Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2013.04–2015.08
RM19Y0E _58 Vehicle Interior _003010 SUPPLEMENTAL RESTRAINT SYSTEMS _0015213 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1662/45  Warning Lamp Drive Circuit Malfunctioning  


DESCRIPTION

The indicator light circuit consists of the center airbag sensor assembly and the combination meter assembly. DTC B1662/45 is set when a malfunction is detected in the indicator light circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1662/45 Warning Lamp Drive Circuit Malfunctioning
·

Center airbag sensor assembly detects line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in indicator light circuit for 2 seconds

·

Indicator light circuit malfunction

·

Center airbag sensor assembly malfunction


·

Instrument panel wire

·

Combination meter assembly

·

Center airbag sensor assembly


DTC is not output in check mode

WIRING DIAGRAM

C358421E02
0.302,0.979 1.875,1.333 1.573,0.354 10 false from ECU IG1 Fuse 0.292,2.156 1.865,2.51 1.573,0.354 10 false from ECU IG2 Fuse 2.406,2.052 2.729,2.333 0.323,0.281 10 false 39 2.396,3.042 2.719,3.323 0.323,0.281 10 false 16 2.688,3.76 3.125,3.979 0.438,0.219 10 false E34 2.677,3.927 4.667,4.292 1.99,0.365 10 false Combination Meter Assembly 3.552,3.052 3.99,3.271 0.438,0.219 10 false SRS 2.667,2.052 3.104,2.271 0.438,0.219 10 false IG 2.667,3.042 3.104,3.26 0.438,0.219 10 false E 4.375,2.063 4.813,2.281 0.438,0.219 10 false A/B 4.698,2.052 5.021,2.333 0.323,0.281 10 false 17 5.583,0.906 5.906,1.188 0.323,0.281 10 false 9 5.771,0.99 6.208,1.208 0.438,0.219 10 false IG1 5.531,2.052 5.854,2.333 0.323,0.281 10 false 21 5.781,2.156 6.219,2.375 0.438,0.219 10 false LA 5.521,4.344 5.844,4.625 0.323,0.281 10 false 19 5.792,4.438 6.229,4.656 0.438,0.219 10 false E1 5.573,5.875 6.01,6.094 0.438,0.219 10 false E60 5.573,6.031 6.906,6.5 1.333,0.469 10 false Center airbag sensor assembly

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK CONNECTOR (INSTRUMENT PANEL WIRE - CENTER AIRBAG SENSOR ASSEMBLY)
a.

Turn the ignition switch off.


b.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


c.

Disconnect the instrument panel wire connector from the center airbag sensor assembly.


d.

Check the instrument panel wire connector and terminals (on the center airbag sensor assembly side) and check that the connector is properly connected to the center airbag sensor assembly.


Result:
Result Proceed to
No problem. A
Connector and terminals incorrect. B
Connector connected improperly. C



A

2.CHECK CONNECTOR (INSTRUMENT PANEL WIRE - COMBINATION METER ASSEMBLY)

B

REPLACE INSTRUMENT PANEL WIRE

C

CONNECT CONNECTOR PROPERLY

2.CHECK CONNECTOR (INSTRUMENT PANEL WIRE - COMBINATION METER ASSEMBLY)
a.

Disconnect the instrument panel wire connector from the combination meter assembly.


b.

Check the instrument panel wire connector and terminals (on the combination meter assembly side) and check that the connector is properly connected to the combination meter assembly.

