Home › Engine / Hybrid System › M20A-FXS (ENGINE MECHANICAL) › ENGINE UNIT › from 2019.09
NM32K0E _51 Engine / Hybrid System _084656 M20A-FXS ENGINE MECHANICAL _0407653 ENGINE UNIT GE GENERAL F

M20A-FXS ENGINE MECHANICAL  ENGINE UNIT  GENERAL  GENERAL  


OUTLINE


a.

The M20A-FXS engine is an in-line 4-cylinder, 2.0 liter, 16 valve DOHC engine.


b.

The engine adopts the Dual Variable Valve Timing-intelligent (Dual VVT-i) system which realizes optimal valve timing by using electric motors to actuate the intake camshaft actuators and engine oil pressure to actuate the exhaust camshaft actuators. In addition, this engine uses a high-expansion ratio Atkinson cycle, Direct injection 4-stroke gasoline engine Superior version (D-4S) system, Direct Ignition System (DIS), Electronic Throttle Control System-intelligent (ETCS-i) and Exhaust Gas Recirculation (EGR) system employing a highly efficient EGR cooler. Thus, improved engine performance, quietness, fuel economy and cleaner emissions have been achieved.



SPECIFICATION


Item Specification
Engine Type M20A-FXS
No. of Cyls. & Arrangement 4-cylinder, In-line
Valve Mechanism 16-valve DOHC, Chain Drive
(with VVT-iE and VVT-i)
Combustion Chamber Pentroof Type
Flow of Intake and Exhaust Gasses Cross-flow
Fuel System Sequential Multiport Fuel Injection (SFI) D-4S
Ignition System Direct Ignition System (DIS)
Displacement cm3 (cu. in.) 1987 (121.2)
Bore x Stroke mm (in.) 80.5 x 97.6 (3.17 x 3.84)
Compression Ratio 14.0 : 1
Max. Output (EEC) kW@rpm 112@6000
Max. Torque (EEC) N*m@rpm 190@4400 to 5200
Valve Timing Intake Open -30° to 25° BTDC
Closed 110° to 55° ABDC
Exhaust Open 3° to 44° BBDC
Closed 41° to 0° ATDC
Spark Plug Type DENSO Made FC16HR-Q8
Plug Gap mm (in.) 0.7 to 0.8 (0.0276 to 0.0315)
Firing Order 1 - 3 - 4 - 2
Research Octane Number (RON) 95 or higher
Emission Regulation*1 EURO 6d
Engine Service Mass*2 (Reference) kg (lb.) 113 (249.1)

HINT:

*1: Emission regulations differ by country and region.

*2: The figure shown is the weight of the part without coolant and oil.



MAIN FEATURES


a.

The M20A-FXS engine has achieved the following through the use of the items listed in the table below.

i.

High performance and reliability


ii.

Low noise and vibration


iii.

Lightweight and compact design


iv.

Good serviceability


v.

Clean emissions and improved fuel economy

Item i ii iii iv v
The high-expansion ratio Atkinson cycle is adopted. ○ - - - ○
Engine Proper An aluminum cylinder block sub-assembly is used. - - ○ - -
Spiny-type liners are used in the cylinder bores. ○ - - - -
A cylinder block water jacket spacer is used. ○ - - - ○
The piston skirt is coated with resin. ○ ○ - - ○
An offset crankshaft is used. ○ ○ - - ○
Laser cladded valve seats are used for the intake side. ○ - - - ○
A chain cover that consists of the timing chain cover assembly and No. 2 timing chain cover assembly is used. ○ - - - -
Bolts with smaller heads than standard bolts of the same thread diameter are used. ○ - ○ - -
Valve Mechanism The Variable Valve Timing-intelligent by Electric motor (VVT-iE) system is used for the intake camshaft sub-assembly. ○ - - - ○
The Variable Valve Timing-intelligent (VVT-i) system is used for the exhaust camshaft sub-assembly. ○ - - - ○
A chain sub-assembly and No. 1 chain tensioner assembly are used. - ○ - ○ -
Valve lash adjuster assemblies are used. ○ ○ - ○ -
No. 1 valve rocker arm sub-assemblies are used. ○ - - - ○
Lubrication System A cartridge type oil filter sub-assembly is used. - - - ○ -
An electronically controlled variable displacement oil pump is used. ○ - - - ○
An engine oil level sensor is used. - - - - ○
An engine oil cooler (oil cooler assembly) is used. ○ - - - -
Cooling System TOYOTA Genuine Super Long Life Coolant (SLLC) is used. - - - ○ -
A variable cooling control system is used. ○ - - - ○
An electric engine water pump is used. - - - - ○
Intake and Exhaust System An intake manifold made of plastic is used. - ○ ○ - -
A linkless type throttle body with motor assembly is used. - - ○ ○ -
A stainless steel exhaust manifold is used. - - ○ - -
Emission Control System A step motor type Exhaust Gas Recirculation (EGR) valve is used. ○ - - - ○
A water-cooled type Exhaust Gas Recirculation (EGR) cooler is used. ○ - - - ○
An ultra thin-wall, high-cell density ceramic type Three-Way Catalytic converter (TWC) is used. - - - - ○
Fuel System A Direct injection 4-stroke gasoline engine Superior version (D-4S) system is used. ○ - - - ○
A fuel returnless system is used. - - ○ ○ ○
Quick connectors are used to connect the fuel hoses with the fuel pipes. - - - ○ -
10-hole type low pressure port fuel injector assemblies are used. ○ - - - ○
6-hole type high pressure direct fuel injector assemblies are used. ○ ○ - - ○
Ignition System The Direct Ignition System (DIS) is used. ○ - - ○ ○
Long-reach type iridium-tipped spark plugs are used. ○ - - ○ ○
Engine Control System Magnetic Resistance Element (MRE) type camshaft position sensors and crank position sensor are used. ○ - - - ○
The Electronic Throttle Control System-intelligent (ETCS-i) is used. ○ - - - ○
An evaporative emission control system is used. - - - - ○

HINT:

○: Applicable

-: Not applicable




b.

Location of small-head bolts

W140856

W140857

W140859