TROUBLESHOOTING PRECAUTIONS
When there are malfunctions with terminal contact points or part installation problems, removal and installation of the suspected problem parts may return the system to the normal condition either completely or temporarily.
In order to determine the malfunctioning area, check the conditions at the time the malfunction occurred, such as DTC output and the Freeze Frame Data, and record them before disconnecting each connector or removing and installing parts.
Since the system may be influenced by malfunctions in systems other than the VSC system, be sure to check for DTCs in other systems.
The warning lights may come on depending on the vehicle operating condition or the type of work even when the system is operating properly.
| Warning Light | Possible Cause | Return Condition | Status of Controls |
|---|---|---|---|
·
ABS Warning Light ·
Brake Warning Light ·
TRC OFF Indicator Light ·
VSC OFF Indicator Light ·
Slip Indicator Light |
·
Only front wheels of a jacked-up vehicle are rotated at approx. 15 km/h (9 mph) or more. ·
Brake is dragging. ·
Sudden acceleration or deceleration |
Operation recovered to normal state after turning the ignition switch off and running at approx. 15 km/h (9 mph) or more. | ·
ABS control: non-functional. ·
EBD control: non-functional. ·
Brake assist control: non-functional. ·
TRC control: non-functional. ·
VSC control: non-functional. |
HANDLING PRECAUTIONS
Be sure to remove and install the skid control ECU (brake actuator assembly) and each sensor, etc. with the ignition switch off unless otherwise specified in the inspection procedure.
The skid control ECU (brake actuator assembly) and the sensors are precision components. Avoid strong shocks during removal or installation. Do not use them if subjected to strong shocks (such as dropping onto the floor).
When performing inspection on a rainy day, or during car wash, be careful not to splash water on the skid control ECU (brake actuator assembly) or the sensors to avoid water intrusion.
If replacing the skid control ECU (brake actuator assembly), always replace it with a new one (if the skid control ECU (brake actuator assembly) is not replaced with a new one, DTCs may be stored).
Do not use a skid control ECU (brake actuator assembly) from another vehicle (a vehicle display model, etc.).
If the ECU, brake actuator or a sensor has been removed and installed, it is necessary to check the system for problems after the parts have been reassembled. Check for DTCs using the GTS, and also check that system functions and signals received by the ECU are normal using Test Mode.
DTC PRECAUTION
Warnings for some DTCs cannot be cleared only by repairing the malfunctioning parts.
To clear the warning (turn off the warning light), delete DTC or perform the following operations.
| DTC No. | Operation Procedure |
|---|---|
| C1235/25
C1236/26 C1238/27 C1239/28 |
1.
Replace with a new one or repair. 2.
Turn the ignition switch to ON. 3.
Run at more than 15 km/h (9 mph). (Run at more than 55 km/h (34 mph) if the warning light does not turn off.) |
| C1251/51 | 1.
Replace with a new one or repair. 2.
Turn the ignition switch to ON. 3.
Run at more than 15 km/h (9 mph). (Run at more than 40 km/h (25 mph) if the warning light does not turn off.) |
| C1245/31 | 1.
Replace with a new one or repair. 2.
Turn the ignition switch to ON. 3.
Run at more than 5 km/h (3 mph). 4.
Apply brake normally to stop the vehicle. |
Be careful during driving and braking because when warnings are output (warning light is ON), the systems do not operate due to activation of the fail-safe mode.
If a DTC for a malfunctioning part reappears after it was cleared, then it has been stored again.
CHASSIS DYNAMOMETER PRECAUTION
Enter Inspection Mode to disable TRC and VSC operation when using a chassis dynamometer.
Refer to Inspection Mode Procedure: Click here
Do not use the drum tester with any of the lock chains disconnected.
Using the drum tester with a lock chain disconnected could cause the vehicle to begin moving unexpectedly.
Do not use the drum tester while the TRC or VSC is able to operate.
TRC or VSC operation could cause the vehicle to begin moving unexpectedly.
CAN COMMUNICATION SYSTEM PRECAUTIONS
The CAN communication system is used for data communication among the skid control ECU (brake actuator assembly), the steering sensor (switch base) and other ECUs. If there is trouble in the CAN communication line, corresponding communication line DTCs are output.
If any CAN communication line DTC is output, repair the malfunction in the communication line and troubleshoot the VSC system after data communication becomes normal.
In order to enable CAN communication, a specific type of wiring is used for the CAN communication lines. The wiring used for each communication line is a twisted pair of wires of equal length. A bypass wire should not be used because the data being transmitted will be corrupted.