DATA LIST
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus:
for ABS/VSC/TRC: Chassis / ABS/VSC/TRC / Data List.
for Body: Body Electrical / Body / Data List.
According to the display on the GTS, read the Data List.
ABS/VSC/TRC
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Wheel speed FR | Front speed sensor RH reading | Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202 mph) |
Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| Wheel speed FL | Front speed sensor LH reading | Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202 mph) |
Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| Wheel speed RR | Rear speed sensor RH reading | Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202 mph) |
Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| Wheel speed RL | Rear speed sensor LH reading | Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202 mph) |
Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| Master pressure sensor 1 | Master cylinder pressure sensor 1 reading | Min.: 0.00 V
Max.: 5.00 V |
Brake pedal released: 0.50 V | Reading increases when brake pedal is depressed |
| Master pressure sensor 2 | Master cylinder pressure sensor 2 reading | Min.: 0.00 V
Max.: 5.00 V |
Brake pedal released: 0.50 V | Reading increases when brake pedal is depressed |
| Front/Rear G sensor | Front/Rear G sensor | Min.: -18.327 m/s2
Max.: 18.392 m/s2 |
- | During acceleration/deceleration: Changes in proportion with acceleration |
| Right/Left G sensor | Right/Left G sensor | Min.: -18.327 m/s2
Max.: 18.392 m/s2 |
- | During turning: Changes in proportion with acceleration |
| Engine RPM | Engine speed | Min.: 0 rpm
Max.: 65535 rpm |
Engine stopped: 0 rpm | When engine speed is constant: No large fluctuations |
| Accelerator angle ratio | Percentage of accelerator pedal opening angle | Min.: 0.0 %
Max.: 128.0 % |
Accelerator pedal released: 0.0% | During accelerator pedal operation: Changes in proportion with the pedal movement |
| Actual engine torque | Actual engine torque | Min.: -1024.0 Nm
Max.: 1024.0 Nm |
- | - |
| Yaw rate sensor 1 | Yaw rate sensor | Min.: -128 deg/s
Max.: 127 deg/s |
Vehicle stopped: 1 deg/s
Turning right: -128 to 3 deg/s Turning left: 2 to 127 deg/s |
- |
| Steering angle sensor | Steering angle sensor | Min.: -3276.8 deg
Max.: 3276.8 deg |
Turning left: Positive value increases
Turning right: Negative value decreases |
- |
| +IG 1 voltage | +IG voltage value | Min.: 0.00 V
Max.: 20.00 V |
Ignition switch on: 11 to 14 V | Changes in proportion to battery voltage |
| Solenoid valve power voltage | +BS voltage value | Min.: 0.00 V
Max.: 20.00 V |
Always: 11.00 to 14.00 V | Changes in proportion to battery voltage |
| VM1 | Motor voltage value | Min.: 0.00 V
Max.: 20.00 V |
Motor ON: 11.00 to 14.00 V
Motor OFF: 0.00 V |
Changes in proportion to battery voltage |
| +B1 | +BM voltage value | Min.: 0.00 V
Max.: 20.00 V |
Motor ON: 11.00 to 14.00 V
Motor OFF: 0.00 V |
Changes in proportion to battery voltage |
| Gear position | Gear position information | Fail / 1st / 2nd / 3rd / 4th / 5th / 6th / 7th / P-N / R / Other than R | Actual gear position | - |
| VSC OFF SW | VSC OFF switch(vehicle stability control switch) | ON or OFF | ON: Switch on
OFF: Switch off |
- |
| Brake fluid level SW | Brake fluid level warning switch (Brake master cylinder reservoir assembly) | ON or OFF | ON: Switch on
OFF: Switch off |
- |
| Stop lamp SW | Stop light switch assembly | ON or OFF | ON: Brake pedal depressed
OFF: Brake pedal released |
- |
| PKB SW | Parking brake switch | ON or OFF | OFF: Parking brake released
ON: Parking brake applied |
- |
| Meter vehicle speed Vout | Vehicle speed | Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202 mph) |
Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| Master cut solenoid 2 | Master cylinder cut solenoid status (FR RH and RR LH) | ON or OFF | ON: Solenoid on
OFF: Solenoid off |
- |
| Master cut solenoid 1 | Master cylinder cut solenoid status (FR LH and RR RH) | ON or OFF | ON: Solenoid on
OFF: Solenoid off |
- |
| Vehicle speed | Maximum wheel speed sensor reading | Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202 mph) |
Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| ABS warning lamp | ABS warning light | ON or OFF | ON: Warning light on
OFF: Warning light off |
- |
| Brake warning lamp | Brake warning light | ON or OFF | ON: Warning light on
OFF: Warning light off |
- |
| Buzzer | Meter buzzer | ON or OFF | - | - |
