Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2016.10–2019.09
RM32K0E _57 Power Source / Network _059857 NETWORKING _0293867 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Motor Generator Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Motor Generator Control ECU Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "Motor Generator" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "Motor Generator" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Motor Generator" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Motor Generator Control ECU Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Inverter with converter assembly branch line or connector

·

Power source circuit of inverter with converter assembly

·

Inverter with converter assembly ground circuit

·

Inverter with converter assembly



WIRING DIAGRAM

for LHD


C366190E11
0.125,1.49 0.552,1.698 0.427,0.208 10 false F124 0.094,1.656 2.135,1.875 2.042,0.219 10 false No. 5 CAN Junction Connector 1.625,0.5 1.844,0.698 0.219,0.198 10 false 10 1.625,1.042 1.844,1.24 0.219,0.198 10 false 21 2.073,3.26 3.135,3.5 1.063,0.24 10 false from IGCT Relay 4.229,3.427 5.021,3.656 0.792,0.229 10 false IGCT NO. 2 5.781,0.594 6.573,0.823 0.792,0.229 10 false CANH 5.781,1.135 6.573,1.365 0.792,0.229 10 false CANL 5.781,2.198 6.573,2.427 0.792,0.229 10 false +B2 5.802,2.729 6.594,2.958 0.792,0.229 10 false +B 5.802,3.271 6.594,3.5 0.792,0.229 10 false IGCT 5.792,3.813 6.583,4.042 0.792,0.229 10 false GND2 5.792,4.344 6.583,4.573 0.792,0.229 10 false GND1 5.594,0.5 5.813,0.698 0.219,0.198 10 false 1 5.594,1.031 5.813,1.229 0.219,0.198 10 false 7 5.594,2.115 5.813,2.313 0.219,0.198 10 false 5 5.594,2.646 5.813,2.844 0.219,0.198 10 false 6 5.521,3.177 5.74,3.375 0.219,0.198 10 false 12 5.531,3.719 5.75,3.917 0.219,0.198 10 false 23 5.531,4.26 5.75,4.458 0.219,0.198 10 false 24 5.5,4.719 5.813,4.927 0.313,0.208 10 false C65 5.5,4.885 6.875,5.302 1.375,0.417 10 false Inverter with Converter Assembly 4.333,2.406 5.125,2.635 0.792,0.229 10 false PCU FR


for RHD


C366190E12
0.104,1.531 0.531,1.74 0.427,0.208 10 false F113 0.094,1.708 2.135,1.927 2.042,0.219 10 false No. 2 CAN Junction Connector 1.625,0.5 1.844,0.698 0.219,0.198 10 false 3 1.625,1.042 1.844,1.24 0.219,0.198 10 false 14 2.073,3.26 3.135,3.5 1.063,0.24 10 false from IGCT Relay 4.229,3.427 5.021,3.656 0.792,0.229 10 false IGCT NO. 2 5.781,0.594 6.573,0.823 0.792,0.229 10 false CANH 5.781,1.135 6.573,1.365 0.792,0.229 10 false CANL 5.781,2.198 6.573,2.427 0.792,0.229 10 false +B2 5.802,2.729 6.594,2.958 0.792,0.229 10 false +B 5.802,3.271 6.594,3.5 0.792,0.229 10 false IGCT 5.792,3.813 6.583,4.042 0.792,0.229 10 false GND2 5.792,4.344 6.583,4.573 0.792,0.229 10 false GND1 5.594,0.5 5.813,0.698 0.219,0.198 10 false 1 5.594,1.031 5.813,1.229 0.219,0.198 10 false 7 5.594,2.115 5.813,2.313 0.219,0.198 10 false 5 5.594,2.646 5.813,2.844 0.219,0.198 10 false 6 5.521,3.177 5.74,3.375 0.219,0.198 10 false 12 5.531,3.719 5.75,3.917 0.219,0.198 10 false 23 5.531,4.26 5.75,4.458 0.219,0.198 10 false 24 5.5,4.719 5.813,4.927 0.313,0.208 10 false C65 5.5,4.885 6.875,5.302 1.375,0.417 10 false Inverter with Converter Assembly 4.365,2.406 5.156,2.635 0.792,0.229 10 false PCU FR


CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A371653

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A371654C04
1.563,1.229 1.333,0.813 true 1.156,0.677 1.469,0.875 0.313,0.198 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.


NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION




NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the power switch on (IG) and wait at least approximately 8 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (INVERTER WITH CONVERTER ASSEMBLY BRANCH LINE)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Disconnect the inverter with converter assembly connector.


d.
C349824C05
1.479,0.25 1.896,0.51 0.417,0.26 0.615,1.604 1.292,1.833 true 0.688,1.219 1.333,1.698 true 0.073,0.052 0.385,0.25 0.313,0.198 10 false *a 0.24,1.125 0.677,1.323 0.438,0.198 10 false CANH 0.167,1.51 0.604,1.708 0.438,0.198 10 false CANL 1.563,0.281 2,0.479 0.438,0.198 10 false C65
*a Front view of wire harness connector
(to Inverter with Converter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C65-1 (CANH) - C65-7 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C349824C06
1.479,0.25 1.896,0.51 0.417,0.26 1.969,1.833 2.854,1.833 true 1.958,1.688 2.354,0.948 true 1.813,1.688 1.531,0.885 true 1.948,2.073 2.396,2.75 true 1.823,2.063 2.104,2.875 true 0.073,0.052 0.385,0.25 0.313,0.198 10 false *a 1.219,0.781 1.656,0.979 0.438,0.198 10 false +B2 2.927,1.771 3.365,1.969 0.438,0.198 10 false IGCT 1.563,0.281 2,0.479 0.438,0.198 10 false C65 2.427,0.854 2.865,1.052 0.438,0.198 10 false +B 2.479,2.688 2.917,2.885 0.438,0.198 10 false GND1 1.979,2.938 2.417,3.135 0.438,0.198 10 false GND2
*a Front view of wire harness connector
(to Inverter with Converter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C65-23 (GND2) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
C65-24 (GND1) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) auxiliary battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C65-5 (+B2) - Body ground Power switch on (IG) 11 to 14 V
C65-6 (+B) - Body ground Power switch on (IG) 11 to 14 V
C65-12 (IGCT) - Body ground Power switch on (IG) 11 to 14 V



Result:
Result
OK
NG



OK

REPLACE MG ECU (REPLACE INVERTER WITH CONVERTER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)