Home › Engine / Hybrid System › 2ZR-FXE (ENGINE CONTROL) › SFI SYSTEM
RM32K0E _51 Engine / Hybrid System _060312 2ZR-FXE ENGINE CONTROL _0295698 SFI SYSTEM C

2ZR-FXE ENGINE CONTROL  SFI SYSTEM  P01052A  Manifold Absolute Pressure / Barometric Pressure Sensor Signal Stuck in Range  


DESCRIPTION

Refer to DTC P010511.

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>P010511

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P01052A Manifold Absolute Pressure / Barometric Pressure Sensor Signal Stuck in Range Intake manifold pressure measured after engine start drops by less than 2 kPa (0.3 psi) compared to the intake manifold pressure (atmospheric pressure) measured before engine start (2 trip detection logic).
·

Intake system

·

Manifold absolute pressure sensor


Comes on DTC stored SAE Code: P0106

MONITOR DESCRIPTION

When the intake manifold pressure measured after engine start drops by less than 2 kPa [0.3 psi] compared to the intake manifold pressure (atmospheric pressure) measured before engine start, the ECM interprets this as a malfunction of the manifold absolute pressure sensor and stores DTC P01052A.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the power switch off and wait for at least 30 seconds.

6.

Turn the power switch on (IG).

7.

Turn the GTS on.

8.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

9.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher.

10.

Move the shift lever to N.

11.

Idle the engine for 10 seconds or more.

12.

Enter the following menus: Powertrain / Engine / Trouble Codes.

13.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



14.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

15.

Input the DTC: P01052A.

16.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.

·

If the judgment result is INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P01052A)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P01052A is output A
DTC P01052A and other DTCs are output B


HINT:

If any DTCs other than P01052A are output, troubleshoot those DTCs first.




A

2.READ VALUE USING GTS (INTAKE MANIFOLD ABSOLUTE PRESSURE)

B

2.READ VALUE USING GTS (INTAKE MANIFOLD ABSOLUTE PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Intake Manifold Absolute Pressure and Engine Independent.

Powertrain > Engine > Data List
Tester Display
Intake Manifold Absolute Pressure
Engine Independent
50003 372 385,428

e.

Read the value of Intake Manifold Absolute Pressure.


f.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 397 2103

g.

Start the engine.


h.

Confirm that the value of Data List item Engine Independent is "Operate" then check the value of Intake Manifold Absolute Pressure.

Standard:
Engine Condition GTS Display
Engine Independent Intake Manifold Absolute Pressure
Power switch on (IG) (Engine stopped) - 80 to 110 kPa (11.6 to 15.95 psi)
Idling Operate 20 to 40 kPa (2.9 to 5.8 psi)


HINT:

If the value of Data List item Engine Independent is "Not Opr" when the engine is idling, charge control is being performed. Check the Intake Manifold Absolute Pressure after charge control is complete ("Operate" is displayed).



Result:
Proceed to
OK
NG



OK

NG

3.CHECK INTAKE SYSTEM
3.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leaks.

Click hereEngine / Hybrid System>2ZR-FXE (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION

OK:

No leaks from intake system.


HINT:

Perform "Inspection After Repair" after repairing or replacing the intake system.

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

NG

REPAIR OR REPLACE INTAKE SYSTEM