Home › Engine / Hybrid System › 2ZR-FXE (ENGINE MECHANICAL) › ENGINE UNIT
NM32K0E _51 Engine / Hybrid System _061022 2ZR-FXE ENGINE MECHANICAL _0299032 ENGINE UNIT DE DETAILS F

2ZR-FXE ENGINE MECHANICAL  ENGINE UNIT  DETAILS  CYLINDER BLOCK  


CONSTRUCTION


a.

A spiny type liner, which has an irregularly shaped outer casting surface, is used to enhance the adhesion between the liners and the aluminum of the cylinder block sub-assembly. The enhanced adhesion helps heat dissipation, resulting in a lower overall temperature and reduced heat deformation of the cylinder bores. A cylinder block sub-assembly with this type of liner cannot be rebored.


b.

V-shaped cooling passages are drilled between each bore to provide increased cooling to the upper part of the cylinder bore which is most susceptible to heat. This allows heat to be more evenly distributed around the cylinder bore walls. As a result, resistance to knocking has been enhanced, and by minimizing thermal deformation of the areas between each cylinder bore, friction has been also minimized ensuring high performance and fuel economy.

W130260C01
3.01,2.563 5.365,3.771 2.354,1.208 5.5,0.583 5.667,0.25 5.667,0.25 5.833,0.25 true 4.583,2.083 4.75,2.083 4.75,2.083 5.083,1.583 true 6.083,1.917 5.917,1.917 5.917,1.917 5.583,1.5 true 4.5,2.385 4.333,2.385 4.333,2.385 4.073,2.813 true 5.875,0.146 6.188,0.302 0.313,0.156 10 false *1 6.135,1.823 6.448,1.979 0.313,0.156 10 false *2 4.406,1.99 4.719,2.146 0.313,0.156 10 false *a 3.063,2.615 3.375,2.771 0.313,0.156 10 false *b 1.969,3.01 2.281,3.167 0.313,0.156 10 false A 1.677,0.781 1.99,0.938 0.313,0.156 10 false A 4.552,2.292 4.865,2.448 0.313,0.156 10 false *c
*1 Cylinder Block Sub-assembly *2 Spiny-type Liner
*a Irregularly shaped outer casting surface of liner *b A-A Cross Section
*c Drilled V-shaped Passage - -



c.

Through the use of an offset crankshaft, the centerline of the cylinder bores is shifted 8 mm (0.315 in.) towards the exhaust in relation to the centerline of the crankshaft. Thus, the side force (thrust) applied to the cylinder walls is reduced when maximum combustion pressure is applied. This contributes to fuel economy.

W101525C02
4.469,2.094 3.854,1.458 3.854,1.458 3.688,1.458 true 1.417,0.781 1.635,0.979 0.219,0.198 10 *a 1.781,3.344 1.979,3.542 0.198,0.198 10 *c 1.833,0.448 2.031,0.635 0.198,0.188 10 *b 4.406,0.208 4.646,0.406 0.24,0.198 10 *f 5.74,0.208 5.958,0.417 0.219,0.208 10 *f 3.521,1.365 3.719,1.552 0.198,0.188 10 *c 4.385,3.208 4.594,3.406 0.208,0.198 10 *d 5.896,3.229 6.146,3.448 0.25,0.219 10 *e
*a 8 mm (0.315 in.) *b Bore Centerline
*c Crankshaft Centerline *d Offset Crankshaft
*e Non-offset Crankshaft *f Maximum Pressure