Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE FLUID › from 2016.09
RM19Y0E _54 Brake _002993 BRAKE SYSTEM (OTHER) _0015143 BRAKE FLUID N

BRAKE SYSTEM (OTHER)  BRAKE FLUID  BLEEDING  


CAUTION / NOTICE / HINT

NOTICE:

Immediately wash off any brake fluid that comes into contact with any painted surfaces.


HINT:

If any work is done on the brake system or if air in the brake lines is suspected, bleed the air from the system.


PROCEDURE

Hide 1. FILL RESERVOIR WITH BRAKE FLUID

a.
C152660C01
2,0.677 2.625,0.156 true 2.719,0.833 2.177,0.833 true 2.656,0.031 3.031,0.396 0.375,0.365 10 *a 2.792,0.75 3.292,1.229 0.5,0.479 10 *b
*a MAX Line
*b MIN Line


Fill the reservoir with brake fluid.

Fluid:

SAE J1703 or FMVSS No. 116 DOT3


NOTICE:

Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while bleeding the brakes.



Hide 47201 2.BLEED BRAKE MASTER CYLINDER SUB-ASSEMBLY

HINT:

If the master cylinder has been disassembled or if the reservoir becomes empty, bleed the air from the master cylinder.


a.
C332255

Using a union nut wrench, disconnect the 2 brake tubes from the master cylinder.


b.
C363894

Slowly depress the brake pedal and hold it there (Step A).


c.
C363895

Block the outer holes with your fingers, and release the brake pedal (Step B).


d.

Repeat steps A and B 3 or 4 times.


e.
C333859C01
1.448,2.385 1.667,2.604 0.219,0.219 10 false *a
*a Torque Wrench Fulcrum Length


Using union nut wrench, connect the 2 brake tubes to the master cylinder.

Torque:
Specified tightening torque (w/o VSC) : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)
Specified tightening torque (w/VSC) : 19.6 N*m (200 kgf*cm, 14 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

w/o VSC (10 mm Flare Nut): When using a union nut wrench (fulcrum length of 22 mm (0.8661 in.)) + torque wrench (fulcrum length of 162 mm (6.3779 in.)):

13.4 N*m (137 kgf*cm, 10 ft.*lbf)

·

w/ VSC (12 mm Flare Nut): When using a union nut wrench (fulcrum length of 20 mm (0.7874 in.)) + torque wrench (fulcrum length of 162 mm (6.3779 in.)):

17.4 N*m (177 kgf*cm, 13 ft.*lbf)




Hide 3.BLEED BRAKE LINE

NOTICE:
·

Bleed the brake line of the wheel farthest from the master cylinder first.

·

Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while bleeding the brakes.



a.
C152601

Connect the vinyl tube to the bleeder plug.


b.

Depress the brake pedal several times, then loosen the bleeder plug with the pedal depressed (Step C).


c.

At the point where the fluid stops coming out, tighten the bleeder plug, then release the brake pedal (Step D).


d.

Repeat steps C and D until all air in the fluid is completely bled out.


e.

Tighten the bleeder plug.

Torque:
Front Brake : 8.3 N*m (85 kgf*cm, 74 in.*lbf)
Rear Brake : 11 N*m (110 kgf*cm, 8 ft.*lbf)


f.

Repeat the above procedure to bleed the air out of the brake line for each wheel.


Hide 4.INSPECT FOR BRAKE FLUID LEAK