Home › Engine / Hybrid System › 2ZR-FXE (INTAKE / EXHAUST) › EXHAUST PIPE
RM32K0E _51 Engine / Hybrid System _059910 2ZR-FXE INTAKE / EXHAUST _0293912 EXHAUST PIPE A

2ZR-FXE INTAKE / EXHAUST  EXHAUST PIPE  INSTALLATION  


PROCEDURE

Hide 17410 2.INSTALL FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)

a.
A128853

Using a vernier caliper, measure the free length of the compression springs.

Standard Length 43.0 mm (1.69 in.)
Minimum Free Length 41.5 mm (1.63 in.)

If the free length is less than the minimum, replace the compression spring.


b.

Temporarily install a new exhaust pipe gasket to the exhaust manifold (TWC: Front Catalyst).


c.
A181728C68
2.813,1.563 2.688,1.563 2.688,1.563 2.385,1.875 false 1.615,3.188 1.99,3.188 1.99,3.188 1.99,2.365 false 1.458,0.667 1.813,0.667 1.813,0.667 1.813,1.125 false 1.292,0.573 1.583,0.792 0.292,0.219 10 false *1 2.854,1.49 3.135,1.698 0.281,0.208 10 false *a 1.448,3.104 1.771,3.344 0.323,0.24 10 false *2
*1 Exhaust Manifold (TWC: Front Catalyst)
*2 Exhaust Pipe Gasket
*a Wooden Block


Using a plastic hammer and wooden block, tap in the exhaust pipe gasket until its surface is flush with the exhaust manifold (TWC: Front Catalyst).

NOTICE:
·

Be careful with the installation direction of the exhaust pipe gasket.

·

Do not reuse the exhaust pipe gasket.

·

Do not damage the exhaust pipe gasket.

·

Do not push in the exhaust pipe gasket by using the exhaust pipes when connecting them.




d.

Connect the front exhaust pipe assembly (TWC: Rear Catalyst) to the 2 exhaust pipe supports.


e.

Install the front exhaust pipe assembly (TWC: Rear Catalyst) to the exhaust manifold (TWC: Front Catalyst) with the 2 compression springs and 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
A258941C18
2.406,0.771 2.51,0.167 2.51,0.167 2.677,0.167 false 0.771,0.229 0.906,0.229 0.906,0.229 1.156,0.594 false 0.771,1.198 0.927,1.198 0.927,1.198 1.094,0.896 false 0.406,1.417 0.615,1.573 0.208,0.156 10 *a 0.573,0.146 0.823,0.302 0.25,0.156 10 *1 0.573,1.125 0.813,1.313 0.24,0.188 10 *2 2.698,0.083 2.927,0.26 0.229,0.177 10 *3
*1 Exhaust Manifold (TWC: Front Catalyst)
*2 Front Exhaust Pipe Assembly (TWC: Rear Catalyst)
*3 Exhaust Pipe Gasket
*a Space between Flanges: 8.5 mm (0.335 in.)


After installation, check that the space between the flanges of the exhaust manifold (TWC: Front Catalyst) and front exhaust pipe assembly (TWC: Rear Catalyst) is consistent front-to-rear and left-to-right.



f.

Engage the wire harness clamp.


g.

Connect the heated oxygen sensor connector.


Hide 17430 3.INSTALL TAIL EXHAUST PIPE ASSEMBLY

a.
A128853

Using a vernier caliper, measure the free length of the compression springs.

Standard Length 40 mm (1.57 in.)
Minimum Free Length 38.5 mm (1.52 in.)

If the free length is less than the minimum, replace the compression spring.


b.

Temporarily install a new exhaust pipe gasket to the front exhaust pipe assembly (TWC: Rear Catalyst).


c.
A181728C68
2.813,1.563 2.688,1.563 2.688,1.563 2.385,1.875 false 1.615,3.188 1.99,3.188 1.99,3.188 1.99,2.365 false 1.458,0.667 1.813,0.667 1.813,0.667 1.813,1.125 false 1.292,0.573 1.583,0.792 0.292,0.219 10 false *1 2.854,1.49 3.135,1.698 0.281,0.208 10 false *a 1.448,3.104 1.771,3.344 0.323,0.24 10 false *2
*1 Front Exhaust Pipe Assembly (TWC: Rear Catalyst)
*2 Exhaust Pipe Gasket
*a Wooden Block


Using a plastic hammer and wooden block, tap in the exhaust pipe gasket until its surface is flush with the front exhaust pipe assembly (TWC: Rear Catalyst).

NOTICE:
·

Be careful with the installation direction of the exhaust pipe gasket.

·

Do not reuse the exhaust pipe gasket.

·

Do not damage the exhaust pipe gasket.

·

Do not push in the exhaust pipe gasket by using the exhaust pipes when connecting them.




d.

Connect the tail exhaust pipe assembly to the 4 exhaust pipe supports.


e.

Install the tail exhaust pipe assembly to the front exhaust pipe assembly (TWC: Rear Catalyst) with the 2 bolts and 2 compression springs.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
A258941C18
2.406,0.771 2.51,0.167 2.51,0.167 2.677,0.167 false 0.771,0.229 0.906,0.229 0.906,0.229 1.156,0.594 false 0.771,1.198 0.927,1.198 0.927,1.198 1.094,0.896 false 0.406,1.417 0.615,1.573 0.208,0.156 10 *a 0.573,0.146 0.823,0.302 0.25,0.156 10 *1 0.573,1.125 0.813,1.313 0.24,0.188 10 *2 2.698,0.083 2.927,0.26 0.229,0.177 10 *3
*1 Front Exhaust Pipe Assembly (TWC: Rear Catalyst)
*2 Tail Exhaust Pipe Assembly
*3 Exhaust Pipe Gasket
*a Space between Flanges: 6.5 mm (0.256 in.)


After installation, check that the space between the flanges of the tail exhaust pipe assembly and front exhaust pipe assembly (TWC: Rear Catalyst) is consistent front-to-rear and left-to-right.



Hide 57533B 4.INSTALL FRONT FLOOR CENTER BRACE

Hide 58165B 6.INSTALL FRONT FLOOR COVER RH

HINT:

Perform the same procedure as for the front floor cover LH.


Hide 7.INSPECT FOR EXHAUST GAS LEAK

If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.

HINT:

Perform Inspection After Repair after repairing an exhaust gas leak.

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION