Home › Vehicle Interior › PRE-COLLISION › PRE-COLLISION SYSTEM › 2019.09–2020.08
NM32K0E _58 Vehicle Interior _060726 PRE-COLLISION _0297886 PRE-COLLISION SYSTEM CO CONTROL F

PRE-COLLISION  PRE-COLLISION SYSTEM  CONTROL  PRE-COLLISION CONTROL  


FUNCTION OF MAIN COMPONENTS


Item Function
Millimeter Wave Radar Sensor Assembly
·

Radiates millimeter wave forward, uses the reflected millimeter waves for detecting the presence of a vehicle ahead, the vehicle-to-vehicle distance, and the relative speed.

·

Determines whether a collision is imminent based on the information received from this sensor and forward recognition camera (camera sensor). It then outputs a brake assist standby request signal and pre-collision braking request signal if required.


Forward Recognition Camera (Camera Sensor)
·

Acquires a video of the area in front of the vehicle, and performs image processing to recognize obstacles or vehicles ahead, and then transmits this information to the millimeter wave radar sensor assembly.

·

Sounds the pre-collision city buzzer to warn the driver.

·

Controls the power supplied to the camera heater (forward recognition hood) when ambient air temperature is low.


Camera Heater (Forward Recognition Hood) Heats the sheet heater in accordance with the signals from the forward recognition camera (camera sensor), and prevents fogging of the windshield in the area in front of the forward recognition camera (camera sensor).
Brake Booster with Master Cylinder Assembly Skid Control ECU
·

Receives a brake assist standby request signal from the millimeter wave radar sensor assembly, and switches the brake assist to standby mode. When a master cylinder pressure signal is input, it activates the brake assist.

·

Receives a pre-collision brake request signal from the millimeter wave radar sensor assembly, and then applies the brakes.

·

Transmits vehicle speed signals to the millimeter wave radar sensor assembly.


Master Cylinder Pressure Sensor Detects the master cylinder pressure and transmits a signal to the skid control ECU.
Brake Booster Pump Assembly Pump Motor Receives an operation signal from the skid control ECU and generates hydraulic pressure for brake control.
Combination Meter Assembly PCS Warning Light
·

Illuminates to warn the driver in accordance with signals from the millimeter wave radar sensor assembly.

·

Illuminates when the system is malfunctioning or temporarily disabled.

·

Illuminates when the pre-collision system is not available due to when the pre-collision system is turned OFF or pre-collision braking and pre-collision brake assist operation are disabled using the VSC OFF switch.


VSC OFF Indicator Light Illuminates when in the VSC OFF mode.
Multi-information Display
·

Displays a warning message to inform or warn the driver of the system condition in accordance with signals from the millimeter wave radar sensor assembly.

·

Disables the pre-collision system operation when PCS OFF mode is selected on setting display screen.

·

Changes the pre-collision warning timing when Far/Middle/Near is selected on setting display screen.


Multi Buzzer Sounds to warn the driver in accordance with signals from the millimeter wave radar sensor assembly when the system is malfunctioning.
Hybrid Vehicle Control ECU
·

Transmits an accelerator pedal opening angle signal and shift position signal to the millimeter wave radar sensor assembly.

·

Controls hybrid system output based on the signal from the millimeter wave radar sensor assembly.


Airbag Sensor Assembly Detects the yaw rate and lateral/longitudinal deceleration of the vehicle and transmits the signal to the millimeter wave radar sensor assembly.
Air Conditioning Amplifier Assembly Transmits ambient temperature signals to the forward recognition camera (camera sensor).
Network Gateway ECU Relays and transmits each CAN communication data signal.
Spiral Cable with Sensor Sub-assembly Steering Angle Sensor Detects the steering direction and angle of the steering wheel and transmits the signal to the millimeter wave radar sensor assembly.
Pre-collision City Buzzer Sounds to warn the driver in accordance with signals from the forward recognition camera (camera sensor) when the system determines that the possibility of a frontal collision is high.
Electric Parking Brake Switch Assembly VSC OFF Switch Disables the pre-collision braking and pre-collision brake assist operation when the switch is turned on. The PCS warning light illuminates to show that the pre-collision braking and pre-collision brake assist operation is disabled. The pre-collision warning function can still operate.
Speed Sensor Detects the wheel speed and transmits signals to the skid control ECU.
Ambient Temperature Sensor (Thermistor Assembly) Detects ambient temperature and outputs it to the air conditioning amplifier assembly.
Stop Light Switch Assembly
·

Detects the depressing of the brake pedal and transmits a signal to the skid control ECU.

·

Illuminates the stop lights in accordance with the signals from the skid control ECU.


