Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2016.10–2019.09
RM32K0E _57 Power Source / Network _059857 NETWORKING _0293867 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Grille Shutter Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Grille Shutter Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "Grill Shutter" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "Grill Shutter" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Grill Shutter" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Grille Shutter Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Swing grille actuator assembly branch line or connector

·

Power source circuit of swing grille actuator assembly

·

Swing grille actuator assembly ground circuit

·

Swing grille actuator assembly



WIRING DIAGRAM

C366191E03
0.094,1.573 0.5,1.781 0.406,0.208 10 false F111 0.083,1.719 2.052,1.927 1.969,0.208 10 false No. 1 CAN Junction Connector 1.635,0.521 2.042,0.729 0.406,0.208 10 false 2 1.615,1.063 2.021,1.271 0.406,0.208 10 false 12 2.177,2.198 3.542,2.448 1.365,0.25 10 false from Auxiliary Battery 4.375,2.365 5.271,2.594 0.896,0.229 10 false ECU-B NO. 2 5.604,0.542 5.813,0.729 0.208,0.188 10 false 6 5.604,1.073 5.813,1.26 0.208,0.188 10 false 5 5.604,2.115 5.813,2.302 0.208,0.188 10 false 1 5.604,2.656 5.813,2.844 0.208,0.188 10 false 3 5.5,3.135 5.906,3.344 0.406,0.208 10 false A32 5.49,3.292 6.833,3.729 1.344,0.438 10 false Swing Grille Actuator Assembly 5.781,0.615 6.302,0.813 0.521,0.198 10 false CANP 5.781,1.146 6.302,1.344 0.521,0.198 10 false CANN 5.781,2.208 6.302,2.406 0.521,0.198 10 false +B 5.781,2.76 6.302,2.958 0.521,0.198 10 false GND

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the power switch on (IG) and wait at least approximately 9 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (SWING GRILLE ACTUATOR ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the swing grille actuator assembly connector.


c.
C349838C12
1.49,0.198 1.99,0.448 0.5,0.25 1.583,1.833 1.927,1.219 true 2.375,1.823 2.125,1.219 true 0.094,0.083 0.406,0.24 0.313,0.156 10 false *a 1.615,0.219 2.073,0.417 0.458,0.198 10 false A32 1.125,1.781 1.583,1.979 0.458,0.198 10 false CANN 2.458,1.771 2.906,1.969 0.448,0.198 10 false CANP
*a Front view of wire harness connector
(to Swing Grille Actuator Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A32-6 (CANP) - A32-5 (CANN) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (SWING GRILLE ACTUATOR ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C349838C13
1.49,0.198 1.99,0.448 0.5,0.25 0.917,1.823 1.26,1.208 true 1.896,1.823 1.646,1.219 true 0.094,0.083 0.406,0.24 0.313,0.156 10 false *a 1.615,0.219 2.073,0.417 0.458,0.198 10 false A32 0.667,1.771 1.125,1.969 0.458,0.198 10 false +B 1.969,1.792 2.417,1.99 0.448,0.198 10 false GND
*a Front view of wire harness connector
(to Swing Grille Actuator Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A32-3 (GND) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) auxiliary battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A32-1 (+B) - Body ground Power switch off 11 to 14 V



Result:
Result
OK
NG



OK

REPLACE SWING GRILLE ACTUATOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)