| VSC warning lamp | VSC OFF indicator light | ON or OFF | OFF: Indicator light off
ON: Indicator light on |
- |
| Slip indicator | Slip indicator light | ON or OFF | OFF: Indicator light off
ON: Indicator light on |
- |
| Solenoid relay | Solenoid relay | ON or OFF | ON: Solenoid relay on
OFF: Solenoid relay off |
- |
| Motor relay 1 | Motor relay | ON or OFF | ON: Motor relay on
OFF: Motor relay off |
- |
| Retention solenoid FR | Front wheel RH hold solenoid | ON or OFF | ON: Operates
OFF: Does not operate |
- |
| Press. reduction SOL FR | Front wheel RH release solenoid | ON or OFF | ON: Operates
OFF: Does not operate |
- |
| Retention solenoid FL | Front wheel LH hold solenoid | ON or OFF | ON: Operates
OFF: Does not operate |
- |
| Press. reduction SOL FL | Front wheel LH release solenoid | ON or OFF | ON: Operates
OFF: Does not operate |
- |
| Retention solenoid RR | Rear wheel RH hold solenoid | ON or OFF | ON: Operates
OFF: Does not operate |
- |
| Press. reduction SOL RR | Rear wheel RH release solenoid | ON or OFF | ON: Operates
OFF: Does not operate |
- |
| Retention solenoid RL | Rear wheel LH hold solenoid | ON or OFF | ON: Operates
OFF: Does not operate |
- |
| Press. reduction SOL RL | Rear wheel LH release solenoid | ON or OFF | ON: Operates
OFF: Does not operate |
- |
| Master pressure sensor (0 corrected value) | Master pressure sensor (0 corrected value) | Min.: -12.50 Mpa
Max.: 12.40 Mpa |
- | - |
| Master pressure sensor (corrected) | Master pressure sensor (corrected) | Min.: -1.00 Mpa
Max.: 23.99 Mpa |
- | - |
| Master pressure sensor (change value) | Master cylinder pressure sensor change | Min.: -30.00 Mpa/s
Max.: 25.00 Mpa/s |
Brake pedal released or pedal held at constant position: 0.00 Mpa/s | When brake pedal is being operated: Changes in proportion with pedal movement speed |
| Acceleration FR | Front wheel RH acceleration | Min.: -200.84 m/s2
Max.: 199.27 m/s2 |
- | During deceleration/acceleration: Changes continuously |
| Acceleration FL | Front wheel LH acceleration | Min.: -200.84 m/s2
Max.: 199.27 m/s2 |
- | During deceleration/acceleration: Changes continuously |
| Acceleration RR | Rear wheel RH acceleration | Min.: -200.84 m/s2
Max.: 199.27 m/s2 |
- | During deceleration/acceleration: Changes continuously |
| Acceleration RL | Rear wheel LH acceleration | Min.: -200.84 m/s2
Max.: 199.27 m/s2 |
- | During deceleration/acceleration: Changes continuously |
| Front/Rear G sensor correct value | Front/Rear G sensor correct value | Min.: -25.10 m/s2
Max.: 24.90 m/s2 |
- | - |
| Right/Left G sensor correct value | Right/Left G sensor correct value | Min.: -25.10 m/s2
Max.: 24.90 m/s2 |
- | - |
| Yaw rate sensor 0 correct value | Yaw rate sensor 0 correct value | Min.: -128.0 deg
Max.: 127.0 deg |
Zero point calibration of the yaw rate sensor is complete: 0deg | - |
| Steering angle sensor 0 correct value | Steering angle sensor 0 correct value | Min.: -3276.8 deg/s
Max.: 3276.7 deg/s |
Zero point calibration of the steering sensor (switch base) is complete: 0deg/s | - |
| Right/Left G (Controlled) | Right/Left G | Min.: -25.10 m/s2
Max.: 24.90 m/s2 |
- | During turning: Changes in proportion with acceleration |
| Front/Rear G (Controlled) | Front/Rear G | Min.: -25.10 m/s2
Max.: 24.90 m/s2 |
- | During acceleration/deceleration: Changes in proportion with acceleration |
| Yaw rate value | Yaw rate sensor value | Min.: -128.0 deg
Max.: 127.0 deg |
- | During turning: Changes in proportion with acceleration |
| Steering angle value | Steering angle sensor value | Min.: -3276.8 Deg
Max.: 3276.7 Deg |
- | During steering operation: Changes in proportion with steering wheel rotation |
| TRC control | TRC control | ON or OFF | ON: Operates
OFF: Does not operate |
- |
| Engine is being controlled (TRC) | TRC engine control status | ON or OFF | ON: During control
OFF: Not during control |
- |
| Brake is being controlled (TRC) | TRC brake control status | ON or OFF | ON: During control
OFF: Not during control |
- |
| TRC/VSC OFF mode | TRC/VSC OFF mode | TRC/VSC ON / TRC OFF/VSC ON / No data / TRC/VSC OFF | TRC/VSC ON: Normal mode
TRC OFF/VSC ON: TRC off mode No data: No data TRC/VSC OFF: TRC, VSC off mode |
- |
| FR VSC brake is being controlled | Front wheel RH VSC operation | ON or OFF | ON: During control
OFF: Not during control |
- |
| FL VSC brake is being controlled | Front wheel LH VSC operation | ON or OFF | ON: During control
OFF: Not during control |
- |
| RR VSC brake is being controlled | Rear wheel RH VSC operation | ON or OFF | ON: During control
