Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2016.10–2019.09
NM32K0E _51 Engine / Hybrid System _059761 HYBRID / BATTERY CONTROL _0292891 HYBRID CONTROL SYSTEM DE DETAILS F

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  DETAILS  INVERTER WITH CONVERTER  


CONSTRUCTION


a.

A compact, lightweight inverter with converter assembly, in which the MG ECU, inverter, boost converter and DC-DC converter are integrated, is used. The inverter and boost converter primarily consist of Intelligent Power Modules (IPMs), a reactor, and capacitor. The IPM is an integrated power module consisting of a signal processor, protective function processor, and Insulated Gate Bipolar Transistors (IGBTs).


b.

The inverter with converter assembly ensures heat dissipation through use of a water-cooled cooling system that is isolated from the engine cooling system.


c.

As a safety measure due to the use of high-voltage electricity, interlock switches are provided, which shut off the system main relays via the hybrid vehicle control ECU when the inverter terminal cover or connector cover assembly is removed, or the HV battery power cable connector is disconnected.

W132054C01
0.906,1.375 1.25,1.594 0.344,0.219 11 false *1 0.906,2.365 1.25,2.583 0.344,0.219 11 false *2
*1 Boost Converter / Inverter *2 DC-DC Converter
V100135

HV Coolant Outlet
V100136

HV Coolant Inlet



d.

The inverter uses the IPM to perform switching control. The IPMs for generator (MG1) and motor (MG2) each have a bridge circuit consisting of IGBTs. The IPM for generator (MG1) uses 6 IGBTs, one for each arm, and motor (MG2) uses 6 pairs of IGBTs, single in parallel for each arm.


e.

The boost converter uses a boost IPM to perform switching control, a reactor to act as an inductor, and a capacitor to accumulate and store electricity. The boost IPM uses IGBT2 for boosting voltage, and IGBT1 for reducing voltage.

W134591E01
1.813,1.927 2.365,0.615 2.365,0.615 2.531,0.615 true 3.635,1.927 4.229,0.969 4.229,0.969 4.396,0.969 true 3.979,2.51 5.042,2.146 5.042,2.146 5.208,2.146 true 1.26,6.167 1.427,6.167 1.427,6.167 1.573,5.917 true 1.5,1.51 1.656,1.708 0.156,0.198 10 false V 1.333,1.51 1.49,1.708 0.156,0.198 10 false U 1.625,1.51 1.781,1.708 0.156,0.198 10 false W 3.458,1.51 3.615,1.708 0.156,0.198 10 false W 3.313,1.51 3.469,1.708 0.156,0.198 10 false V 3.167,1.5 3.323,1.698 0.156,0.198 10 false U 1.458,1.104 2.063,1.313 0.604,0.208 10 false MG1 3.292,1.115 3.896,1.313 0.604,0.198 10 false MG2 2.594,0.51 4.208,0.729 1.615,0.219 10 false Inverter Current Sensor 4.479,0.885 6.094,1.104 1.615,0.219 10 false Inverter Current Sensor 5.271,2.073 6.885,2.292 1.615,0.219 10 false IGBT 1.208,3.833 2.823,4.052 1.615,0.219 10 false IPM for MG1 1.281,4.479 2.896,4.698 1.615,0.219 10 false Capacitor 3.031,3.979 4.646,4.198 1.615,0.219 10 false IPM for MG2 2.885,4.896 4.5,5.115 1.615,0.219 10 false Inverter 3.552,5.438 5.167,5.656 1.615,0.219 10 false MG ECU 5.115,5.406 6.521,5.938 1.406,0.531 10 false Hybrid Vehicle Control ECU 1.802,6.052 3.417,6.271 1.615,0.219 10 false Boost IPM 1.802,6.323 3.417,6.542 1.615,0.219 10 false Reactor 0.635,6.063 2.25,6.281 1.615,0.219 10 false IL Sensor 3.198,6.365 4.813,6.583 1.615,0.219 10 false DC-DC Converter 5.177,7.26 6.635,7.792 1.458,0.531 10 false Compressor with Motor Assembly 2.615,7.813 5,8.083 2.385,0.271 10 false Inverter with Converter Assembly 1.813,8.031 3.427,8.25 1.615,0.219 10 false HV Battery 0.552,6.813 2.167,7.031 1.615,0.219 10 false Boost Converter


f.

MG ECU

i.

The MG ECU is provided in the inverter with converter assembly. In accordance with the signals received from the hybrid vehicle control ECU, the MG ECU controls the inverter and boost converter in order to drive generator (MG1) or motor (MG2) or cause them to generate electricity.


ii.

The MG ECU transmits information that is required for vehicle control, such as the atmospheric pressure, inverter temperature and any failure information, to the hybrid vehicle control ECU. The MG ECU receives information that is required for controlling generator (MG1) and motor (MG2), such as the required motive force and the temperature of generator (MG1) and motor (MG2), from the hybrid vehicle control ECU.



g.

Temperature Sensor for Inverter with Converter Assembly

i.

For the inverter with converter assembly, there are 5 different temperature sensors; 2 of them are located at the IPMs for generator (MG1) and motor (MG2), 2 of them are located at the boost converter, and the remaining sensor is located at the HV coolant passage.


ii.