Accelerator Pedal Sensor Assembly Detects the amount of pedal effort applied to the accelerator pedal and transmits the signal to the hybrid vehicle control ECU.
Shift Lever Position Sensor Detects the shift position and sends the signal to the hybrid vehicle control ECU.
Steering Pad Switch Assembly Switch the display of multi-information display within combination meter assembly.


FUNCTION


a.

The pre-collision system uses a millimeter wave radar sensor assembly and forward recognition camera (camera sensor) to detect vehicles and pedestrians in front of your vehicle.


b.

When the system determines that the possibility of a frontal collision with a vehicle or pedestrian is high, a warning operates to urge the driver to take evasive action and the potential brake pressure is increased to help the driver avoid the collision.


c.

If the system determines that the possibility of a frontal collision with a vehicle or pedestrian is extremely high, the brakes are automatically applied to help avoid the collision or help reduce the impact of the collision.

i.

Pre-collision warning

·

When the system determines that the possibility of a frontal collision is high, a pre-collision city buzzer will sound and a warning message will be displayed on the multi-information display to urge the driver to take evasive action.



ii.

Pre-collision brake assist

·

When the system determines that the possibility of a frontal collision is high, the system applies greater braking force in relation to how strongly the brake pedal is depressed.



iii.

Pre-collision braking

·

When the system determines that the possibility of a frontal collision is high, the system warns the driver. If the system determines that the possibility of a frontal collision is extremely high, the brakes are automatically applied to help avoid the collision or help reduce the collision speed.





OPERATING CONDITION


a.

The pre-collision system is enabled and the system determines that the possibility of a frontal collision with a vehicle or pedestrian is high. Each function is operational at the following speeds:

i.

Pre-collision warning:

·

Vehicle speed is between approximately 10 and 180 km/h (7 and 110 mph). (For detecting a pedestrian, vehicle speed is between approximately 10 and 80 km/h (7 and 50 mph).)

·

The relative speed between your vehicle and the vehicle or pedestrian ahead is approximately 10 km/h (7 mph) or more.



ii.

Pre-collision brake assist:

·

Vehicle speed is between approximately 30 and 180 km/h (20 and 110 mph). (For detecting a pedestrian, vehicle speed is between approximately 30 and 80 km/h (20 and 50 mph).)

·

The relative speed between your vehicle and the vehicle or pedestrian ahead is approximately 30 km/h (20 mph) or more.



iii.

Pre-collision braking:

·

Vehicle speed is between approximately 10 and 180 km/h (7 and 110 mph). (For detecting a pedestrian, vehicle speed is between approximately 10 and 80 km/h (7 and 50 mph).)

·

The relative speed between your vehicle and the vehicle or pedestrian ahead is approximately 10 km/h (7 mph) or more.




b.

The system may not operate in the following situations:

i.

If a 12-volt battery terminal has been disconnected and reconnected and then the vehicle has not been driven for a certain amount of time.


ii.

If the shift lever is in R


iii.

If VSC is disabled (only the pre-collision warning function will be operational)



c.

Cancelation of the pre-collision braking

i.

If either of the following occur while the pre-collision braking function is operating, it will be canceled:

·

The accelerator pedal is depressed strongly.

·

The steering wheel is turned sharply or abruptly.



ii.

If the vehicle is stopped by the operation of the pre-collision braking function, the pre-collision braking function operation will be canceled after approximately 2 seconds. Depress the brake pedal as necessary.



d.

Conditions under which the system may operate even if there is no possibility of a collision

i.

In some situations such as the following, the system may determine that is a possibility of a frontal collision and operate.

·

When passing a vehicle or pedestrian

·

When changing lanes while overtaking a vehicle ahead

·

When overtaking a vehicle ahead that is changing lanes

·

When overtaking a vehicle ahead that is making a right/left turn

Y191503

·

When passing a vehicle in an oncoming lane that is stopped to make a right/left turn

Y191504

·

When driving on a road where relative location to vehicle ahead in an adjacent lane may change, such as on a winding road

Y191506

·

When rapidly closing on a vehicle ahead

·

If the front of the vehicle is raised or lowered, such as when the road surface is uneven or undulating

·

When approaching objects on the roadside, such as guardrails, utility pales, trees, or walls

·

When there is a vehicle, pedestrian, or object by the roadside at the entrance of a curve

Y186309

·

When driving on a narrow path surrounded by a structure, such as in a tunnel or on an iron bridge

·

When there is a metal object (manhole cover, steel plate, etc.), steps, or a protrusion on the road surface or roadside

·

When a crossing pedestrian approaches very close to the vehicle

Y186316

·

When passing through a place with a low structure above the road (low ceiling, traffic sign, etc.)

