DATA LIST
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Using the GTS or Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS or Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the GTS or Techstream on.
Enter the following menus: Body Electrical / Meter / Data List.
Check the values by referring to the table below.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| ODO/TRIP Changing SW | ODO/TRIP switch | OFF or ON | OFF: Switch released
ON: Switch pushed |
- |
| P Seatbelt Buckle Switch | Front passenger seat belt buckle switch | OFF or ON | OFF: Front passenger seat belt fastened (warning light off)
ON: Front passenger seat belt unfastened (warning light on) |
- |
| Clock SW | Clock Switch | OFF or ON | OFF: Clock switch released
ON: Clock switch pushed |
- |
| TRC OFF SW | TRC OFF Switch | OFF or ON | OFF: TRC OFF switch released
ON: TRC OFF Switch pushed |
- |
| +B Voltage Value | Battery voltage | Min.: 0 V
Max.: 25.5 V |
11 to 14 V | - |
| Tire pressure | Tire pressure status | OFF / ON / Open/Short | OFF: TPMS ON
ON: TPMS Off |
- |
| Vehicle Speed | Vehicle speed | Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph) |
Almost the same as actual vehicle speed | - |
| Engine RPM | Engine speed | Min.: 0 rpm
Max.: 12750 rpm |
550 to 650 rpm: Idling (for Manual Transmission)
600 to 750 rpm: Idling (for Automatic Transmission) |
- |
| Coolant temperature | Engine coolant temperature | Min.: 0°C (0°F)
Max.: 127.5°C (261.5°F) |
75 to 100°C (167 to 212°F): After warming up engine | - |
| Remaining fuel amount | Fuel level | Min.: 0 L
Max.: 127.5 L |
Fuel level input value | Unit: Liter |
| Eco lamp | The condition of the ECO driving indicator light in the combination meter assembly | OFF or ON | OFF: ECO driving indicator in the combination meter assembly is OFF
ON: ECO driving indicator in the combination meter assembly comes on according to the drive condition |
The customized setting of the ECO driving indicator displayed |
| Flasher Buzzer | Condition of flasher buzzer sound setting | OFF or ON | OFF: Flasher buzzer sound setting is OFF
ON: Flasher buzzer sound setting is ON |
Displays customize setting of flasher buzzer sound setting |
| Number of Trouble Codes | The number of the DTC currently stored | Min.: 0
Max.: 255 |
0 | - |
ACTIVE TEST
Using the GTS or Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the GTS or Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the GTS or Techstream on.
Enter the following menus: Body Electrical / Meter / Active Test.
Check the operation by referring to the table below.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Speed meter | Speedometer | 0, 40, 80, 120, 160, 200 km/h | The meter needle goes off the scale when 200 km/h is selected. |
| Tachometer | Tachometer | 0, 1000, 2000, 3000, 4000, 5000, 6000, 7000 | - |
| Indicator 1 | Shift indicator | L, 2, 3, D, N, R, P | - |
| Display 1 | Multi-information display | Full ON | - |
| Indicator 1 | Corresponding indicator light in combination meter assembly | AIR BAG, Rr.FOG, Fr.FOG, BEAM | - |
| Indicator 2 | Corresponding indicator light in combination meter assembly | DOOR Ind, P Seat Belt, D Seat Belt | - |
| Indicator 3 | Corresponding indicator light in combination meter assembly | ABS Warning, Charge Warning, Fuel Warning | - |
| Indicator 4 | Corresponding indicator light in combination meter assembly | TIRE PRESSURE, TRC OFF, SLIP | - |
| Indicator 5 | Corresponding indicator light in combination meter assembly | Eco Ind, High temp, Oil Warning, Brake warning | - |
| Indicator 6 | Corresponding indicator light in combination meter assembly | EPS | The EPS warning light lights up in red. |
| Indicator 8 | Corresponding indicator light in combination meter assembly | Middle East120km/h | - |
| Indicator 10 | Corresponding indicator light in combination meter assembly | PARK | - |
| Indicator 13 | Corresponding indicator light in combination meter assembly | SLIP OFF (VSC OFF) | - |
| Indicator 14 | Corresponding indicator light in combination meter assembly | EPS | The EPS warning light lights up in yellow. |
| Indicator 18 | Corresponding indicator light in combination meter assembly | CVT warning, Engine warning | The AT warning light lights up when CVT warning is selected. |