Home › General › INTRODUCTION › WHEN REMOVING,INSTALLING,REPAIRING OR REPLACING PARTS › 2019.09–2020.08
BM32K0E _V1 General _060876 INTRODUCTION _0298447 WHEN REMOVING,INSTALLING,REPAIRING OR REPLACING PARTS F

INTRODUCTION  WHEN REMOVING,INSTALLING,REPAIRING OR REPLACING PARTS  WHEEL ALIGNMENT STANDARD  


The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after completing the front wheel alignment procedure are shown below.

Necessary Procedures After Procedure Performed
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Note
Front wheel alignment adjustment
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


for Initialization
for Calibration

MEASURE VEHICLE HEIGHT


NOTICE:
·

Before inspecting the wheel alignment, adjust the vehicle height to the specified value.

·

Be sure to perform measurement on a level surface.

·

If it is necessary to go under the vehicle for measurement, confirm that the parking brake is applied and the vehicle is secured with chocks.

·

Inspect while the vehicle is unloaded.

·

The standard value shown here is a value that is used for performing a wheel alignment and does not indicate the height of an actual vehicle.



a.

Bounce the vehicle up and down at the corners to stabilize the suspension.


b.
C362078N01
0.865,1.135 1.021,1.333 0.156,0.198 10 false A 2.323,1.219 2.479,1.417 0.156,0.198 10 false B 0.865,3.99 1.021,4.188 0.156,0.198 10 false C 2.354,4.021 2.51,4.219 0.156,0.198 10 false D

Measure the vehicle height.

Measurement Points:

A: Ground clearance of front wheel center


B: Ground clearance of front lower No. 1 suspension arm sub-assembly x front suspension crossmember sub-assembly set bolt center


C: Ground clearance of rear wheel center


D: Ground clearance of rear No. 2 suspension arm assembly x rear suspension member sub-assembly set bolt center


Vehicle Height (Unloaded Vehicle) (for TMC Made):
Engine Tire Size Front A - B Rear C - D
2ZR-FXE 215/60R17 115 mm (4.53 in.) 35 mm (1.38 in.)
225/50R18 115 mm (4.53 in.) 35 mm (1.38 in.)


Vehicle Height (Unloaded Vehicle) (for TMMT Made):
Engine Tire Size Front A - B Rear C - D

*1: except Rough Road Area Specification Vehicles

*2: for Rough Road Area Specification Vehicles

2ZR-FXE 215/60R17 121 mm (4.76 in.)*1
111 mm (4.37 in.)*2
43 mm (1.69 in.)*1
33 mm (1.30 in.)*2
225/50R18 121 mm (4.76 in.) 43 mm (1.69 in.)
M20A-FXS 215/60R17 122 mm (4.80 in.) 43 mm (1.69 in.)
225/50R18 123 mm (4.84 in.) 44 mm (1.73 in.)




INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION (FRONT WHEEL ALIGNMENT)


NOTICE:

Inspect while the vehicle is unloaded.


a.
C132440C16
2.396,1.104 2.51,0.823 2.51,0.823 2.74,0.823 false 0.604,0.708 1.031,0.708 1.031,0.708 1.031,1.458 false 2.76,0.729 2.99,0.906 0.229,0.177 10 false *b 0.448,0.604 0.688,0.781 0.24,0.177 10 false *a
*a Turning Radius Gauge
*b Camber-caster-kingpin Gauge


Install a camber-caster-kingpin gauge and place the front wheels on the center of a turning radius gauge.


b.

Inspect the camber, caster and steering axis inclination.

Camber (Unloaded Vehicle) (for TMC Made):
Engine Tire Size Camber Inclination Right-left Difference
2ZR-FXE 215/60R17 0°04' +/- 0°45' (0.07° +/- 0.75°) 0°45' (0.75°) or less
225/50R18 0°04' +/- 0°45' (0.07° +/- 0.75°)


Camber (Unloaded Vehicle) (for TMMT Made):
Engine Tire Size Camber Inclination Right-left Difference