Y186313

·

When passing under an object (billboard, etc.) at the top of an uphill road

Y190952

·

When rapidly closing on an electric toll gate barrier, parking area barrier, or other barrier that opens and closes

·

When using an automatic car wash

·

When driving through or under objects that may contact the vehicles, such as thick grass, tree branches, or a banner

Y186314

·

When the vehicle is hit by water, snow, dust, etc. from a vehicle ahead

·

When driving through steam or smoke

·

When there are patterns or paint on the road or a wall that may be mistaken for a vehicle or pedestrian

·

When driving near an object that reflects radio waves, such as a large truck or guardrail

·

When driving near a TV tower, broadcasting station, electric power plant, or other location where strong radio waves or electrical noise may be present





SYSTEM CONTROL


a.

Pre-collision Brake Assist

i.

While the pre-collision system has determined that there is a high possibility of a collision, brake hydraulic pressure assistance is performed when the driver depresses the brake pedal. Also, the amount of brake hydraulic pressure assistance increases further when the system determines that there is an even higher possibility of a collision.

Y191467E01
1.031,0.219 2.354,0.75 1.323,0.531 10 false Possibility of collision determined 2.531,0.229 3.302,0.781 0.771,0.552 10 false Brake pedal depressed 3.594,0.229 4.708,0.75 1.115,0.521 10 false High possibility of collision determined 5.094,0.229 5.719,0.771 0.625,0.542 10 false Collision 0.781,1.427 1.677,1.688 0.896,0.26 10 false Normal Driving 1.948,1.427 2.74,1.813 0.792,0.385 10 false Operation on Standby 2.906,1.427 4.208,1.885 1.302,0.458 10 false Brake Fluid Pressure Increased 4.438,1.438 5.167,2.083 0.729,0.646 10 false Brake Fluid Pressure Further Increased 0.063,0.583 0.958,0.844 0.896,0.26 10 false Elapsed Time 2.917,2.927 4.281,3.604 1.365,0.677 10 false Brake fluid pressure is increased as soon as the brake pedal is depressed 5.208,3.448 7.063,3.979 1.854,0.531 10 false Additional brake fluid pressure when possibility of collision is high 5.208,4.417 7.156,4.656 1.948,0.24 10 false Additional Brake Fluid Pressure 5.24,4.844 7.146,5.094 1.906,0.25 10 false Normal Brake Fluid Pressure 0.01,4.521 0.729,4.865 0.719,0.344 10 false Brake Fluid Pressure 0.094,6.24 0.635,6.802 0.542,0.563 10 false Vehicle Speed 5.271,5.823 7.125,6.073 1.854,0.25 10 false Normal Braking 5.25,6.51 7.052,6.875 1.802,0.365 10 false Deceleration when possibility of collision is high 2.948,6.271 4.177,6.719 1.229,0.448 10 false Pre-collision Brake Assist



b.

Pre-collision Braking

i.

When the pre-collision system detects an object such as a vehicle or road structure in front of the vehicle and determines that the possibility of a collision is high, the system displays a warning message on the multi-information display, and sounds the pre-collision city buzzer to warn the driver.


ii.

When the pre-collision system determines high possibility of collision, the system performs pre-collision braking control.

Y228298E01
0.875,0.365 2.198,0.854 1.323,0.49 10 false Possibility of collision determined* 2.458,0.365 3.917,0.802 1.458,0.438 10 false High possibility of collision determined 4.167,0.365 4.948,0.875 0.781,0.51 10 false Unavoidable collision 5.604,0.365 6.167,0.813 0.563,0.448 10 false Collision 0.031,1.083 0.552,1.521 0.521,0.438 10 false Elapsed Time 0.573,1.719 1.5,2.219 0.927,0.5 10 false Normal Driving 1.625,1.719 5.667,2.115 4.042,0.396 10 false Pre-collision Warning (Display "BRAKE!" and Buzzer Sounds) 3.24,2.656 4.563,3.146 1.323,0.49 10 false Pre-collision Braking 6.021,3.813 7.125,4.292 1.104,0.479 10 false Speed Reduction 0.042,3.75 0.531,4.229 0.49,0.479 10 false Vehicle Speed 0.198,4.833 6.938,5.323 6.74,0.49 10 false *: Warning Timing can be selected as "Far", "Middle" or "Near" by operating the Steering Pad Switch Assembly and Multi-information Display




DIAGNOSIS


a.

Initial Check

i.

The millimeter wave radar sensor assembly performs an initial check on the system for approximately 3 seconds after the power switch has been turned to on (IG).



b.

Monitor Function

i.

After completing the initial check, the pre-collision system becomes ready to operate. During this time, the millimeter wave radar sensor assembly periodically monitors the system for any malfunctions.



c.

Diagnostic Trouble Code (DTC)

i.

If the millimeter wave radar sensor assembly detects a malfunction in the pre-collision system, it stores a Diagnostic Trouble Code (DTC) in memory.