Home › Engine / Hybrid System › 2ZR-FXE (EMISSION CONTROL) › CANISTER › 2016.10–2018.05
RM32K0E _51 Engine / Hybrid System _060064 2ZR-FXE EMISSION CONTROL _0294229 CANISTER A

2ZR-FXE EMISSION CONTROL  CANISTER  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during canister (charcoal canister assembly) removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Gas leak from exhaust system is repaired Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

PROCEDURE

Hide 17430 1.REMOVE TAIL EXHAUST PIPE ASSEMBLY

Hide 57628C 2.REMOVE REAR FLOOR SIDE MEMBER COVER LH

Hide 57627A 3.REMOVE REAR FLOOR SIDE MEMBER COVER RH

Hide 48832A 4.REMOVE REAR NO. 1 STABILIZER BAR BRACKET

a.
A393935

Remove the 4 bolts and 2 rear No. 1 stabilizer bar brackets from the vehicle body.


Hide 77740 5.REMOVE CANISTER (CHARCOAL CANISTER ASSEMBLY)

a.
A393936C01
2.229,3.094 2.229,2.885 false 1.958,2.323 1.667,2.167 false 2.51,2.281 2.24,2.01 true 2.563,1.688 1.99,1.198 true 2.615,1.604 2.854,1.76 0.24,0.156 10 true *1 1.479,2.052 1.792,2.208 0.313,0.156 10 false *2 2.156,3.063 2.469,3.219 0.313,0.156 10 false *a 2.073,1.885 2.385,2.042 0.313,0.156 10 false *b
*1 Fuel Tank Vent Hose Sub-assembly
*2 Pipe (canister (charcoal canister assembly))
*a Tube Connector
*b O-ring
V100135

Pinch
V100136

Pull off


Disconnect the fuel tank vent hose sub-assembly from the canister (charcoal canister assembly).

NOTICE:
·

Remove any dirt or foreign matter on the tube connector before performing this work.

·

Do not allow any scratches or foreign matter to get on the parts when disconnecting them as the tube connector has an O-ring that seals the pipe.

·

Perform this work by hand. Do not use any tools.

·

Do not forcibly bend, twist or turn the air line tube.

·

Protect the disconnected parts by covering them with plastic bags after disconnecting the air line tube.

·

If the tube connector and pipe are stuck, push and pull to release them.



i.

Push the fuel tank vent hose sub-assembly firmly toward the canister (charcoal canister assembly).


ii.

Pinch the tube connector as shown in the illustration.


iii.

Pull off the fuel tank vent hose sub-assembly from the pipe (canister (charcoal canister assembly)).



b.

Disconnect the fuel tank vent hose from the canister (charcoal canister assembly).

A393937C01
5.24,1.042 5,0.583 5,0.583 4.833,0.583 false 5.5,1.688 5.25,2.417 5.25,2.417 5.083,2.417 true 6.188,1.094 6.333,0.583 6.333,0.583 6.5,0.583 false 5.938,1.823 6.167,2.417 6.167,2.417 6.333,2.417 false 2.229,2.25 2.563,2.25 false 1.417,2.333 1.583,2.333 1.583,2.333 1.844,1.927 true 2.552,1.146 2.917,1.417 2.917,1.417 3.083,1.417 true 3.156,1.313 3.417,1.5 0.26,0.188 10 true *1 6.583,0.479 6.896,0.635 0.313,0.156 10 false *2 6.417,2.323 6.792,2.5 0.375,0.177 10 false *a 1.229,2.24 1.542,2.396 0.313,0.156 10 false *b 4.646,0.479 4.958,0.635 0.313,0.156 10 false *c 4.865,2.313 5.177,2.469 0.313,0.156 10 false *d 2.646,2.146 3.021,2.323 0.375,0.177 10 false *a
*1 Fuel Tank Vent Hose *2 Pipe (Canister (Charcoal Canister Assembly))
*a Retainer *b Tab
*c Tube Connector *d O-ring
V100135

Pinch
V100136

Pull off


NOTICE:
·

Remove any dirt or foreign matter on the tube connector before performing this work.

·

Do not allow any scratches or foreign matter to get on the parts when disconnecting them as the tube connector has an O-ring that seals the pipe (canister (charcoal canister assembly)).

·

Perform this work by hand. Do not use any tools.

·

Do not forcibly bend, twist or turn the fuel tank vent hose.

·

Protect the disconnected parts by covering them with plastic bags after disconnecting the fuel tank vent hose.

·

If the tube connector and pipe (canister (charcoal canister assembly)) are stuck, push and pull to release them.



HINT:

Do not remove the retainer.


i.

Pinch the tabs of the retainer to disengage the lock claws and pull it down.


ii.

Pull off the fuel tank vent hose.



c.
A393938

Slide the clip and disconnect the charcoal canister hose from the canister (charcoal canister assembly).


d.
A393939

Remove the bolt.


e.
A393940

Remove the canister (charcoal canister assembly) from vehicle body as shown in the illustration.