*1: except Rough Road Area Specification Vehicles

*2: for Rough Road Area Specification Vehicles

2ZR-FXE 215/60R17 0°02' +/- 0°45' (0.03° +/- 0.75°)*1
0°06' +/- 0°45' (0.10° +/- 0.75°)*2
0°45' (0.75°) or less
225/50R18 0°02' +/- 0°45' (0.03° +/- 0.75°)
M20A-FXS 215/60R17 0°02' +/- 0°45' (0.03° +/- 0.75°)
225/50R18 0°02' +/- 0°45' (0.03° +/- 0.75°)


Caster (Unloaded Vehicle) (for TMC Made):
Engine Tire Size Caster Inclination Right-left Difference
2ZR-FXE 215/60R17 6°39' +/- 0°45' (6.65° +/- 0.75°) 0°45' (0.75°) or less
225/50R18 6°40' +/- 0°45' (6.67° +/- 0.75°)


Caster (Unloaded Vehicle) (for TMMT Made):
Engine Tire Size Caster Inclination Right-left Difference

*1: except Rough Road Area Specification Vehicles

*2: for Rough Road Area Specification Vehicles

2ZR-FXE 215/60R17 6°46' +/- 0°45' (6.77° +/- 0.75°)*1
6°36' +/- 0°45' (6.60° +/- 0.75°)*2
0°45' (0.75°) or less
225/50R18 6°48' +/- 0°45' (6.80° +/- 0.75°)
M20A-FXS 215/60R17 6°47' +/- 0°45' (6.78° +/- 0.75°)
225/50R18 6°49' +/- 0°45' (6.82° +/- 0.75°)


Steering Axis Inclination (Unloaded Vehicle) (for TMC Made):
Engine Tire Size Steering Axis Inclination Reference
2ZR-FXE 215/60R17 13°53' (13.88°)
225/50R18 13°53' (13.88°)


Steering Axis Inclination (Unloaded Vehicle) (for TMMT Made):
Engine Tire Size Steering Axis Inclination Reference

*1: except Rough Road Area Specification Vehicles

*2: for Rough Road Area Specification Vehicles

2ZR-FXE 215/60R17 13°55' (13.92°)*1
13°43' (13.72°)*2
225/50R18 13°56' (13.93°)
M20A-FXS 215/60R17 13°56' (13.93°)
225/50R18 13°56' (13.93°)




INSPECT TOE-IN (FRONT WHEEL ALIGNMENT)


NOTICE:

Inspect while the vehicle is unloaded.


a.

Bounce the vehicle up and down at the corners to stabilize the suspension.


b.

Release the parking brake and move the shift lever to N.


c.

Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step C)


d.
C188968C01
0.833,0.583 0.833,1.115 false 1.365,0.583 1.365,0.99 1.365,0.99 0.833,0.99 false 2.521,1.333 2.521,1.667 false 0.74,1.135 0.917,1.302 0.177,0.167 10 *a 2.427,1.698 2.604,1.854 0.177,0.156 10 *b
*a Tread Center Mark
*b Dimension B
V100135

Front of the Vehicle


Put tread center marks on the rearmost points of the front wheels and measure the distance between the marks (dimension B).


e.

Slowly push the vehicle straight ahead to cause the front wheels to rotate 180°. Use the front tire valve as a reference point.

HINT:

Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from step C again.



f.
C188969C01
0.646,1.271 0.646,1.635 false 1.917,0.542 2.052,0.698 0.135,0.156 10 C 3.073,0.552 3.208,0.708 0.135,0.156 10 D 2.5,0.719 2.635,0.875 0.135,0.156 10 A 2.51,1.542 2.646,1.698 0.135,0.156 10 B 0.563,1.656 0.74,1.813 0.177,0.156 10 *a
*a Dimension A
V100135

Front of the Vehicle


Measure the distance between the tread center marks on the front of the wheels (dimension A).

Toe-in (Unloaded Vehicle) (for TMC Made):
Engine Tire Size Specified Condition
2ZR-FXE 215/60R17 C + D: 0°05' +/- 0°10' (0.08° +/- 0.17°)
B - A: 1.0 +/- 2.0 mm (0.0394 +/- 0.0787 in.)
225/50R18 C + D: 0°05' +/- 0°10' (0.08° +/- 0.17°)
B - A: 1.0 +/- 2.0 mm (0.0394 +/- 0.0787 in.)


Toe-in (Unloaded Vehicle) (for TMMT Made):
Engine Tire Size Specified Condition

*1: except Rough Road Area Specification Vehicles

*2: for Rough Road Area Specification Vehicles

2ZR-FXE 215/60R17 C + D: 0°07' +/- 0°10' (0.12° +/- 0.17°)*1
C + D: 0°06' +/- 0°10' (0.10° +/- 0.17°)*2
B - A: 1.4 +/- 2.0 mm (0.0551 +/- 0.0787 in.)*1
B - A: 1.2 +/- 2.0 mm (0.0472 +/- 0.0787 in.)*2
225/50R18 C + D: 0°07' +/- 0°10' (0.12° +/- 0.17°)
B - A: 1.3 +/- 2.0 mm (0.0512 +/- 0.0787 in.)
M20A-FXS 215/60R17 C + D: 0°07' +/- 0°10' (0.12° +/- 0.17°)
B - A: 1.3 +/- 2.0 mm (0.0512 +/- 0.0787 in.)
225/50R18 C + D: 0°07' +/- 0°10' (0.12° +/- 0.17°)
B - A: 1.3 +/- 2.0 mm (0.0512 +/- 0.0787 in.)


HINT:

Measure "B - A" only when "C + D" cannot be measured.


If the toe-in is not within the specified range, adjust it at the steering rack ends.



INSPECT WHEEL ANGLE (FRONT WHEEL ALIGNMENT)


a.
C132439C03
0.863,0.204 1.036,0.381 0.173,0.177 10 *b 0.538,0.204 0.713,0.381 0.176,0.177 10 *a 2.397,0.204 2.57,0.381 0.173,0.177 10 *b 2.725,0.204 2.901,0.381 0.176,0.177 10 *a
*a Inside
*b Outside
V100135

Front of the Vehicle


Put tread center marks on the rearmost points of a turning radius gauge.


b.

Turn the steering wheel fully to the left and right and measure the turning angle.

NOTICE:

Inspect while the vehicle is unloaded.


Wheel Turning Angle (Unloaded Vehicle) (for TMC Made):
Engine Tire Size Inside Wheel Outside Wheel
2ZR-FXE 215/60R17 39°26' +/- 2°00' (39.43° +/- 2.00°) 33°46' (33.77°)
225/50R18 39°26' +/- 2°00' (39.43° +/- 2.00°) 33°46' (33.77°)


Wheel Turning Angle (Unloaded Vehicle) (for TMMT Made):
Engine Tire Size Inside Wheel Outside Wheel

*1: except Rough Road Area Specification Vehicles

*2: for Rough Road Area Specification Vehicles

2ZR-FXE 215/60R17 39°16' +/- 2°00' (39.27° +/- 2.00°)*1
39°30' +/- 2°00' (39.50° +/- 2.00°)*2
33°35' (33.58°)*1
33°50' (33.83°)*2
225/50R18 39°16' +/- 2°00' (39.27° +/- 2.00°) 33°35' (33.58°)
M20A-FXS 215/60R17 39°15' +/- 2°00' (39.25° +/- 2.00°) 33°34' (33.57°)
225/50R18 39°15' +/- 2°00' (39.25° +/- 2.00°) 33°34' (33.57°)


If the right and left inside wheel angles differ from the specified value, check and adjust the right and left steering rack end lengths.




Necessary Procedures After Procedure Performed
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Note
Rear wheel alignment adjustment
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


for Initialization
for Calibration

INSPECT CAMBER (REAR WHEEL ALIGNMENT)


NOTICE:

Inspect while the vehicle is unloaded.


a.
C107736C10
2.052,1.26 2.375,1.26 false 2.406,1.167 2.656,1.385 0.25,0.219 10 *a
*a Camber-caster-kingpin Gauge


Install a camber-caster-kingpin gauge.


b.

Inspect the camber.

