Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM32K0E _54 Brake _060044 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0294924 ELECTRONICALLY CONTROLLED BRAKE SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  ABS Warning Light Remains ON  


DESCRIPTION

The skid control ECU (brake booster with master cylinder assembly) is connected to the combination meter assembly via CAN communication.

If any of the following is detected, the ABS warning light remains on:

·

The skid control ECU (brake booster with master cylinder assembly) connector is disconnected from the brake booster with master cylinder assembly.

·

There is a malfunction in the skid control ECU (brake booster with master cylinder assembly) internal circuit.

·

There is an open in the wire harness between the combination meter assembly and the skid control ECU (brake booster with master cylinder assembly).

·

The ABS control system is defective.


HINT:

In some cases, the GTS cannot be used when the skid control ECU (brake booster with master cylinder assembly) is malfunctioning.


WIRING DIAGRAM

C349890E07
5.708,0.729 6.021,0.927 0.313,0.198 10 false 42 5.948,0.906 6.385,1.125 0.438,0.219 10 false CA1L 5.708,1.302 6.021,1.5 0.313,0.198 10 false 43 5.948,1.469 6.385,1.719 0.438,0.25 10 false CA1H 5.708,2.063 6.021,2.26 0.313,0.198 10 false 23 5.958,2.156 6.313,2.354 0.354,0.198 10 false IG1 5.708,2.792 6.021,2.99 0.313,0.198 10 false 26 5.948,2.875 6.469,3.104 0.521,0.229 10 false GND1 5.708,3.208 6.021,3.406 0.313,0.198 10 false 39 5.948,3.302 6.385,3.552 0.438,0.25 10 false GND2 5.073,3.948 5.385,4.146 0.313,0.198 10 false A39 5.063,4.125 7.115,4.563 2.052,0.438 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 4.573,2.333 5.521,2.604 0.948,0.271 10 false ECU-IG1 NO. 2 2.5,2.156 4.031,2.396 1.531,0.24 10 false from IG1-NO. 1 Relay 2.104,3.177 3.969,3.406 1.865,0.229 10 false : CAN Communication Line 1.396,0.719 1.708,0.917 0.313,0.198 10 false 31 0.906,0.927 1.313,1.156 0.406,0.229 10 false CANL 1.396,1.302 1.708,1.5 0.313,0.198 10 false 32 0.896,1.49 1.375,1.729 0.479,0.24 10 false CANH 0.135,3.938 0.448,4.135 0.313,0.198 10 false F4 0.125,4.104 1.948,4.5 1.823,0.396 10 false Combination Meter Assembly (Meter Circuit Plate)

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before performing this procedure, depress the brake pedal and confirm that the stop lights illuminate.



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

2.CHECK IF BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY CONNECTOR IS SECURELY CONNECTED

B

2.CHECK IF BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU (brake booster with master cylinder assembly) connector is securely connected.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

3.CHECK AUXILIARY BATTERY

NG

CONNECT CONNECTOR TO BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY CORRECTLY

3.CHECK AUXILIARY BATTERY
a.

Check the auxiliary battery voltage.

Standard Voltage:
Tester Connection Condition Specified Condition
Auxiliary battery Power switch on (IG) 11 to 14 V
Auxiliary battery Power switch on (READY) 11 to 15.5 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)

NG

CHARGE OR REPLACE AUXILIARY BATTERY

4.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)
a.
C343117C91
0.281,0.76 0.688,1.031 0.406,0.271 2.188,1.896 2.333,1 true 0.188,0.188 0.5,0.385 0.313,0.198 10 false *a 0.365,0.813 0.677,1.01 0.313,0.198 10 false A39 2.333,0.823 2.646,1.021 0.313,0.198 10 false IG1
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Turn the power switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



c.

Disconnect the A39 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Turn the power switch on (IG).


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A39-23 (IG1) - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (GND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)

5.CHECK HARNESS AND CONNECTOR (GND TERMINAL)
a.
C343117C92
0.313,0.781 0.688,1.031 0.375,0.25 2.469,1.823 2.302,0.896 true 2.115,2.948 2.479,2.094 true 0.25,0.208 0.563,0.406 0.313,0.198 10 false *a 0.385,0.823 0.698,1.021 0.313,0.198 10 false A39 2.167,0.719 2.583,0.938 0.417,0.219 10 false GND1 1.927,2.979 2.417,3.188 0.49,0.208 10 false GND2
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Turn the power switch off.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A39-26 (GND1) - Body ground Always Below 1 Ω
A39-39 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.READ VALUE USING GTS (ABS WARNING LIGHT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)

6.READ VALUE USING GTS (ABS WARNING LIGHT)
a.

Reconnect the A39 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Select the Data List on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ABS Warning Light ABS warning light ON or OFF ON: Warning light on
OFF: Warning light off
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
ABS Warning Light
50003 105 51

c.

Check the GTS display condition of the ABS warning light.


Result:
Result Proceed to
ON is displayed. (for LHD) A
ON is displayed. (for RHD) B
OFF is displayed. C



A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C