Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM32K0E _54 Brake _060044 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0294924 ELECTRONICALLY CONTROLLED BRAKE SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  Brake Control Warning Light Remains ON  


DESCRIPTION

The skid control ECU (brake booster with master cylinder assembly) is connected to the combination meter assembly via CAN communication.

If the skid control ECU (brake booster with master cylinder assembly) stores a DTC, the brake warning light / yellow (minor malfunction) comes on in the combination meter assembly.

WIRING DIAGRAM

C270526E98
0.073,4.083 1.906,4.49 1.833,0.406 10 false Combination Meter Assembly (Meter Circuit Plate) 4.979,3.938 7.083,4.552 2.104,0.615 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 5.948,1.021 6.333,1.354 0.385,0.333 10 false CA1L 0.885,1.021 1.344,1.323 0.458,0.302 10 false CANL 5.958,1.938 6.365,2.26 0.406,0.323 10 false CA1H 0.885,1.938 1.333,2.229 0.448,0.292 10 false CANH 2.844,3.375 4.583,3.635 1.74,0.26 10 false : CAN Communication Line 0.083,3.906 0.396,4.104 0.313,0.198 10 false F4 1.385,0.833 1.719,1.115 0.333,0.281 10 false 31 1.385,1.76 1.74,2.052 0.354,0.292 10 false 32 5.688,0.854 6,1.052 0.313,0.198 10 false 42 5.677,1.76 5.99,1.958 0.313,0.198 10 false 43 4.99,3.75 5.531,4.073 0.542,0.323 10 false A39

CAUTION / NOTICE / HINT

NOTICE:

After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

2.CHECK IF BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY CONNECTOR IS SECURELY CONNECTED

B

2.CHECK IF BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU (brake booster with master cylinder assembly) connector is securely connected.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

3.CHECK AUXILIARY BATTERY

NG

CONNECT CONNECTOR TO BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY CORRECTLY

3.CHECK AUXILIARY BATTERY
a.

Check the auxiliary battery voltage.

Standard Voltage:
Tester Connection Condition Specified Condition
Auxiliary battery Power switch on (IG) 11 to 14 V
Auxiliary battery Power switch on (READY) 11 to 15.5 V



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (BRAKE WARNING LIGHT / YELLOW (MINOR MALFUNCTION))

NG

CHARGE OR REPLACE AUXILIARY BATTERY

4.READ VALUE USING GTS (BRAKE WARNING LIGHT / YELLOW (MINOR MALFUNCTION))
a.

Select the Data List on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ECB Warning Light Brake warning light / yellow (minor malfunction) ON or OFF ON: Warning light on
OFF: Warning light off
ECB: Electronically Controlled Brake System
Chassis > ABS/VSC/TRC > Data List
Tester Display
ECB Warning Light
50003 105 57

b.

Check the GTS display condition of the brake warning light / yellow (minor malfunction).


Result:
Result Proceed to
ON is displayed. (for LHD) A
ON is displayed. (for RHD) B
OFF is displayed. C



A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C