Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HV BATTERY THERMISTOR › 2016.10–2019.09
RM32K0E _51 Engine / Hybrid System _059620 HYBRID / BATTERY CONTROL _0292493 HV BATTERY THERMISTOR A

HYBRID / BATTERY CONTROL  HV BATTERY THERMISTOR  INSTALLATION  


PROCEDURE

Hide G9282 1.INSTALL HYBRID BATTERY THERMISTOR

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.
A378137C02
0.354,1.042 0.51,0.198 0.51,0.198 0.781,0.198 true 1.667,1.24 1.854,0.24 1.854,0.24 2.125,0.24 true 2.625,2.021 2.865,2.021 2.865,2.021 3.042,1.292 true 0.781,0.115 1.01,0.333 0.229,0.219 10 true *a 2.125,0.167 2.354,0.385 0.229,0.219 10 true *b 2.375,1.938 2.604,2.125 0.229,0.188 10 true *c
*a 1st Module from the HV Battery Junction Block Assembly Side
(Wire harness color: Blue)
*b 14th Module from the HV Battery Junction Block Assembly Side
(Wire harness color: White)
*c 28th Module from the HV Battery Junction Block Assembly Side
(Wire harness color: Red)


Engage the 3 claws of the hybrid battery thermistor (sensor portions) to install the hybrid battery thermistor to the HV battery.

HINT:

Install each hybrid battery thermistor (sensor portion) to the appropriate location shown in the illustration.



b.
A375923C02
0.646,1.156 0.781,0.198 0.781,0.198 1,0.198 true 1.229,1.208 1.396,2.052 1.396,2.052 1.583,2.052 true 1.854,1.177 1.99,0.219 1.99,0.219 2.208,0.219 true 2.656,1.188 2.802,2.031 2.802,2.031 2.979,2.031 true 1.031,0.146 1.26,0.333 0.229,0.188 10 true *a 1.594,1.969 1.823,2.156 0.229,0.188 10 true *b 2.208,0.167 2.438,0.354 0.229,0.188 10 true *c 2.979,1.948 3.208,2.135 0.229,0.188 10 true *d
*a 4th Module from the HV Battery Junction Block Assembly Side
*b 10th Module from the HV Battery Junction Block Assembly Side
*c 16th Module from the HV Battery Junction Block Assembly Side
*d 24th Module from the HV Battery Junction Block Assembly Side


Engage the 4 clamps in the locations shown in the illustration.


c.

Connect the battery voltage sensor connector.


d.

Engage the clamp.


e.
A376384C02
1.125,0.604 1.188,0.292 1.188,0.292 1.375,0.292 false 2.75,0.583 2.813,0.271 2.813,0.271 3,0.271 false 2.281,0.208 2.469,0.208 false 0.531,0.427 0.781,0.427 false 2.104,0.156 2.417,0.354 0.313,0.198 10 false *1 0.375,0.365 0.688,0.563 0.313,0.198 10 false *1 1.427,0.229 1.74,0.427 0.313,0.198 10 false *a 3.042,0.188 3.354,0.385 0.313,0.198 10 false *a
*1 No. 1 Hybrid Battery Packing
*a Tape


Engage the 2 claws to install the No. 1 hybrid battery packing to the HV battery.

NOTICE:

Align each tape on the hybrid battery thermistor with the edge of the No. 1 hybrid battery packing as shown in the illustration and then engage the 2 claws to install the No. 1 hybrid battery packing to the HV battery.



f.

Engage the clamp.


Hide G92D1 2.INSTALL NO. 1 HYBRID BATTERY INTAKE DUCT

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Engage the claw to install the No. 1 hybrid battery intake duct to the HV battery.


b.

Engage the claw of hybrid battery thermistor (sensor portion) to connect the hybrid battery thermistor to the No. 1 hybrid battery intake duct.


Hide G920Q 3.INSTALL NO. 1 HYBRID BATTERY SHIELD SUB-ASSEMBLY

CAUTION:

Wear insulated gloves.


a.

Pull back the No. 2 hybrid battery shield sub-assembly to install the No. 1 hybrid battery shield sub-assembly to the HV battery.

HINT:

Pull back the No. 2 hybrid battery shield sub-assembly until there is sufficient clearance for the stud bolt of the No. 1 hybrid battery shield sub-assembly.



b.

Install the 4 nuts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 4.INSTALL HV BATTERY JUNCTION BLOCK ASSEMBLY