FREEZE FRAME DATA
Whenever a DTC is stored, the skid control ECU (brake actuator assembly) stores the current vehicle (sensor) state as freeze frame data.
The skid control ECU (brake actuator assembly) stores the number of times (maximum: 31) the ignition switch has been turned from off to ON since the last time the ABS was activated.
If the vehicle is stopped or at a low speed (7 km/h (4 mph) or less), or if a DTC is stored, the skid control ECU (brake actuator assembly) stops counting the number of times the ignition switch has been turned from off to ON.
Freeze frame data at the time the ABS operates:
The skid control ECU (brake actuator assembly) stores and updates data whenever the ABS operates.
When the ECU stores data at the time a DTC is stored, the data stored during ABS operation is cleared.
Freeze frame data at the time a DTC is stored:
When the skid control ECU (brake actuator assembly) stores data at the time a DTC is stored, no updates are performed until the data is cleared.
CHECK FREEZE FRAME DATA
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.
According to the display on the GTS, select the trouble code data display with freeze frame data.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Vehicle speed | Maximum wheel speed sensor reading | Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202 mph) |
Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| Front/Rear G (Controlled) | Front/Rear G | Min.: -25.10 m/s2
Max.: 24.90 m/s2 |
- | During turning: Changes in proportion with acceleration |
| Master pressure sensor | Master cylinder pressure sensor reading | Min.: 0.00 V
Max.: 5.00 V |
Brake pedal released: 0.50 V | Reading increases when brake pedal is depressed |
| Vehicle acceleration | Vehicle acceleration | Min.: -25.10 m/s2
Max.: 24.90 m/s2 |
Vehicle stopped: 0 m/s2 | During deceleration/acceleration: Changes continuously |
| Master pressure sensor (change value) | Master cylinder pressure sensor change | Min.: -30.00 Mpa/s
Max.: 225.00 Mpa/s |
Brake pedal released or pedal held at constant position: 0.00 Mpa/s | When brake pedal is being operated: Changes in proportion with the pedal movement speed |
| Wheel speed sensor FR | Front speed sensor RH reading | Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202 mph) |
Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| Wheel speed sensor FL | Front speed sensor LH reading | Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202 mph) |
Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| Wheel speed sensor RR | Rear speed sensor RH reading | Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202 mph) |
Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| Wheel speed sensor RL | Rear speed sensor LH reading | Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202 mph) |
Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| Yaw rate sensor | Yaw rate sensor | Min.: -128 deg/s
Max.: 127 deg/s |
Vehicle stopped: 1 deg/s
Turning right: -128 to 3 deg/s Turning left: 2 to 127 deg/s |
- |
| Right/Left G (Controlled) | Right/Left G | Min.: -25.10 m/s2
Max.: 24.90 m/s2 |
- | During turning: Changes in proportion with acceleration |
| Accelerator angle ratio | Percentage of accelerator pedal opening angle | Min.: 0.0 %
Max.: 128.0 % |
Accelerator pedal released: 0.0% | During accelerator pedal operation: Changes in proportion with the pedal movement |
| Actual engine torque | Actual engine torque | Min.: -1024.0 Nm
Max.: 1024.0 Nm |
- | - |
| Steering angle sensor | Steering angle sensor | Min.: -3276.8 deg
Max.: 3276.8 deg |
Turning left: Positive value increases
Turning right: Negative value decreases |
- |
| +IG1voltage | +IG voltage value | Min.: 0.00 V
Max.: 20.00 V |
Ignition switch on: 11 to 14 V | Changes in proportion to battery voltage |
| Solenoid valve power voltage | +BS voltage Value | Min.: 0.00 V
Max.: 20.00 V |
Always: 11.00 to 14.00 V | Changes in proportion to battery voltage |
| VM1 | Motor voltage value | Min.: 0.00 V
Max.: 20.00 V |
Motor ON: 11.00 to 14.00 V
Motor OFF: 0.00 V |
Changes in proportion to battery voltage |
| +B1 | +BM voltage value | Min.: 0.00 V
Max.: 20.00 V |
Motor ON: 11.00 to 14.00 V
Motor OFF: 0.00 V |
Changes in proportion to battery voltage |
| IG-ON elapsed time | Time elapsed after ignition switch turned on | Min.: 0 sec
Max.: 65535 sec |
- | - |
| Gear position | Gear position information | Fail / 1st / 2nd / 3rd / 4th / 5th / 6th / 7th / P-N / R / Other than R | Actual gear position | - |
| TRC cut SW | VSC OFF switch(vehicle stability control switch) | ON or OFF | ON: Switch on
OFF: Switch off |
- |
| Buzzer | Meter buzzer | ON or OFF | - | - |
| Reserver level SW | Brake fluid level warning switch (Brake master cylinder reservoir assembly) | ON or OFF | ON: Switch on
OFF: Switch off |
- |
| TRC/VSC OFF mode | TRC/VSC OFF mode | TRC/VSC ON / TRC OFF/VSC ON / No data / TRC/VSC OFF | TRC/VSC ON: Normal mode
TRC OFF/VSC ON: TRC off mode TRC/VSC OFF: TRC, VSC off mode |
- |
| Operation system | Operated system status | No, ABS, VSC, TRC, BA, PBA, PB, HAC | - | ABS : ABS activated
VSC : VSC activated TRC: TRC activated BA: BA activated PBA: PBA activated* PB: PB activated* HAC: Hill-start assist control activated*
|
| Stop lamp SW | Stop light switch assembly | ON or OFF | ON: Brake pedal depressed
OFF: Brake pedal released |
- |
| PKB | Parking brake switch | ON or OFF | ON: Parking brake applied
OFF: Parking brake released |
- |
| IG ON frequency | Number of operations of ignition switch being turned to ON after storing Freeze Frame Data | 0 to 31 | - | - |
| Freeze elapsed Time | Elapsed time after storing freeze frame data | Min.: 0 ms
Max.: 500 ms |
- | - |
| Freeze frame No | Freeze frame No. | 0 to 255 | - | - |
| Elapse time (STP ON - control ON) | Elapsed time from braking to ABS or VSC control activation | Min.: 0 ms
Max.: 12750 ms |
- | - |
| Control continuous time | Control duration of ABS or VSC | Min.: 0 ms
Max.: 12750 ms |
- | - |
| Brake fluid level SW | Brake fluid level warning switch (Brake master cylinder reservoir assembly) | Normal or Low | Normal: Reservoir level normal
Low: Reservoir level low |
- |
| Torque reduction request | Torque reduction request | Not req or request | - | No change |
| Number of diagnosis codes | Number of DTCs stored | Min. : 0
Max. : 255 |
- | - |
CLEAR FREEZE FRAME DATA
Clearing the DTCs will also clear the freeze frame data.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS to ON.
Clear the DTCs and freeze frame data.
(See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR)