Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM32K0E _54 Brake _060044 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0294924 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1349  Pressure Holding Solenoid Valve Learning Undone  C134A  Pressure Holding Solenoid Valve Learning Malfunction  


DESCRIPTION

The skid control ECU (brake booster with master cylinder assembly) stores the individual characteristic of each holding solenoid built into the brake actuator assembly. Based on the stored information, the skid control ECU (brake booster with master cylinder assembly) calibrates the individual differences and controls systems.

The skid control ECU (brake booster with master cylinder assembly) receives the shift position P signal from the hybrid vehicle control ECU through the CAN communication system.

These DTCs are cleared when the ABS holding solenoid valve learning results are normal.

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1349 Pressure Holding Solenoid Valve Learning Undone 1155 The ABS holding solenoid valve learning value is not stored. Perform ABS holding solenoid valve learning and check for DTCs. If no DTCs are output again, the valve is normal. Electronically controlled brake system DTC
HINT:

During test mode, related DTCs are cleared.


C134A Pressure Holding Solenoid Valve Learning Malfunction 1156 The ABS holding solenoid valve learning value cannot be obtained.
·

Perform ABS holding solenoid valve learning and check for DTCs. If no DTCs are output again, the valve is normal.

·

Skid control ECU (brake booster with master cylinder assembly)

·

Brake actuator assembly


Electronically controlled brake system DTC

CAUTION / NOTICE / HINT

NOTICE:

After replacing the skid control ECU (brake booster with master cylinder assembly) or brake actuator assembly, perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION


HINT:

Before performing linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization, DTC C1203 will be output.


PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the power switch off.


c.

Turn the power switch on (IG).


d.

Check that DTCs other than C1345, C1349 and C1392 are not output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
OK:

DTCs other than C1345, C1349 and C1392 are not output.



Result:
Proceed to
OK
NG



OK

2.PERFORM AIR BLEEDING

NG

2.PERFORM AIR BLEEDING
a.

Perform the air bleeding procedure in Bleed Brake System.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID>BLEEDING


Result:
Proceed to
NEXT



NEXT

3.PERFORM ABS HOLDING SOLENOID VALVE LEARNING
3.PERFORM ABS HOLDING SOLENOID VALVE LEARNING
a.

Turn the power switch off.


b.

Check and ensure the following conditions required for performing ABS holding solenoid valve learning and then perform ABS holding solenoid valve learning.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION

Chassis > ABS/VSC/TRC > Utility
Tester Display
ECB Utility
50005 105 167
1.

The auxiliary battery voltage is 11 to 15.5 V when the power switch is on (READY).

2.

The brake actuator assembly is not hot.

3.

The hybrid control system is not malfunctioning.

4.

The shift lever is in P.

5.

The READY light in the combination meter assembly is illuminated.

6.

The brake pedal is not depressed.

7.

The parking brake is released.


NOTICE:

Learning will be performed in the order of linear solenoid valve offset learning and then ABS holding solenoid valve learning.



Result:
Proceed to
NEXT



NEXT

4.RECONFIRM DTC
4.RECONFIRM DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the power switch off.


c.

Turn the power switch on (IG).


d.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTCs C1349 and C134A are not output. A
DTCs C1349 and/or C134A are output. B



A

END

B

5.PERFORM ACTIVE TEST USING GTS (ABS SOLENOID)
5.PERFORM ACTIVE TEST USING GTS (ABS SOLENOID)
a.

Select the Active Test on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
ABS Solenoid (SRLH) Holding solenoid valve (RLH) Solenoid ON/OFF -
ABS Solenoid (SRRH) Holding solenoid valve (RRH) Solenoid ON/OFF -
ABS Solenoid (SFLH) Holding solenoid valve (FLH) Solenoid ON/OFF -
ABS Solenoid (SFRH) Holding solenoid valve (FRH) Solenoid ON/OFF -
Chassis > ABS/VSC/TRC > Active Test
Tester Display
ABS Solenoid (SRLH)
50004 105 21
Chassis > ABS/VSC/TRC > Active Test
Tester Display
ABS Solenoid (SRRH)
50004 105 19
Chassis > ABS/VSC/TRC > Active Test
Tester Display
ABS Solenoid (SFLH)
50004 105 17
Chassis > ABS/VSC/TRC > Active Test
Tester Display
ABS Solenoid (SFRH)
50004 105 15

b.

Operate the SFRH (front right wheel holding solenoid valve), SFLH (front left wheel holding solenoid valve), SRRH (rear right wheel holding solenoid valve) and SRLH (rear left wheel holding solenoid valve) solenoids one by one. While operating each solenoid, depress the brake pedal, open the corresponding bleeder plug and check that brake fluid does not flow from the bleeder plug.

OK:

Brake fluid does not flow from the corresponding bleeder plug when the brake pedal is depressed when operating each solenoid.



c.

While not operating the SFRH (front right wheel holding solenoid valve), SFLH (front left wheel holding solenoid valve), SRRH (rear right wheel holding solenoid valve) and SRLH (rear left wheel holding solenoid valve) solenoids, depress the brake pedal, open each bleeder plug and check that brake fluid flows from each bleeder plug.

OK:

Brake fluid flows from each bleeder plug when not operating each solenoid and the brake pedal is depressed.



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG (for LHD) C
NG (for RHD) D



A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C

D