Result:
Result Proceed to
No problem. A
Connector and terminals incorrect. B
Connector connected improperly. C




A

3.CHECK INSTRUMENT PANEL WIRE

B

REPLACE INSTRUMENT PANEL WIRE

C

CONNECT CONNECTOR PROPERLY

3.CHECK INSTRUMENT PANEL WIRE
C275724C02
3.021,0.719 3.469,0.979 0.448,0.26 4.823,0.698 5.271,0.958 0.448,0.26 1.24,1.344 1.24,0.875 1.24,0.875 1.104,0.875 false 3.396,1.469 2.844,2.156 true 5.594,1.615 5.115,2.198 true 0.229,1.719 0.542,1.875 0.313,0.156 10 false *1 1.688,1.635 2,1.792 0.313,0.156 10 false *2 0.917,0.802 1.229,0.958 0.313,0.156 10 false *3 3.677,0.938 3.99,1.094 0.313,0.156 10 false *4 5.635,0.667 5.948,0.823 0.313,0.156 10 false *5 3.104,0.313 3.417,0.469 0.313,0.156 10 false *a 5.365,0.271 5.677,0.427 0.313,0.156 10 false *b 3.135,0.771 3.448,0.927 0.313,0.156 10 false E34 4.927,0.75 5.24,0.906 0.313,0.156 10 false E60 2.573,2.208 3.521,2.49 0.948,0.281 10 false 17 (A/B) 4.792,2.25 5.427,2.531 0.635,0.281 10 false 21 (LA) 1.802,1.313 2.021,1.521 0.219,0.208 10 false A 1.469,1.51 1.688,1.719 0.219,0.208 10 false B 0.917,1.51 1.135,1.719 0.219,0.208 10 false C 0.542,1.313 0.76,1.521 0.219,0.208 10 false D
*1 Combination Meter Assembly *2 Center airbag sensor assembly
*3 Instrument Panel Wire *4 Connector C
*5 Connector B - -
*a Rear view of wire harness connector
(to Combination Meter Assembly)
*b Rear view of wire harness connector
(to Center airbag sensor assembly)


a.

Disconnect the connectors from the center airbag sensor assembly and combination meter assembly.


b.

Check for short to B+ in the circuit.

i.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


ii.

Turn the ignition switch to ON.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E34-17 (A/B) - Body ground Ignition switch ON Below 1V




c.

Check for open in the circuit.

i.

Turn the ignition switch off.


ii.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E34-17 (A/B) - E60-21 (LA) Always Below 1Ω




d.

Check for short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E34-17 (A/B) - Body ground Always 1MΩ or higher




Result:
Proceed to
OK
NG



OK

4.CHECK SRS WARNING LIGHT CIRCUIT

NG

REPLACE INSTRUMENT PANEL WIRE

4.CHECK SRS WARNING LIGHT CIRCUIT
a.

Connect the instrument panel wire to the center airbag sensor assembly.

C275725C01
3.875,0.583 4.26,0.823 0.385,0.24 2.115,1.396 2.115,0.646 2.115,0.646 1.854,0.646 false 4.917,1.292 4.385,2.167 true 0.833,1.792 1.146,1.948 0.313,0.156 10 false *1 2.458,1.667 2.771,1.823 0.313,0.156 10 false *2 1.677,0.563 1.99,0.719 0.313,0.156 10 false *3 5.313,0.688 5.625,0.844 0.313,0.156 10 false *4 4.625,0.198 4.938,0.354 0.313,0.156 10 false *a 1.177,1.365 1.49,1.521 0.313,0.156 10 false D 1.75,1.615 2.063,1.771 0.313,0.156 10 false C 2.583,1.385 2.896,1.542 0.313,0.156 10 false A 3.948,0.625 4.26,0.781 0.313,0.156 10 false E34 4.063,2.219 4.75,2.458 0.688,0.24 10 false 17 (A/B)
*1 Combination Meter Assembly *2 Center airbag sensor assembly
*3 Instrument Panel Wire *4 Connector C
*a Rear view of wire harness connector
(to Combination Meter Assembly)
- -



b.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E34-17 (A/B) - Body ground For 6 seconds after ignition switch turned ON. Below 1V
After 6 seconds have passed since ignition switch turned ON. 11 to 14 V


Result:
Proceed to
OK
NG




OK

REPLACE COMBINATION METER ASSEMBLY

NG