Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › 2016.10–2018.05
RM32K0E _54 Brake _060044 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0294924 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1427  Malfunction in Motor  


DESCRIPTION

When the power switch is on (READY), the stop light switch assembly off and the vehicle speed is 20 km/h (12 mph) or more, the skid control ECU (brake booster with master cylinder assembly) performs a self-diagnosis of the ABS motor relay circuit during the initial check of the actuator.

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1427 Malfunction in Motor 1159 The pump motor built into the brake actuator assembly is not operating correctly.
·

Wire harness or connector

·

Pump motor or pump motor circuit built into the brake actuator assembly


Electronically controlled brake system DTC

WIRING DIAGRAM

C353485E03
1.74,0.427 2.271,0.771 0.531,0.344 10 false 41 1.979,0.656 2.51,1 0.531,0.344 10 false BM 0.75,0.677 1.906,1.104 1.156,0.427 10 false ABS MTR NO. 3 0.156,2.115 1.542,2.563 1.385,0.448 10 false from Auxiliary Battery 0.188,2.771 1.927,3.448 1.74,0.677 10 false *1: for LHD 2.104,2.969 2.635,3.313 0.531,0.344 10 false A39 2.104,3.135 4.156,3.563 2.052,0.427 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 2.177,1.948 2.708,2.292 0.531,0.344 10 false IC 3.042,0.917 3.771,1.375 0.729,0.458 10 false ABS Motor Relay 4.448,1.021 4.979,1.365 0.531,0.344 10 false 40 5.01,1.125 5.542,1.469 0.531,0.344 10 false A40 5.021,0.906 5.552,1.25 0.531,0.344 10 false 13 5.406,1.125 5.938,1.469 0.531,0.344 10 false A41 5.052,1.354 5.583,1.698 0.531,0.344 10 false *1 5.469,1.354 6,1.698 0.531,0.344 10 false *2 5.823,2.615 6.354,2.958 0.531,0.344 10 false MGND 5.427,2.99 7.115,3.458 1.688,0.469 10 false Brake Actuator Assembly 4.021,1.25 4.552,1.594 0.531,0.344 10 false +BM 5.813,1.25 6.344,1.594 0.531,0.344 10 false +BM 5.448,0.906 5.979,1.25 0.531,0.344 10 false 13 5.083,2.281 5.615,2.625 0.531,0.344 10 false 1 5.5,2.281 6.031,2.625 0.531,0.344 10 false 1 5.438,2.49 5.969,2.833 0.531,0.344 10 false A41 5.01,2.49 5.542,2.833 0.531,0.344 10 false A40 5.479,2.719 6.01,3.063 0.531,0.344 10 false *2 5.042,2.719 5.573,3.063 0.531,0.344 10 false *1 0.188,3.25 1.344,3.615 1.156,0.365 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the skid control ECU (brake booster with master cylinder assembly) or brake actuator assembly, perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (ABS MOTOR RELAY)
a.

Select the Active Test on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Motor Relay ABS motor relay Relay ON/OFF Operating sound of motor can be heard.
Chassis > ABS/VSC/TRC > Active Test
Tester Display
Motor Relay
50004 105 2

b.

Check the operating sound of the ABS motor relay when operating it with the GTS.


Result:
Result Proceed to
The operating sound is heard. A
The operating sound is not heard. B



A

2.RECONFIRM DTC

B

3.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
2.RECONFIRM DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the power switch off.


c.

Turn the power switch on (READY).


d.

Perform a road test.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTC C1427 is not output. A
DTC C1427 is output. (for LHD) B
DTC C1427 is output. (for RHD) C



A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
a.

Turn the power switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the A39 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Disconnect the A40 brake actuator assembly connector (for LHD).


e.

Disconnect the A41 brake actuator assembly connector (for RHD).


f.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
A39-40 (+BM) - A40-13 (+BM) Always Below 1 Ω
A39-40 (+BM) or A40-13 (+BM) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
A39-40 (+BM) - A41-13 (+BM) Always Below 1 Ω
A39-40 (+BM) or A41-13 (+BM) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (GND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (GND TERMINAL)
a.
C346353C17
0.198,0.885 0.563,1.156 0.365,0.271 0.198,0.542 0.563,0.813 0.365,0.271 0.833,1.771 1.021,2.74 true 0.198,0.083 0.51,0.281 0.313,0.198 10 false *a 0.26,0.938 0.573,1.135 0.313,0.198 10 false A41 0.823,2.76 1.417,3 0.594,0.24 10 false MGND 0.25,0.583 0.563,0.781 0.313,0.198 10 false A40 0.625,0.583 0.938,0.781 0.313,0.198 10 false *A 0.625,0.927 0.938,1.125 0.313,0.198 10 false *B
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Brake Actuator Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
A40-1 (MGND) - Body ground Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
A41-1 (MGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)

5.RECONFIRM DTC
a.

Reconnect the A39 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Reconnect the A40 brake actuator assembly connector (for LHD).


c.

Reconnect the A41 brake actuator assembly connector (for RHD).


d.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

e.

Turn the power switch off.


f.

Turn the power switch on (READY).


g.

Perform a road test.


h.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTC C1427 is not output. A
DTC C1427 is output. (for LHD) B
DTC C1427 is output. (for RHD) C



A

B

C