Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM › from 2019.09
NM32K0E _56 Audio / Visual / Telematics _084496 TELEMATICS _0407115 TELEMATICS SYSTEM CO CONTROL F

TELEMATICS  TELEMATICS SYSTEM  CONTROL  eCall SERVICE  


FUNCTION OF MAIN COMPONENTS


a.

The main components in the eCall system have the following functions:

Component Function

*1: Models with 6-speaker sound system

*2: Models with 9-speaker sound system

Map Light Assembly Manual (SOS) Switch (Mayday Switch Assembly) When pressed, allows the driver to connect to and communicate with the PSAP as an emergency assistance button (SOS) service.
Manual (SOS) Switch Indicator Green
·

Turns on when the system is operating normally within the service area.

·

Blinks during a call and turns off when the system is malfunctioning.


Red
·

Illuminates to warn the user when a malfunction occurs in the system.

·

Turns off when the system is operating normally.


Communication Telematics Box
·

Houses the microphones and speaker.

·

Receives the user's voice through the microphones.

·

Outputs the operators voice of PSAP through the speaker.


DCM (Telematics Transceiver)
·

Connects to the PSAP and allows the driver to speak with the call center operator when the automatic emergency call service or the manual emergency call service is active.

·

The cellular phone module makes or receives calls.

·

The DCM (telematics transceiver) receives signals from the GNSS antenna, calculates the position of the vehicle and transmits it to the PSAP.

·

Controls the on/off and blinking actions of the manual (SOS) switch indicator.

·

Dims the manual (SOS) switch indicator when the taillight relay on signal is received.

·

When communicating with PSAP, sends the users voice picked up by the communication telematics box (microphones), and outputs the operators voice through the communication telematics box (speaker).


Back-up Battery (Mobilephone Battery) Is built into the DCM (telematics transceiver) and supplies power to the DCM (telematics transceiver) when the automatic emergency call service is activated and the vehicle battery cannot supply power.
Roof Antenna Assembly Telephone Antenna Is for a cellular phone antenna which is compatible with the transmission and reception of frequency bands of cellular phones. It transmits signals from the DCM (telematics transceiver) and receives signals from the call center.
GNSS Antenna Receives the signals from GNSS satellites and transmits these signals to the DCM (telematics transceiver).
Airbag Sensor Assembly Sends an activation signal to the DCM (telematics transceiver) when the airbags deploy. (An automatic emergency call service is made.)
Radio and Display Receiver Assembly
·

Receives microphone voice signals from DCM (telematics transceiver).

·

Receives the mute signal from the DCM (telematics transceiver) to mute any audio sound.*1


Main Body ECU (Multiplex Network Body ECU) Sends the taillight relay on signal to the DCM (telematics transceiver).
Stereo Component Amplifier Assembly*2 Receives the mute signal from the DCM (telematics transceiver) to mute any audio sound.
Combination Meter Assembly Sends the vehicle speed signal to the DCM (telematics transceiver), radio and display receiver.



FUNCTION


a.

Automatic Emergency Call Service

·

If any of the airbags are deployed due to a serious collision, the DCM (telematics transceiver) receives the deployment signal from the airbag sensor assembly. After receiving the deployment signal, the DCM (telematics transceiver) automatically makes an emergency call and transmits the vehicle location and user information to the PSAP closest to the vehicle.

·

The system is then automatically connected to a PSAP and the user can talk to a PSAP operator. The PSAP operator contacts the emergency services when the user is unable to answer.

Automatic Emergency Call Service Image
Y178729C01
1.719,1.448 2.031,1.646 0.313,0.198 10 false *a 3.75,1.323 4.063,1.521 0.313,0.198 10 false *b 5.615,1.198 5.927,1.396 0.313,0.198 10 false *c
*a Airbag Deployment or Collision Detection *b Public Safety Answering Point (PSAP)
*c Ambulance - -




b.

Manual Emergency Call Service

·

By pushing the manual (SOS) switch (mayday switch assembly) during an on-road emergency, the DCM (telematics transceiver) transmits the vehicle location and user information, and calls to the PSAP closest to the vehicle.

·

The PSAP operator determines the level of the emergency based on the vehicle location and from the conversation with the user, and contacts the emergency services if necessary.

Manual Emergency Call Service Image
Y178730C01
1.948,1.365 2.26,1.563 0.313,0.198 10 false *1 4.906,1.354 5.219,1.552 0.313,0.198 10 false *a
*1 Manual (SOS) Switch (Mayday Switch Assembly) - -
*a Public Safety Answering Point (PSAP) - -




c.

eCall Mode

·

There are 2 modes depending on the vehicle status.

Mode Type Available Services

*: Once activation has started, the system performs the activation process repeatedly until completion. To avoid transmitting radio waves unnecessarily, make sure to perform activation in an eCall service support area.

Shipping Mode
·

Mode the DCM (telematics transceiver) is in from the factory and during shipping.

·

The power switch can be turned on (IG) without transmitting radio waves.

·

The system will activate if the manual (SOS) switch (mayday switch assembly) is pushed and held for 3 seconds when in an eCall service support area in a mobile phone reception area.*


Live Mode
·

When activation has completed, the system changes to live mode.

·

All functions of eCall can be utilized in live mode.






DIAGNOSIS


a.

If there is a malfunction in the system, the DCM (telematics transceiver) stores Diagnostic Trouble Codes (DTCs) in its memory. For details, refer to the Repair Manual.