Home › Vehicle Interior › PRE-COLLISION › PRE-COLLISION SYSTEM › 2018.05–2019.09
NM32K0E _58 Vehicle Interior _060726 PRE-COLLISION _0297886 PRE-COLLISION SYSTEM DE DETAILS F

PRE-COLLISION  PRE-COLLISION SYSTEM  DETAILS  INDICATOR LIGHT/WARNING LIGHT/MULTI DISPLAY  


OPERATION


a.

The combination meter assembly uses the multi-information display, PCS warning light and multi buzzer to provide the driver with pre-collision system warnings and indications.

Y232403C02
3.531,0.49 3.708,0.229 3.708,0.229 3.875,0.229 false 4.688,1.292 5.208,0.583 5.208,0.583 5.375,0.583 true 4.948,1.51 5.385,0.927 5.385,0.927 5.552,0.927 true 3.625,1.948 3.365,2.51 3.365,2.51 3.198,2.51 true 3.927,0.125 4.24,0.281 0.313,0.156 10 false *1 3,2.406 3.313,2.563 0.313,0.156 10 false *a 5.448,0.479 5.76,0.635 0.313,0.156 10 false *b 5.615,0.823 5.927,0.979 0.313,0.156 10 false *c
*1 Combination Meter Assembly - -
*a Multi-information Display *b PCS Warning Light
*c VSC OFF Indicator Light - -



b.

If the millimeter wave radar sensor assembly determines that the possibility of a collision is high, it sends a signal to the combination meter assembly. Upon receiving this signal, the combination meter assembly indicates a warning using the multi-information display. Details are indicated below.

When there is a high possibility of a collision
Multi-information Display PCS Warning Light
BRAKE! -


c.

When the system is not available, the following warning occurs to warn the driver.

When a system malfunction is detected
Multi-information Display Detail PCS Warning Light Multi Buzzer
Pre-Collision System Malfunction. Visit Your Dealer. This message appears when the forward recognition camera (camera sensor) or millimeter wave radar sensor assembly detects a system malfunction. Flashes Sounds once
Pre-Collision System Unavailable. Temperature or power supply of millimeter wave radar sensor assembly is abnormal. Illuminates -
Pre-Collision System Unavailable. Clean Sensor. Dirty center mark of upper radiator grille or millimeter wave radar sensor assembly. Illuminates -
Front Camera Unavailable. Temperature or power supply of forward recognition camera (camera sensor) is abnormal. Illuminates -
Front Camera Vision Blocked. Clean and Demist Windshield. Dirty or fog windshield glass over the forward recognition camera (camera sensor). Illuminates -

When the pre-collision system is turned OFF
Multi-information Display Detail PCS Warning Light Multi Buzzer
Pre-Collision System Off. Pre-collision system operation is disabled. Illuminates -

When in VSC OFF mode
Multi-information Display Detail PCS Warning Light VSC OFF Indicator Light
VSC Turned Off. Pre-Collision Brake System Unavailable. Pre-collision braking and pre-collision brake assist operation is disabled (a warning that occurs when there is a high possibility of a collision is still enabled). Illuminates Illuminates

HINT:

The message appears for 6 seconds on the multi-information display.



d.

The pre-collision system can be turned ON/OFF at setting display of the multi-information display.

i.

On the setting display screen, select PCS icon and then press on Enter/Set switch on the steering pad switch assembly.


ii.

Select [PCS] and then press on Enter/Set switch on the steering pad switch assembly. Each time is pressed, the system will be enabled/disabled.

Y208213C01
2.75,5.063 3.25,6.563 3.25,6.563 3.417,6.563 true 1.76,4.563 1.427,6.479 1.427,6.479 1.26,6.479 true 5.417,4.667 5.333,3.917 5.333,3.917 5.167,3.917 true 1.188,1.635 1.5,1.833 0.313,0.198 10 false *b 4.188,2.323 4.5,2.521 0.313,0.198 10 false *c 4.938,3.802 5.25,4 0.313,0.198 10 false *a 3.521,6.469 3.833,6.667 0.313,0.198 10 false *2 1.021,6.417 1.333,6.615 0.313,0.198 10 false *1
*1 Combination Meter Assembly *2 Steering Pad Switch Assembly
*a Enter/Set Switch *b PCS Warning Light
*c Multi-information Display - -


HINT:
·

If the system is disabled, the PCS warning light will turn on and a message will be displayed on the multi-information display.

·

The system is automatically enabled each time the power switch is turned to on (IG or READY).





e.

The pre-collision warning timing can be changed on setting display of the multi-information display.

i.

On the setting display screen, select PCS icon and then press on Enter/Set switch on the steering pad switch assembly.


ii.

Select [Sensitivity] and then press on Enter/Set switch on the steering pad switch assembly. Each Enter/Set switch is pressed, operation timing (Far/Middle/Near) of the pre-collision system will be changed.

Y208214C01
1,6.167 1.167,6.167 1.167,6.167 1.917,4.25 true 3.583,6.083 3.417,6.083 3.417,6.083 2.75,4.833 true 5.5,4.583 5.333,3.667 5.333,3.667 5.167,3.667 true 2.354,0.708 2.667,0.906 0.313,0.198 10 false *c 3.5,0.729 3.813,0.927 0.313,0.198 10 false *d 4.667,0.719 4.979,0.917 0.313,0.198 10 false *e 3.521,2.083 3.833,2.281 0.313,0.198 10 false *b 0.75,6.052 1.063,6.25 0.313,0.198 10 false *1 3.667,5.969 3.979,6.167 0.313,0.198 10 false *2 4.938,3.552 5.25,3.75 0.313,0.198 10 false *a
*1 Combination Meter Assembly *2 Steering Pad Switch Assembly
*a Enter/Set Switch *b Multi-information Display
*c Far *d Middle
*e Near - -