Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2016.10–2020.08
RM32K0E _57 Power Source / Network _059857 NETWORKING _0293867 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Steering Angle Sensor Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Steering Angle Sensor Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "Spiral cable (Steering Angle Sensor)" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "Spiral cable (Steering Angle Sensor)" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Spiral cable (Steering Angle Sensor)" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Steering Angle Sensor Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Steering sensor branch line or connector

·

Power source circuit of steering sensor

·

Steering sensor ground circuit

·

Steering sensor



WIRING DIAGRAM

for LHD



C366179E11
1.677,0.531 1.833,0.729 0.156,0.198 10 false 5 1.677,1.073 1.917,1.271 0.24,0.198 10 false 15 0.26,1.573 0.75,1.771 0.49,0.198 10 false F116 0.26,1.729 2.344,1.896 2.083,0.167 10 false No. 4 CAN Junction Connector 5.438,0.51 5.594,0.708 0.156,0.198 10 false 3 5.448,1.063 5.604,1.26 0.156,0.198 10 false 2 5.677,0.646 6.25,0.813 0.573,0.167 10 false CANH 5.667,1.177 6.24,1.344 0.573,0.167 10 false CANL 5.677,2.26 6.25,2.427 0.573,0.167 10 false IG1 5.677,2.781 6.25,2.948 0.573,0.167 10 false BAT 5.677,3.302 6.25,3.469 0.573,0.167 10 false ESS 5.604,3.698 6.177,3.865 0.573,0.167 10 false F69 5.615,3.875 6.688,4.125 1.073,0.25 10 false Steering Sensor 4.146,2.927 5.396,3.177 1.25,0.25 10 false ECU-DCC NO. 1 4.188,2.375 5.438,2.625 1.25,0.25 10 false ECU-IG1 NO. 2 2.052,2.208 3.552,2.458 1.5,0.25 10 false from IG1-NO. 1 Relay 2.042,2.74 3.542,2.99 1.5,0.25 10 false from Auxiliary Battery 5.458,2.115 5.615,2.313 0.156,0.198 10 false 4 5.458,2.656 5.615,2.854 0.156,0.198 10 false 5 5.458,3.198 5.615,3.396 0.156,0.198 10 false 1

for RHD



C366179E12
1.677,0.531 1.833,0.729 0.156,0.198 10 false 5 1.677,1.073 1.917,1.271 0.24,0.198 10 false 16 0.26,1.573 0.75,1.771 0.49,0.198 10 false F115 0.26,1.729 2.344,1.896 2.083,0.167 10 false No. 4 CAN Junction Connector 5.438,0.51 5.594,0.708 0.156,0.198 10 false 3 5.448,1.063 5.604,1.26 0.156,0.198 10 false 2 5.677,0.646 6.25,0.813 0.573,0.167 10 false CANH 5.667,1.177 6.24,1.344 0.573,0.167 10 false CANL 5.677,2.26 6.25,2.427 0.573,0.167 10 false IG1 5.677,2.781 6.25,2.948 0.573,0.167 10 false BAT 5.677,3.302 6.25,3.469 0.573,0.167 10 false ESS 5.604,3.698 6.177,3.865 0.573,0.167 10 false F69 5.615,3.875 6.688,4.125 1.073,0.25 10 false Steering Sensor 4.146,2.927 5.396,3.177 1.25,0.25 10 false ECU-DCC NO. 1 4.188,2.375 5.438,2.625 1.25,0.25 10 false ECU-IG1 NO. 2 2.052,2.208 3.552,2.458 1.5,0.25 10 false from IG1-NO. 1 Relay 2.042,2.74 3.542,2.99 1.5,0.25 10 false from Auxiliary Battery 5.458,2.115 5.615,2.313 0.156,0.198 10 false 4 5.458,2.656 5.615,2.854 0.156,0.198 10 false 5 5.458,3.198 5.615,3.396 0.156,0.198 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch), turn the cruise control main switch on, turn the LDA main switch on and then drive the vehicle at a speed of 5 km/h (3 mph) or more for approximately 61 seconds or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (STEERING SENSOR BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the steering sensor connector.


c.
C366208C01
1.417,0.333 1.917,0.583 0.5,0.25 1.25,1.667 1.51,1.323 true 2,1.667 1.76,1.323 true 0.188,0.167 0.5,0.365 0.313,0.198 10 false *a 1.531,0.365 1.927,0.563 0.396,0.198 10 false F69 0.927,1.708 1.406,1.875 0.479,0.167 10 false CANL 1.979,1.698 2.458,1.865 0.479,0.167 10 false CANH
*a Front view of wire harness connector
(to Steering Sensor)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F69-3 (CANH) - F69-2 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (STEERING SENSOR)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C366208C03
1.417,0.333 1.917,0.583 0.5,0.25 1.073,1.667 1.333,1.323 true 2.156,1.688 1.917,1.344 true 2.573,1.688 2.104,1.333 true 0.188,0.167 0.5,0.365 0.313,0.198 10 false *a 1.531,0.365 1.927,0.563 0.396,0.198 10 false F69 0.823,1.698 1.302,1.865 0.479,0.167 10 false ESS 2.563,1.729 3.042,1.896 0.479,0.167 10 false BAT 2.156,1.729 2.635,1.896 0.479,0.167 10 false IG1
*a Front view of wire harness connector
(to Steering Sensor)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F69-1 (ESS) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) auxiliary battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F69-5 (BAT) - Body ground Power switch off 11 to 14 V
F69-4 (IG1) - Body ground Power switch on (IG) 11 to 14 V



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)