Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2016.10–2020.08
RM32K0E _57 Power Source / Network _059857 NETWORKING _0293867 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Main Body ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Main Body ECU Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "Main Body" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "Main Body" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Main Body" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Main Body ECU Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Main body ECU (multiplex network body ECU) branch line or connector

·

Power source circuit of main body ECU (multiplex network body ECU) or instrument panel junction block assembly

·

Main body ECU (multiplex network body ECU) or instrument panel junction block assembly ground circuit

·

Main body ECU (multiplex network body ECU) or instrument panel junction block assembly



WIRING DIAGRAM

C369871E02
0.198,1.667 2.323,1.969 2.125,0.302 10 false No. 3 CAN Junction Connector 0.208,1.51 0.76,1.698 0.552,0.188 10 false F114 1.74,0.49 2.292,0.677 0.552,0.188 10 false 2 1.74,1.031 2.292,1.219 0.552,0.188 10 false 13 5.583,0.417 6.135,0.604 0.552,0.188 10 false 14 5.583,0.948 7.156,1.125 1.573,0.177 10 false 13 5.563,0.594 6.115,0.781 0.552,0.188 10 false F15 5.563,1.135 6.115,1.323 0.552,0.188 10 false F15 5.906,0.594 7.156,0.792 1.25,0.198 10 false CANH 5.906,1.135 7.156,1.333 1.25,0.198 10 false CANL 5.906,2.604 7.156,2.802 1.25,0.198 10 false BECU 5.906,3.094 7.156,3.292 1.25,0.198 10 false ACC 5.906,4.823 7.156,5.021 1.25,0.198 10 false IG 5.906,7.49 7.156,7.688 1.25,0.198 10 false GND1 5.563,2.615 5.917,2.802 0.354,0.188 10 false MB 5.563,3.135 5.969,3.302 0.406,0.167 10 false MB 5.563,4.802 6.073,4.969 0.51,0.167 10 false MB 5.563,7.469 6,7.656 0.438,0.188 10 false MB 3.927,2.75 5.177,2.948 1.25,0.198 10 false ECU-DCC NO. 2 4.75,3.271 6,3.469 1.25,0.198 10 false ECU-ACC 4.646,5.927 5.896,6.125 1.25,0.198 10 false ECU-IG1 NO. 4 3.729,6.604 4.979,6.802 1.25,0.198 10 false IG1-NO. 1 3.875,3.948 5.125,4.146 1.25,0.198 10 false ACC 5.583,2.427 5.969,2.604 0.385,0.177 10 false 31 5.583,2.938 6.031,3.135 0.448,0.198 10 false 30 5.583,4.615 5.958,4.802 0.375,0.188 10 false 32 5.583,7.281 5.958,7.458 0.375,0.177 10 false 11 5.448,8 7.156,8.458 1.708,0.458 10 false Main Body ECU (Multiplex Network Body ECU) 3.01,8 4.667,8.479 1.656,0.479 10 false Instrument Panel Junction Block Assembly 3.083,7.469 3.521,7.656 0.438,0.188 10 false 3D 3.083,6.323 3.521,6.51 0.438,0.188 10 false 3A 3.083,5.333 3.521,5.521 0.438,0.188 10 false 3D 3.083,4.802 3.521,4.99 0.438,0.188 10 false 3A 3.083,3.656 3.521,3.844 0.438,0.188 10 false 3A 3.083,3.125 3.521,3.313 0.438,0.188 10 false 3K 3.083,2.615 3.521,2.802 0.438,0.188 10 false 3F 3.083,6.135 3.521,6.323 0.438,0.188 10 false 17 3.094,3.469 3.531,3.656 0.438,0.188 10 false 30 3.125,2.938 3.563,3.125 0.438,0.188 10 false 1 3.125,2.427 3.563,2.615 0.438,0.188 10 false 1 3.125,7.281 3.563,7.469 0.438,0.188 10 false 3 3.094,5.146 3.531,5.333 0.438,0.188 10 false 30 3.094,4.615 3.531,4.802 0.438,0.188 10 false 15 0.542,2.604 2.667,2.906 2.125,0.302 10 false from Auxiliary Battery 0.552,3.125 2.677,3.427 2.125,0.302 10 false from Auxiliary Battery 0.073,3.656 1.969,4.063 1.896,0.406 10 false from Certification ECU (Smart Key ECU Assembly) 0.073,6.313 1.938,6.802 1.865,0.49 10 false from Certification ECU (Smart Key ECU Assembly) 2.323,2.76 3.219,3.01 0.896,0.25 10 false D/C CUT

