Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM32K0E _54 Brake _060044 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0294924 ELECTRONICALLY CONTROLLED BRAKE SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  Abnormal Brake Pedal Response on First Depression  


DESCRIPTION

If the vehicle has been stopped without opening or closing the driver door for a long period of time, the electronically controlled brake system will not be ready and sufficient fluid pressure may not be stored in the accumulator. In this case, the brake pedal response may not be the same as usual the first time the brake pedal is depressed. This is not a malfunction.

WIRING DIAGRAM

C353486E04
5.104,1.875 5.583,2.208 0.479,0.333 10 false 24 5.344,2.115 5.823,2.448 0.479,0.333 10 false CTY 6.344,1.99 6.823,2.323 0.479,0.333 10 false IC 5.021,3.875 5.5,4.208 0.479,0.333 10 false A39 5.01,4.042 7.083,4.5 2.073,0.458 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 0.333,1.323 2.146,1.781 1.813,0.458 10 false to Main Body ECU (Multiplex Network Body ECU) 1.177,2.229 1.656,2.563 0.479,0.333 10 false M11 1.177,2.396 4.125,2.729 2.948,0.333 10 false Front Door Courtesy Light Switch Assembly LH 1.177,3.406 1.656,3.74 0.479,0.333 10 false M54 3.271,1.844 3.75,2.177 0.479,0.333 10 false 1 3.292,3 3.771,3.333 0.479,0.333 10 false 1 1.177,3.563 4.125,3.896 2.948,0.333 10 false Front Door Courtesy Light Switch Assembly RH 3.698,1.844 4.01,2.094 0.313,0.25 10 false *1 0.354,2.302 0.667,2.552 0.313,0.25 10 false *1 0.354,3.417 0.667,3.667 0.313,0.25 10 false *2 0.688,4.167 1.583,4.5 0.896,0.333 10 false *1: for LHD 2.021,4.167 2.917,4.5 0.896,0.333 10 false *2: for RHD 3.698,3 4.01,3.25 0.313,0.25 10 false *2

CAUTION / NOTICE / HINT

NOTICE:

After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION


PROCEDURE

1.BRAKE PROBLEM CHECK
a.

Check the conditions at the time the problem occurred.

i.

Whether a warning light illuminated or the buzzer sounded.


ii.

The number of times the power switch was turned on (IG) since the latest symptom occurred.


iii.

Frequency of the symptom.



Result:
Proceed to
NEXT



NEXT

2.CHECK DTC
2.CHECK DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the power switch off.


c.

Turn the power switch on (IG).


d.

Check the DTCs (electronically controlled brake system) that are output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTCs C1391 and C1256 are not output. A
DTCs C1391 and/or C1256 are output. B



A

3.CHECK VEHICLE

B

3.CHECK VEHICLE
a.

Turn the power switch off.


b.

Depress the brake pedal within 2 minutes of opening the driver door and check the response of the brake pedal.


c.

Release the brake pedal and wait for 2 minutes without depressing the brake pedal, opening or closing the driver door or operating the power switch.


d.

After 2 seconds or more have elapsed, depress the brake pedal and check that the first depression response is different to successive depression responses.

HINT:

Compare the response of the brake pedal when the system is in sleep mode and when the stroke simulator is operating.



Result:
Result Proceed to
The response of the brake pedal does not change. A
The response of the brake pedal changed. B



A

4.INSPECT FRONT DOOR COURTESY LAMP SWITCH ASSEMBLY (FOR DRIVER SIDE)

B

END

4.INSPECT FRONT DOOR COURTESY LAMP SWITCH ASSEMBLY (FOR DRIVER SIDE)
a.

Set the interior light door switch to ON and check that the map light assembly illuminates, then set the interior light door switch to DOOR.


b.

Check that the map light assembly illuminates when the driver door is opened.

OK:

The map light assembly illuminates when the driver door is opened.



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (CTY TERMINAL)

NG

INSPECT LIGHTING SYSTEM (COURTESY LIGHT SWITCH CIRCUIT)

5.CHECK HARNESS AND CONNECTOR (CTY TERMINAL)
a.
C343117C93
0.281,0.76 0.688,1.031 0.406,0.271 2.292,1.885 2.438,0.99 true 0.188,0.188 0.5,0.385 0.313,0.198 10 false *a 0.365,0.802 0.677,1 0.313,0.198 10 false A39 2.406,0.823 2.823,1.052 0.417,0.229 10 false CTY
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A39 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A39-24 (CTY) - Body ground Driver door open Below 1.5 V
A39-24 (CTY) - Body ground Driver door closed 11 to 14 V



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR (CTY CIRCUIT)