OFF: Not during control |
- |
| RL VSC brake is being controlled | Rear wheel LH VSC operation | ON or OFF | ON: During control
OFF: Not during control |
- |
| VSC throttle close request | VSC throttle close request | ON or OFF | ON: During control
OFF: Not during control |
- |
| FR ABS is being controlled | Front wheel RH ABS operation | Not controlled or Controlled | Not controlled: During control
Controlled: Not during control |
- |
| FL ABS is being controlled | Front wheel LH ABS operation | Not controlled or Controlled | Not controlled: During control
Controlled: Not during control |
- |
| RR ABS is being controlled | Rear wheel RH ABS operation | Not controlled or Controlled | Not controlled: During control
Controlled: Not during control |
- |
| RL ABS is being controlled | Rear wheel LH ABS operation | Not controlled or Controlled | Not controlled: During control
Controlled: Not during control |
- |
| FR EBD is being controlled | Front wheel RH EBD operation | Not controlled or Controlled | Not controlled: During control
Controlled: Not during control |
- |
| FL EBD is being controlled | Front wheel LH EBD operation | Not controlled or Controlled | Not controlled: During control
Controlled: Not during control |
- |
| RR EBD is being controlled | Rear wheel RH EBD operation | Not controlled or Controlled | Not controlled: During control
Controlled: Not during control |
- |
| RL EBD is being controlled | Rear wheel LH EBD operation | Not controlled or Controlled | Not controlled: During control
Controlled: Not during control |
- |
| Brake assist is being controlled | Brake assist is being controlled | Not controlled or Controlled | Not controlled: During control
Controlled: Not during control |
- |
| FR wheel speed sensor temp cutout | Front speed sensor RH open detection | Normal or Cutout | Normal: Normal
Cutout: Momentary interruption |
Refer to DTC C0200/21. |
| FL wheel speed sensor temp cutout | Front speed sensor LH open detection | Normal or Cutout | Normal: Normal
Cutout: Momentary interruption |
Refer to DTC C0205/22. |
| RR wheel speed sensor temp cutout | Rear speed sensor RH open detection | Normal or Cutout | Normal: Normal
Cutout: Momentary interruption |
Refer to DTC C0210/23. |
| RL wheel speed sensor temp cutout | Rear speed sensor LH open detection | Normal or Cutout | Normal: Normal
Cutout: Momentary interruption |
Refer to DTC C0215/24. |
| EFI communication temp cutout | EFI communication open detection | Normal or Cutout | Normal: Normal
Cutout: Momentary interruption |
Refer to DTC U0100/49. |
| Yaw rate sensor temp cutout | Yaw rate sensor open detection | Normal or Cutout | Normal: Normal
Cutout: Momentary interruption |
Refer to DTC U0126/19. |
| M/C pressure sensor cutout | M/C pressure sensor open detection | Normal or Cutout | Normal: Normal
Cutout: Momentary interruption |
Refer to DTC C1246/43. |
| IG voltage low | IG voltage value decreased | Normal or Abnormal | Normal: Normal
Abnormal: Momentary interruption |
Refer to DTC C1241/15. |
| IG voltage high | IG voltage value increased | Normal or Abnormal | Normal: Normal
Abnormal: Momentary interruption |
Refer to DTC C1241/16. |
| FR wheel speed sensor power temp cutout | Front speed sensor RH voltage open detection | Normal or Cutout | Normal: Normal
Cutout: Momentary interruption |
Refer to DTC C0200/21. |
| FL wheel speed sensor power temp cutout | Front speed sensor LH voltage open detection | Normal or Cutout | Normal: Normal
Cutout: Momentary interruption |
Refer to DTC C0205/22. |
| RR wheel speed sensor power temp cutout | Rear speed sensor RH voltage open detection | Normal or Cutout | Normal: Normal
Cutout: Momentary interruption |
Refer to DTC C0210/23. |
| RL wheel speed sensor power temp cutout | Rear speed sensor LH voltage open detection | Normal or Cutout | Normal: Normal
Cutout: Momentary interruption |
Refer to DTC C0215/24. |
| M/C pressure sensor noise | Master cylinde rpressure sensor noise detection | Normal or Noise | Normal: Normal
Noise: Momentary interruption |
Refer to DTC C1246/43. |
| Number of diagnosis codes | Number of DTCs stored | Min. : 0
Max. : 255 |
- | - |
Body
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Stop SW | Stop light switch signal | ON or OFF | ON: Stop light switch on
OFF: Stop light switch off |
- |
| Brake Fluid SW | Brake level warning switch | ON or OFF | ON: Brake fluid switch on
OFF: Brake fluid switch off |
- |
ACTIVE TEST
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.
