hide 27310B 1.INSTALL GENERATOR DRIVE END FRAME BEARING

a.
A237642N07
1.115,0.813 0.458,0.323 0.458,0.323 0.969,1.063 true 2.521,0.583 3.021,0.292 3.021,0.292 2.74,0.875 true 0.146,0.25 0.469,0.51 0.323,0.26 10 false SST 3.073,0.219 3.396,0.479 0.323,0.26 10 false SST

Using SST and a press, press in a new generator drive end frame bearing.

SST
09950-60010  (09951-00430)
09950-70010  (09951-07100)


b.
A153389C05
1.708,0.088 1.871,0.234 0.164,0.146 10 *a 2.185,1.708 2.349,1.867 0.164,0.159 10 *b 2.732,1.363 2.392,1.795 false 2.732,1.363 2.392,1.795 false 2.392,1.795 2.753,1.335 false 2.735,0.864 1.909,0.182 false
*a Tab
*b Cutout


Fit the tabs on the retainer plate into the cutouts on the generator drive end frame to install the retainer plate.


c.

Install the retainer plate to the generator drive end frame with the 4 screws.

Torque:
2.3 N*m (23 kgf*cm, 20 in.*lbf)


Hide 27330 2.INSTALL GENERATOR ROTOR ASSEMBLY

a.
A238333

Install the generator drive end frame on the generator pulley.


b.

Install the generator rotor assembly to the generator drive end frame.

NOTICE:

Do not drop the generator rotor assembly.



Hide 27360 3.INSTALL GENERATOR COIL ASSEMBLY

a.
A284548

Install a new bearing cover packing.

NOTICE:

Align the protrusion of the bearing cover packing with the groove of the generator coil assembly when installing.



b.
A285303C07
2.635,0.563 3.031,0.177 true 1.177,0.552 0.76,0.333 true 0.583,0.229 0.896,0.385 0.313,0.156 10 false *a 3.073,0.083 3.385,0.24 0.313,0.156 10 false *a
*a 21 mm Socket Wrench


Using a 21 mm socket wrench and press, slowly press the generator coil assembly to install it.


c.
A363381

Install the 4 bolts.

Torque:
5.9 N*m (60 kgf*cm, 52 in.*lbf)


Hide 27370 4.INSTALL GENERATOR BRUSH HOLDER ASSEMBLY

a.
A118452C11
1.354,0.552 0.99,0.813 true 1.406,0.448 1.844,0.844 0.438,0.396 10 false *a
*a Pin


While pushing the 2 brushes into the generator brush holder assembly, insert a 1.0 mm (0.0394 in.) pin into the generator brush holder assembly hole.


b.
A363384

Install the generator brush holder assembly to the generator coil assembly with the 2 screws.

Torque:
1.8 N*m (18 kgf*cm, 16 in.*lbf)


c.
A363385C01
1.854,0.781 2.74,0.229 true 2.802,0.156 3.115,0.354 0.313,0.198 10 false *a
*a Pin


Pull out the pin from the generator brush holder assembly hole.


Hide 5.INSTALL TERMINAL INSULATOR

a.
A363379

Install the generator terminal insulator to the generator coil assembly.


Hide 6.INSTALL GENERATOR REAR END COVER

a.
A363378

Install the generator rear end cover with the 3 bolts.

Torque:
4.6 N*m (47 kgf*cm, 41 in.*lbf)


Hide 7.INSTALL GENERATOR PULLEY

a.
A193553C05
2.844,0.708 2.531,1.198 true 3.083,0.583 3.083,1.531 true 1.229,1.458 1.542,1.823 0.313,0.365 10 *b 1.833,1.865 2.177,2.146 0.344,0.281 10 *a 2.198,1.229 2.875,1.729 0.677,0.5 10 SST1-B 2.781,1.573 3.354,2.052 0.573,0.479 10 SST1-A
*a Hold
*b Turn


Clamp the generator housing stay in a vise tightly.


b.

Install the generator pulley onto the generator rotor shaft by tightening the generator pulley nut by hand.


c.

Hold SST1-A with a torque wrench, and tighten SST1-B clockwise to the specified torque.

SST
09820-63011  (09820-06010, 09820-06021)

Item Part No.
SST 1-A and B 09820-06010
SST 2 09820-06021

Torque:
39 N*m (398 kgf*cm, 29 ft.*lbf)

NOTICE:

Check that SST is securely fitted onto the generator rotor shaft.



d.
A193554N08
2.531,0.49 2.667,0.906 false 2.125,0.365 2.76,0.844 0.635,0.479 10 SST2

Insert SST2, and engage SST2 to the pulley nut.


e.
A363386C01
1.323,0.219 2.656,0.458 true 1.333,0.656 3.031,0.875 true 1.323,2.688 1.635,2.885 0.313,0.198 10 false *a 2.135,2.823 2.448,3.021 0.313,0.198 10 false *b 0.938,0.135 1.802,0.375 0.865,0.24 10 false SST2 0.802,0.573 1.667,0.813 0.865,0.24 10 false SST1-A
*a Hold
*b Turn


Tighten the generator pulley nut by turning SST1-A in the direction shown in the illustration.

Torque:
133 N*m (1356 kgf*cm, 98 ft.*lbf)

HINT:

Hold the adjustable wrench against the vise and tighten the nut securely.



f.

Remove SST2 from the generator assembly.


g.
A363377C01
2.531,1.156 2.927,0.76 true 3.063,1.385 3.115,0.656 true 2.198,1.458 2.51,1.656 0.313,0.198 10 false *a 1.563,1.375 1.875,1.573 0.313,0.198 10 false *b 2.313,1.177 2.917,1.406 0.604,0.229 10 false SST1-B 2.802,1.406 3.406,1.635 0.604,0.229 10 false SST1-A
*a Hold
*b Turn


Hold SST1-A, Turn SST1-B, and remove SST1-A and SST1-B from the generator assembly.


h.

Turn the generator pulley, and check that the generator pulley moves smoothly.


i.

Remove the generator assembly from a vise.