Camber (Unloaded Vehicle) (for TMC Made):
Engine Tire Size Camber Inclination Right-left Difference
2ZR-FXE 215/60R17 -0°45' +/- 0°45' (-0.75° +/- 0.75°) 0°45' (0.75°) or less
225/50R18 -0°45' +/- 0°45' (-0.75° +/- 0.75°)


Camber (Unloaded Vehicle) (for TMMT Made):
Engine Tire Size Camber Inclination Right-left Difference

*1: except Rough Road Area Specification Vehicles

*2: for Rough Road Area Specification Vehicles

2ZR-FXE 215/60R17 -0°51' +/- 0°45' (-0.85° +/- 0.75°)*1
-0°43' +/- 0°45' (-0.72° +/- 0.75°)*2
0°45' (0.75°) or less
225/50R18 -0°51' +/- 0°45' (-0.85° +/- 0.75°)
M20A-FXS 215/60R17 -0°51' +/- 0°45' (-0.85° +/- 0.75°)
225/50R18 -0°51' +/- 0°45' (-0.85° +/- 0.75°)


HINT:

Camber is not adjustable. If the measurement is not within the specified range, inspect the suspension parts for damage and/or wear, and replace them if necessary.




INSPECT TOE-IN (REAR WHEEL ALIGNMENT)


NOTICE:

Inspect while the vehicle is unloaded.


a.

Bounce the vehicle up and down at the corners to stabilize the suspension.


b.

Release the parking brake and move the shift lever to N.


c.

Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step A)


d.
C188968C02
0.83,0.579 0.83,1.114 false 1.361,0.579 1.361,0.992 1.361,0.992 0.83,0.992 false 0.739,1.134 0.912,1.302 0.173,0.168 10 *a 2.432,1.697 2.607,1.858 0.176,0.161 10 *b 2.522,1.33 2.522,1.671 false
*a Tread Center Mark
*b Dimension B
V100135

Front of the Vehicle


Put tread center marks on the rearmost points of the rear wheels and measure the distance between the marks (dimension B).


e.

Slowly push the vehicle straight ahead to cause the rear wheels to rotate 180°. Use the rear tire valve as a reference point.

HINT:

Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from step A again.



f.
C188969C02
0.646,1.271 0.646,1.635 false 1.917,0.542 2.052,0.698 0.135,0.156 10 C 3.073,0.552 3.208,0.708 0.135,0.156 10 D 2.5,0.719 2.635,0.875 0.135,0.156 10 A 2.51,1.542 2.646,1.698 0.135,0.156 10 B 0.563,1.656 0.74,1.813 0.177,0.156 10 *a
*a Dimension A
V100135

Front of the Vehicle


Measure the distance between the tread center marks on the front of the rear wheels (dimension A).

Toe-in (Unloaded Vehicle) (for TMC Made):
Engine Tire Size Specified Condition
2ZR-FXE 215/60R17 C + D: 0°12' +/- 0°10' (0.20° +/- 0.17°)
B - A: 2.4 +/- 2.0 mm (0.0945 +/- 0.0787 in.)
225/50R18 C + D: 0°13' +/- 0°10' (0.22° +/- 0.17°)
B - A: 2.5 +/- 2.0 mm (0.0984 +/- 0.0787 in.)


Toe-in (Unloaded Vehicle) (for TMMT Made):
Engine Tire Size Specified Condition

*1: except Rough Road Area Specification Vehicles

*2: for Rough Road Area Specification Vehicles

2ZR-FXE 215/60R17 C + D: 0°16' +/- 0°10' (0.27° +/- 0.17°)*1
C + D: 0°11' +/- 0°10' (0.18° +/- 0.17°)*2
B - A: 3.1 +/- 2.0 mm (0.122 +/- 0.0787 in.)*1
B - A: 2.1 +/- 2.0 mm (0.0827 +/- 0.0787 in.)*2
225/50R18 C + D: 0°16' +/- 0°10' (0.27° +/- 0.17°)
B - A: 3.1 +/- 2.0 mm (0.122 +/- 0.0787 in.)
M20A-FXS 215/60R17 C + D: 0°16' +/- 0°10' (0.27° +/- 0.17°)
B - A: 3.1 +/- 2.0 mm (0.122 +/- 0.0787 in.)
225/50R18 C + D: 0°16' +/- 0°10' (0.27° +/- 0.17°)
B - A: 3.1 +/- 2.0 mm (0.122 +/- 0.0787 in.)


HINT:

Measure "B - A" only when "C + D" cannot be measured.


If the toe-in is not within the specified range, adjust it at the rear suspension toe adjust cam sub-assembly.