According to the display on the GTS, perform the Active Test.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Stop lamp relay | - | - | This item is displayed on the GTS but is not used |
| ABS motor relay | ABS motor relay | Relay ON / OFF | Operating sound of motor can be heard.
Vehicle condition: Vehicle stopped |
| Solenoid relay | - | - | This item is displayed on the GTS but is not used |
| Brake warning lamp | Brake warning light | Warning light ON / OFF | Observe the combination meter assembly.
Vehicle condition: Vehicle stopped |
| ABS warning lamp | ABS warning light | Warning light ON / OFF | Observe the combination meter assembly.
Vehicle condition: Vehicle stopped |
| Buzzer | Meter buzzer | Buzzer ON / OFF | Observe the combination meter assembly.
Vehicle condition: Vehicle stopped |
| TRC OFF lamp | TRC OFF indicator light | Indicator light ON / OFF | Observe the combination meter assembly.
Vehicle condition: Vehicle stopped |
| VSC OFF lamp | VSC OFF indicator light | Indicator light ON / OFF | Observe the combination meter assembly.
Vehicle condition: Vehicle stopped |
| Slip indicator | Slip indicator light | Indicator light ON / OFF | Observe the combination meter assembly.
Vehicle condition: Vehicle stopped |
| SRLR | Solenoid (SRLR) | Solenoid ON / OFF | Operating sound of solenoid (clicking sound) can be heard.
Vehicle condition: Vehicle stopped |
| SRLH | Solenoid (SRLH) | Solenoid ON / OFF | Operating sound of solenoid (clicking sound) can be heard.
Vehicle condition: Vehicle stopped |
| SRRR | Solenoid (SRRR) | Solenoid ON / OFF | Operating sound of solenoid (clicking sound) can be heard.
Vehicle condition: Vehicle stopped |
| SRRH | Solenoid (SRRH) | Solenoid ON / OFF | Operating sound of solenoid (clicking sound) can be heard.
Vehicle condition: Vehicle stopped |
| SFLR | Solenoid (SFLR) | Solenoid ON / OFF | Operating sound of solenoid (clicking sound) can be heard.
Vehicle condition: Vehicle stopped |
| SFLH | Solenoid (SFLH) | Solenoid ON / OFF | Operating sound of solenoid (clicking sound) can be heard.
Vehicle condition: Vehicle stopped |
| SFRR | Solenoid (SFRR) | Solenoid ON / OFF | Operating sound of solenoid (clicking sound) can be heard.
Vehicle condition: Vehicle stopped |
| SFRH | Solenoid (SFRH) | Solenoid ON / OFF | Operating sound of solenoid (clicking sound) can be heard.
Vehicle condition: Vehicle stopped |
| Master cut solenoid 2 | Master cut solenoid 2 | Solenoid ON / OFF | Operating sound of solenoid (clicking sound) can be heard.
Vehicle condition: Vehicle stopped |
| Master cut solenoid 1 | Master cut solenoid 1 | Solenoid ON / OFF | Operating sound of solenoid (clicking sound) can be heard.
Vehicle condition: Vehicle stopped |
| 2nd system air bleed | 2nd sys. Air bleeding | Secondary solenoid ON / OFF | Pump motor drive (used when removing air inside ABS actuator) |
| ACT RL | Actuator drive(RL) | Solenoid ON / OFF | Operating sound of solenoid (clicking sound) can be heard.
Vehicle condition: Vehicle stopped |
| ACT RR | Actuator drive(RR) | Solenoid ON / OFF | Operating sound of solenoid (clicking sound) can be heard.
Vehicle condition: Vehicle stopped |
| ACT FL | Actuator drive(FL) | Solenoid ON / OFF | Operating sound of solenoid (clicking sound) can be heard.
Vehicle condition: Vehicle stopped |
| ACT FR | Actuator drive(FR) | Solenoid ON / OFF | Operating sound of solenoid (clicking sound) can be heard.
Vehicle condition: Vehicle stopped |