Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2016.09
RM19Y0E _58 Vehicle Interior _003008 METER / GAUGE / DISPLAY _0015206 METER / GAUGE SYSTEM U

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  TERMINALS OF ECU  


CHECK COMBINATION METER ASSEMBLY


E177004N08
3.458,0.188 3.875,0.427 0.417,0.24 3.531,0.229 4.115,0.594 0.583,0.365 10 E34

a.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
E34-3 (+B) - Body ground P - Body ground Battery power supply Always 11 to 14 V
E34-5 (IG) - Body ground R - Body ground Ignition switch power supply Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
E34-7 (E) - Body ground BR - Body ground Ground Always below 1 Ω
E34-8 (CANL) - Body ground P - Body ground CAN communication signal Ignition switch ON Pulse generation
E34-9 (CANH) - Body ground W - Body ground CAN communication signal Ignition switch ON Pulse generation
E34-10 (SPDO) - Body ground G - Body ground Speed signal for other system (Output) Ignition switch ON, wheel being rotated Pulse generation
(See waveform 1)
E34-12 (T) - Body ground SB - Body ground DLC3 Communication Always 11 to 14 V
E34-14 (+) - Body ground V - Body ground Fuel sender gauge signal input Fuel F (full tank) Below 1 V
Fuel E (empty) 4.5 to 9 V
E34-15 (PKB) - Body ground GR - Body ground Parking brake switch signal input Ignition switch ON, parking brake switch off 11 to 14 V
Ignition switch ON, parking brake switch on Below 1 V
E34-17 (TCS) - Body ground R - Body ground Vehicle stability control switch signal input Ignition switch ON, VSC OFF switch held on → off (Released) 11 to 14 V → Below 1 V
E34-19 (BTWG) - Body ground R - Body ground Front passenger side seat belt warning light signal output Ignition switch ON, front passenger seat not occupied, or front passenger seat belt fastened 11 to 14 V
Ignition switch ON, front passenger seat occupied, and front passenger seat belt unfastened Pulse generation
E34-20 (LD+) - Body ground G - Body ground Clearance sonar indicator light signal input Ignition switch ON, Clearance sonar indicator light on Below 1 V
Ignition switch ON, Clearance sonar indicator light off 11 to 14 V
E34-24 (+) - Body ground LG - Body ground LH side turn signal light signal input Ignition switch ON, turn signal switch neutral position Below 1 V
Ignition switch ON, turn signal switch turned to left Alternating between below 1 and 11 to 14 V
E34-25 (+) - Body ground BE - Body ground RH side turn signal light signal input Ignition switch ON, turn signal switch neutral position Below 1 V
Ignition switch ON, turn signal switch turned to right Alternating between below 1 and 11 to 14 V
E34-26 (SECR) - Body ground Y - Body ground Security indicator light signal input Immobiliser system is unset Below 1 V
Immobiliser system is set Pulse generation
(See waveform 2)
E34-34 (IND) - Body ground L - Body ground Tire pressure warning reset switch signal Ignition switch ON, tire pressure warning reset switch off 8 to 15 V
Ignition switch ON, tire pressure warning reset switch pressed and held Below 1.5 V

If the result is not as specified, the meter may have a malfunction.



b.
E267248E11
2.969,1.198 3.323,1.396 0.354,0.198 10 false GND 1.156,1.625 1.365,1.833 0.208,0.208 10 false A

Using an oscilloscope, check waveform 1.

Measurement Condition
Item Condition
Terminal No. (Symbol) E34-10 (SPDO) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Condition Ignition switch ON, wheel being rotated

HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.



c.
B366397E03
2.969,0.979 3.406,1.396 0.438,0.417 10 false GND

Using an oscilloscope, check waveform 2.

Measurement Condition
Item Condition
Terminal No. (Symbol) E34-26 (SECR) - Body ground
Tool setting 5 V/DIV., 500 ms./DIV.
Condition Immobiliser system is set