The airbag sensor assembly has a built-in yaw rate and acceleration sensor and detects the vehicle condition using 2 circuits (GL1, GL2).
The skid control ECU (brake booster with master cylinder assembly) receives signals from the hybrid vehicle control ECU, steering angle sensor, certification ECU (smart key ECU assembly), inverter with converter assembly and yaw rate and acceleration sensor (airbag sensor assembly) via CAN communication.
| DTC No. | Detection Item | INF Code | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|---|
| U0073 | Control Module Communication Bus Off | 461
462 463 |
·
INF Code: 461 -
Either of the following is detected: (1)
Yaw rate and acceleration sensor communication is disabled for 1 second or more. (2)
Yaw rate and acceleration sensor communication is disabled once or more per 5 seconds 10 times or more within 60 seconds. ·
INF Code: 462 -
Either of the following is detected: (1)
Steering angle sensor communication is disabled for 1 second or more. (2)
Steering angle sensor communication is disabled once or more per 5 seconds 10 times or more within 60 seconds. ·
INF Code: 463 -
Bus off occurs once or more per 0.1 seconds 10 times repeatedly. |
·
INF Code: 461 -
CAN communication line -
Yaw rate and acceleration sensor (airbag sensor assembly) -
Skid control ECU (brake booster with master cylinder assembly) ·
INF Code: 462 -
CAN communication line -
Steering angle sensor -
Skid control ECU (brake booster with master cylinder assembly) ·
INF Code: 463 -
CAN communication line -
Skid control ECU (brake booster with master cylinder assembly) |
Electronically controlled brake system DTC |
| U0110 | Lost Communication with Drive Motor Control Module "A" | 1153
1154 |
·
INF Code: 1153 -
When terminal IG2 voltage is 9.5 V or more, data from the inverter with converter assembly cannot be received for 2 seconds or more. ·
INF Code: 1154 -
When terminal IG2 voltage is 9.5 V or more, the condition in which data from the inverter with converter assembly cannot be received once or more within 5 seconds occurs 10 times in succession. |
·
CAN communication line ·
Inverter with converter assembly ·
Skid control ECU (brake booster with master cylinder assembly) |
Electronically controlled brake system DTC |
| U0120 | Lost Communication With Starter / Generator Control Module | 1158 | Push start switch data is invalid for 3 seconds or more. | ·
CAN communication line ·
Certification ECU (smart key ECU assembly) ·
Skid control ECU (brake booster with master cylinder assembly) |
Electronically controlled brake system DTC |
| U0124 | Lost Communication With Lateral Acceleration Sensor Module | 591
592 |
·
INF Code: 591 -
Acceleration sensor communication is disabled for 1 second or more. ·
INF Code: 592 -
Acceleration sensor communication is disabled once or more per 5 seconds 10 times or more within 60 seconds. |
·
CAN communication line ·
Acceleration sensor (airbag sensor assembly) ·
Skid control ECU (brake booster with master cylinder assembly) |
ABS DTC |
| U0126 | Lost Communication With Steering Angle Sensor Module | 741
742 |
·
INF Code: 741 -
Steering angle sensor communication is disabled for 1 second or more. ·
INF Code: 742 -
Steering angle sensor communication is disabled once or more per 5 seconds 10 times or more within 60 seconds. |
·
CAN communication line ·
Steering angle sensor ·
Skid control ECU (brake booster with master cylinder assembly) |
VSC DTC |
| U0128 | Lost Communication With EPB Module | 425 | With terminal IG1 voltage at 10 V or more, data cannot be received from the electric parking brake ECU for 1 second or more. | ·
CAN communication line ·
Electric parking brake ECU ·
Skid control ECU (brake booster with master cylinder assembly) |
Brake hold DTC |
| U0293 | Lost Communication with Hybrid Vehicle Control System | 411
412 413 |
·
INF Code: 411, 413 -
When terminal IG2 voltage is 9.5 V or more, data from the hybrid vehicle control ECU cannot be received for 2 seconds or more. ·
INF Code: 412 -
When terminal IG2 voltage is 9.5 V or more, the condition in which data from the hybrid vehicle control ECU cannot be received once or more within 5 seconds occurs 10 times in succession. |
·
CAN communication line ·
Hybrid vehicle control ECU ·
Skid control ECU (brake booster with master cylinder assembly) |
Electronically controlled brake system DTC |
| Vehicle Condition | |||
|---|---|---|---|
| Pattern 1 | Pattern 2 | ||
| Diagnosis Condition | - | - | - |
| Malfunction Status | Yaw rate and acceleration sensor communication is disabled. | ○ | - |
| Communication with the yaw rate and acceleration sensor is invalid once or more within 5 seconds. | - | ○ | |
| Detection Time | 1 second or more | Occurs 10 times or more within 60 seconds | |
| Number of Trips | 1 trip | 1 trip | |
DTC will be output when conditions for either of the patterns in the table above are met.
| Vehicle Condition | |||
|---|---|---|---|
| Pattern 1 | Pattern 2 | ||
| Diagnosis Condition | - | - | - |
| Malfunction Status | Steering angle sensor communication is disabled. | ○ | - |
| Communication with the steering angle sensor is invalid once or more within 5 seconds. | - | ○ | |
| Detection Time | 1 second or more | Occurs 10 times or more within 60 seconds | |
| Number of Trips | 1 trip | 1 trip | |
DTC will be output when conditions for either of the patterns in the table above are met.
Clear the DTCs.
Turn the power switch off.
Turn the power switch on (IG).
Check if the same DTC is output.
If CAN communication system DTCs and relevant sensor DTCs are output simultaneously, troubleshoot the relevant sensor DTCs (for the ABS, VSC and/or electronically controlled brake system) after the CAN communication system returns to normal.
| Result | Proceed to |
|---|---|
| CAN communication system DTCs are output. | A |
| DTCs are not output. | B |
A
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
B
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING