Troubleshooting for when abnormal sound occurs from the engine compartment due to air when the brake pedal is depressed.
After replacing the brake booster with master cylinder assembly, perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION
Clear the DTCs.
Turn the power switch off.
Turn the power switch on (IG).
Check the DTCs that are output.
| Result | Proceed to |
|---|---|
| DTCs are not output. | A |
| DTCs are output. | B |
A
B
Perform the air bleeding procedure in Bleed Brake System.
| Proceed to |
|---|
| NEXT |
NEXT
Depress the brake pedal and check if the symptom disappeared.
| Result | Proceed to |
|---|---|
| The symptom disappeared (abnormal sound does not occur). | A |
| The symptom does not disappear (abnormal sound occurs). | B |
A
B
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check that the following conditions required to perform "forced actuator refresh" are met and perform "forced actuator refresh" using the GTS.
The shift lever is in P.
The parking brake is applied.
Vehicle speed is 0 km/h (0 mph).
The brake pedal is not depressed.
The READY light in the combination meter assembly is illuminated (or the power switch is on (IG) while the auxiliary battery is being backed up with a power supply).
| Tester Display |
|---|
| Forced Actuator Refresh |
As brake fluid pressure is being generated while performing "forced actuator refresh", do not depress the brake pedal or perform a brake system related procedure.
While performing "forced actuator refresh", the accumulator pressure may decrease and the meter buzzer may sound.
After "forced actuator refresh" has completed, check the time taken to perform the "forced actuator refresh" displayed on the GTS.
The time taken to perform "forced actuator refresh" is 10 minutes and 50 seconds or more.
| Proceed to |
|---|
| OK |
| NG |
If the time taken to perform "forced actuator refresh" is less than 10 minutes and 50 seconds, "forced actuator refresh" may have canceled without completing properly. In this case, check the conditions required to perform "forced actuator refresh" are met and perform "forced actuator refresh" again.
OK
NG
Depress the brake pedal and check if the symptom disappeared.
| Result | Proceed to |
|---|---|
| The symptom disappeared (abnormal sound does not occur). | A |
| The symptom does not disappear (abnormal sound occurs). | B |
A
B
Clear the DTCs.
As DTC C1256 (Accumulator Low Pressure) may be stored by performing "forced actuator refresh", clear the DTCs after performing "forced actuator refresh".
| Proceed to |
|---|
| NEXT |
NEXT
Check that the following conditions required to perform "forced actuator refresh" are met and perform "forced actuator refresh" using the GTS.
The shift lever is in P.
The parking brake is applied.
Vehicle speed is 0 km/h (0 mph).
The brake pedal is not depressed.
The READY light in the combination meter assembly is illuminated (or the power switch is on (IG) while the auxiliary battery is being backed up with a power supply).
| Tester Display |
|---|
| Forced Actuator Refresh |
As brake fluid pressure is being generated while performing "forced actuator refresh", do not depress the brake pedal or perform a brake system related procedure.
While performing "forced actuator refresh", the accumulator pressure may decrease and the meter buzzer may sound.
After "forced actuator refresh" has completed, check the time taken to perform the "forced actuator refresh" displayed on the GTS.
The time taken to perform "forced actuator refresh" is 10 minutes and 50 seconds or more.
| Proceed to |
|---|
| OK |
| NG |
If the time taken to perform "forced actuator refresh" is less than 10 minutes and 50 seconds, "forced actuator refresh" may have canceled without completing properly. In this case, check the conditions required to perform "forced actuator refresh" are met and perform "forced actuator refresh" again.
OK
NG
Depress the brake pedal and check if the symptom disappeared.
| Result | Proceed to |
|---|---|
| The symptom disappeared (abnormal sound does not occur). | A |
| The symptom does not disappear (abnormal sound occurs). | B |
A
B
Clear the DTCs.
As DTC C1256 (Accumulator Low Pressure) may be stored by performing "forced actuator refresh", clear the DTCs after performing "forced actuator refresh".
| Proceed to |
|---|
| NEXT |
NEXT
Check that the following conditions required to perform "forced actuator refresh" are met and perform "forced actuator refresh" using the GTS.
The shift lever is in P.
The parking brake is applied.
Vehicle speed is 0 km/h (0 mph).
The brake pedal is not depressed.
The READY light in the combination meter assembly is illuminated (or the power switch is on (IG) while the auxiliary battery is being backed up with a power supply).
| Tester Display |
|---|
| Forced Actuator Refresh |
As brake fluid pressure is being generated while performing "forced actuator refresh", do not depress the brake pedal or perform a brake system related procedure.
While performing "forced actuator refresh", the accumulator pressure may decrease and the meter buzzer may sound.
After "forced actuator refresh" has completed, check the time taken to perform the "forced actuator refresh" displayed on the GTS.
The time taken to perform "forced actuator refresh" is 10 minutes and 50 seconds or more.
| Proceed to |
|---|
| OK |
| NG |
If the time taken to perform "forced actuator refresh" is less than 10 minutes and 50 seconds, "forced actuator refresh" may have canceled without completing properly. In this case, check the conditions required to perform "forced actuator refresh" are met and perform "forced actuator refresh" again.
OK
NG
Depress the brake pedal and check if the symptom disappeared.
| Result | Proceed to |
|---|---|
| The symptom disappeared (abnormal sound does not occur). | A |
| The symptom does not disappear (abnormal sound occurs). (for LHD) | B |
| The symptom does not disappear (abnormal sound occurs). (for RHD) | C |
If the symptom does not disappear even after "forced actuator refresh" has completed properly 3 times, replace the brake booster with master cylinder assembly.
A
B
C
Clear the DTCs.
As DTC C1256 (Accumulator Low Pressure) may be stored by performing "forced actuator refresh", clear the DTCs after performing "forced actuator refresh".
| Proceed to |
|---|
| NEXT |
NEXT