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the power switch on (IG), turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch), turn the LDA main switch on and wait for approximately 20 seconds or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the main body ECU (multiplex network body ECU) connector.


c.
C349831C07
1.406,0.177 1.76,0.427 0.354,0.25 2.01,1.781 2.271,1.021 true 1.885,1.781 2.219,0.656 true 0.125,0.094 0.438,0.292 0.313,0.198 10 false *a 1.479,0.24 1.865,0.448 0.385,0.208 10 false F15 2.323,0.906 2.792,1.156 0.469,0.25 10 false CANH 2.271,0.552 2.74,0.802 0.469,0.25 10 false CANL
*a Front view of wire harness connector
(to Main Body ECU (Multiplex Network Body ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F15-14 (CANH) - F15-13 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

b.
C227508C37
1.531,0.552 1.917,0.792 0.385,0.24 1.198,1.073 0.969,0.76 true 2.906,1.083 2.573,0.802 true 2.979,1.073 2.594,0.438 true 2.854,1.531 3.094,1.135 true 0.052,0.052 0.365,0.208 0.313,0.156 10 false *a 1.615,0.583 1.927,0.74 0.313,0.156 10 false MB 2.188,0.344 2.625,0.521 0.438,0.177 10 false BECU 2.25,0.719 2.688,0.896 0.438,0.177 10 false ACC 2.677,1.531 3.115,1.708 0.438,0.177 10 false IG 0.563,0.667 1,0.844 0.438,0.177 10 false GND1
*a Front view of wire harness connector
(to Main Body ECU (Multiplex Network Body ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
MB-11 (GND1) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω


NOTICE:

Perform this inspection with the wire harness connected to the instrument panel junction block assembly.



c.

Reconnect the cable to the negative (-) auxiliary battery terminal.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
MB-31 (BECU) - Body ground Power switch off 11 to 14 V
MB-30 (ACC) - Body ground Power switch on (ACC) 11 to 14 V
MB-32 (IG) - Body ground Power switch on (IG) 11 to 14 V


NOTICE:

Perform this inspection with the wire harness connected to the instrument panel junction block assembly.



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG (BECU) C
NG (ACC) D
NG (IG) E
NG (GND1) F



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

3.CHECK HARNESS AND CONNECTOR (BECU SIGNAL CIRCUIT)

D

GO TO LIGHTING (INT) SYSTEM (ACC SIGNAL CIRCUIT)

E

GO TO LIGHTING (INT) SYSTEM (IG SIGNAL CIRCUIT)

F

4.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)
3.CHECK HARNESS AND CONNECTOR (BECU SIGNAL CIRCUIT)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the instrument panel junction block assembly connector.


c.

Reconnect the cable to the negative (-) auxiliary battery terminal.


d.
C352870C02
1.458,0.135 1.781,0.365 0.323,0.229 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 1.552,0.167 1.865,0.365 0.313,0.198 10 false 3F
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
3F-1 - Body ground Power switch off 11 to 14 V



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

B

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR (BECU SIGNAL CIRCUIT)

4.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the instrument panel junction block assembly connector.


c.
C352871C02
1.177,0.146 1.51,0.385 0.333,0.24 0.083,0.052 0.396,0.25 0.313,0.198 10 false *a 1.271,0.188 1.583,0.385 0.313,0.198 10 false 3D
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3D-3 - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

B

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR (GROUND CIRCUIT)