Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM (for NICKEL METAL HYDRIDE BATTERY) › from 2019.09
NM32K0E _51 Engine / Hybrid System _059761 HYBRID / BATTERY CONTROL _0407472 HYBRID BATTERY SYSTEM(for NICKEL METAL HYDRIDE BATTERY) GE GENERAL F

HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM(for NICKEL METAL HYDRIDE BATTERY)  GENERAL  GENERAL  


OUTLINE


a.

HV Battery

i.

A Nickel Metal Hydride (Ni-MH) battery has been provided.


ii.

A small and high-efficiency hybrid battery has been installed under the rear seat.


iii.

The hybrid battery location increases luggage space capacity and contributes to excellent handling stability due to a lower center of gravity.




SPECIFICATION


a.

HV Battery

Item Specification

*1: Models with 2ZR-FXE Engine

*2: Models with M20A-FXS Engine

Type Nickel Metal Hydride (Ni-MH) Battery
Cell Quantity 168 Cells (6 Cells x 28 Modules)*1
180 Cells (6 Cells x 30 Modules)*2
Nominal Voltage V 201.6*1
216*2
Battery Capacity (3HR) Ah 6.5



MAIN FEATURES


a.

Cooling System

i.

To ensure the proper performance of the HV battery while it generates heat during repetitive charge and discharge cycles, a dedicated cooling system is used for the HV battery.


ii.

Air is taken in from the trim located under the right rear seating position for more efficient cooling.


iii.

An air filter has been provided on the cooling air intake bezel.

NOTICE:
·

There is an air intake vent under the right side of the rear seat for the purpose of cooling the hybrid battery.

If the vent becomes blocked, the hybrid battery may overheat, charging / discharging of the hybrid battery may become limited.

·

Clean the air intake vent regularly using a vacuum cleaner to prevent the hybrid battery from overheating.

·

Do not allow liquid or foreign materials to enter the air intake vent as this may cause a short circuit and damage the hybrid battery.

·

Do not carry large amounts of water such as water cooler bottles in the vehicle. If water spills onto the hybrid battery, the battery may be damaged.




iv.

The cooling pathways have been optimized to achieve both a quiet cabin and ample cooling.

Models with 2ZR-FXE Engine
W141429C01
4.833,1.781 5.583,0.531 5.583,0.531 5.75,0.531 true 1.24,5.063 1.49,4.646 1.49,4.646 1.656,4.646 true 5.333,4.865 5.583,4.448 5.583,4.448 5.75,4.448 true 1.469,3.854 1.635,3.854 1.635,3.854 2.135,3.021 true 3.948,5.104 4.344,4.438 4.344,4.438 4.51,4.438 true 1.281,3.75 1.594,3.906 0.313,0.156 10 false *1 5.823,0.427 6.135,0.583 0.313,0.156 10 false *2 4.583,4.333 4.896,4.49 0.313,0.156 10 false *3 4.115,3.083 4.281,3.25 0.167,0.167 10 true *a 3.667,1.385 3.833,1.552 0.167,0.167 10 true *b 2.333,1.833 2.5,2 0.167,0.167 10 true *b 5.823,4.344 6.135,4.5 0.313,0.156 10 false *2 1.729,4.542 2.042,4.698 0.313,0.156 10 false *1
*1 Battery Cooling Blower Assembly *2 HV Battery Assembly
*3 Hybrid Battery Module - -
*a to Cabin *b to Luggage Room
V100135

Cooling Air Flow - -


Models with M20A-FXS Engine
W142847C01
4.417,1.75 5.25,0.333 5.25,0.333 5.417,0.333 true 1.417,5.417 1.917,4.583 1.917,4.583 2.083,4.583 true 1.448,3.844 1.615,3.844 1.615,3.844 2.115,3.01 true 4.917,5.583 5.417,4.75 5.417,4.75 5.583,4.75 true 1.25,3.74 1.563,3.896 0.313,0.156 10 false *1 5.49,0.229 5.802,0.385 0.313,0.156 10 false *2 5.656,4.646 5.969,4.802 0.313,0.156 10 false *3 2.156,4.479 2.469,4.635 0.313,0.156 10 false *1
*1 Battery Cooling Blower Assembly *2 HV Battery Assembly
*3 Hybrid Battery Module - -
V100135

Cooling Air Flow - -




b.

Service Plug Grip

i.

By removing the service plug grip before performing any inspection or service, the high-voltage circuit is shut off, thus ensuring safety during service.

CAUTION:
·

A charge remains in the high-voltage capacitor in the inverter with converter assembly after the high-voltage circuits are cut off. When servicing a hybrid vehicle, after removing the service plug grip, wait at least 10 minutes to allow the capacitor to discharge before beginning work.

·

For further details on how to handle the service plug grip and other safety cautions, refer to the Repair Manual.



NOTICE:
·

The service plug grip should never be removed when the system is in the on (READY) state.

·

After removing the service plug grip, turning the power switch (push start switch) on (READY) may cause a malfunction. Do not turn the power switch (push start switch) on (READY) unless instructed by the Repair Manual.




ii.

The service plug grip is connected in the battery module circuit and is used for manually shutting off the high-voltage circuit. This provides safety during service.


iii.

An interlock switch is provided on the service plug grip. When the grip section is unlocked, the interlock switch is turned off and the hybrid vehicle control ECU shuts off the system main relays. However, to ensure safety, make sure to turn the power switch (push start switch) off before removing the service plug grip.

W134573C01
2.417,6.26 2.427,5.583 true 4.458,2.281 5.521,1.833 5.521,1.833 5.75,1.833 true 5.167,2.667 5.667,2.667 true 2.354,6.281 2.583,6.448 0.229,0.167 10 false *1 5.708,2.583 6.021,2.74 0.313,0.156 10 false *2 5.771,4.573 6,4.729 0.229,0.156 10 false *4 5.802,1.75 6.031,1.917 0.229,0.167 10 false *1 5.667,5.927 5.896,6.083 0.229,0.156 10 false *3 0.708,5.438 0.938,5.594 0.229,0.156 10 false *3 4.99,6.333 5.219,6.5 0.229,0.167 10 false *1
*1 Service Plug Grip *2 Battery Service Hole Cover
*3 Interlock Switch *4 HV Battery