These sensors detect the temperatures at areas inside the inverter with converter assembly, and transmit that temperature information to the hybrid vehicle control ECU via the MG ECU. The hybrid vehicle control ECU optimizes the cooling system according to the temperature information, maintaining the output performance of the inverter with converter assembly.

W113314E07
1.292,0.958 2.125,1.167 0.833,0.208 10 false IPM for MG1 3.188,1.063 4.021,1.281 0.833,0.219 10 false IPM for MG2 5.094,2.042 6.208,2.281 1.115,0.24 10 false HV Coolant Flow 3.917,1.677 4.417,1.896 0.5,0.219 10 false Inverter 3.188,2.958 3.792,3.208 0.604,0.25 10 false MG ECU 0.833,3.292 1.563,3.531 0.729,0.24 10 false Boost IPM 0.563,3.667 1.594,3.917 1.031,0.25 10 false Boost Converter 5.594,3.167 6.542,3.802 0.948,0.635 10 false Hybrid Vehicle Control ECU 1.677,4.333 3.719,4.594 2.042,0.26 10 false Inverter with Converter Assembly 0.135,4.708 2.688,4.927 2.552,0.219 10 false *1: Temperature Sensor on IPM for MG1 0.135,5.031 2.688,5.292 2.552,0.26 10 false *2: Temperature Sensor on IPM for MG2 0.135,5.365 3.094,5.656 2.958,0.292 10 false *3: Temperature Sensor on Boost IPM (Upper) 3.438,4.708 6.396,5 2.958,0.292 10 false *4: Temperature Sensor on Boost IPM (Lower) 3.438,5.031 6.396,5.323 2.958,0.292 10 false *5: HV Coolant Temperature Sensor 4.177,2.385 4.385,2.604 0.208,0.219 10 false *5 2.292,2.198 2.469,2.375 0.177,0.177 10 false *4 1.313,2.198 1.49,2.375 0.177,0.177 10 false *3 1.802,1.438 1.979,1.615 0.177,0.177 10 false *1 3.729,1.427 3.906,1.604 0.177,0.177 10 false *2



h.

Inverter Current Sensor

i.

The inverter current sensors detect the amperage of the three-phase alternating current that actuates generator (MG1) and motor (MG2). This actual amperage is used as feedback by the MG ECU.


ii.

Current sensors are used for the current sent to the three-phase windings of generator (MG1) and motor (MG2). The current sensors are located in the inverter with converter assembly for the U, V and W phases of each generator and motor.

W134592E01
3.583,1.25 4.167,0.552 4.167,0.552 4.333,0.552 true 3.021,0.396 3.188,0.396 3.188,0.396 3.375,1.469 true 3.76,1.76 4.667,2.448 4.667,2.448 4.833,2.448 true 1.521,0.292 3.167,0.469 1.646,0.177 10 false Inverter Current Sensor 4.396,0.458 6.042,0.635 1.646,0.177 10 false Inverter Current Sensor 4.865,1 5.156,1.188 0.292,0.188 10 false U 4.344,1.74 4.531,1.917 0.188,0.177 10 false V 5.219,1.719 5.438,1.917 0.219,0.198 10 false W 5.271,1.365 6.917,1.542 1.646,0.177 10 false Generator/Motor 4.917,2.365 6.563,2.542 1.646,0.177 10 false Inverter Current Sensor 3.25,2.875 4.896,3.052 1.646,0.177 10 false MG ECU 2.031,2.385 3.677,2.563 1.646,0.177 10 false Inverter 0.521,4.25 3.927,4.521 3.406,0.271 10 false Characteristics of Inverter Current Sensor: 1.573,4.823 3.219,5 1.646,0.177 10 false 4.5 1.573,5.563 3.219,5.74 1.646,0.177 10 false 2.5 1.573,6.313 3.219,6.49 1.646,0.177 10 false 0.5 0.365,5.302 1.281,5.802 0.917,0.5 10 false Sensor Output Voltage (V) 1.531,6.667 2.01,6.833 0.479,0.167 10 false MG1 1.521,6.906 2,7.167 0.479,0.26 10 false MG2 4.083,6.625 4.563,6.792 0.479,0.167 10 false 0 1.99,6.917 2.469,7.083 0.479,0.167 10 false -375 1.969,6.667 2.448,6.833 0.479,0.167 10 false -200 5.979,6.667 6.458,6.833 0.479,0.167 10 false 200 5.979,6.917 6.458,7.083 0.479,0.167 10 false 375 3.865,7.25 5.51,7.427 1.646,0.177 10 false Current (A)



i.

IL Sensor

i.

Located after the reactor, the IL sensor detects the amperage of the current after voltage boost.


ii.

By sending the amperage as feedback to the hybrid vehicle control ECU, the fluctuation in boosted voltage (fluctuation in amperage) is suppressed. Due to this, the peak value of the boosted voltage is reduced, enabling a smaller capacitor to be used, and reducing the fluctuation in amperage contributes to mitigation of reactor characteristics and reduction of heat generated by components.