Home › Engine / Hybrid System › 2ZR-FXE (ENGINE CONTROL) › MASS AIR FLOW METER
RM32K0E _51 Engine / Hybrid System _060312 2ZR-FXE ENGINE CONTROL _0295703 MASS AIR FLOW METER G

2ZR-FXE ENGINE CONTROL  MASS AIR FLOW METER  INSPECTION  


PROCEDURE

Hide 22204 1.INSPECT MASS AIR FLOW METER

a.

Check the output voltage.

i.
A357485C01
2.74,1.698 2.833,1.25 2.833,1.25 2.917,1.25 true 2.25,2.333 2.25,2.167 2.25,2.167 2.573,1.75 true 1.75,1.417 1.917,1.417 1.917,1.417 2.438,1.729 true 2.958,1.156 3.406,1.385 0.448,0.229 10 false 1 (+B) 2.031,2.375 2.604,2.635 0.573,0.26 10 false 2 (E2G) 1.313,1.302 1.76,1.531 0.448,0.229 10 false 3 (VG) 0.083,0.094 0.396,0.292 0.313,0.198 10 false *a
*a Component without harness connected
(Mass Air Flow Meter)
V100135

Air


Connect a battery positive (+) lead to terminal 1 (+B) and negative (-) lead to terminal 2 (E2G).

NOTICE:

While using the battery during inspection, do not bring the positive and negative tester probes too close to each other as a short circuit may occur.



ii.

Connect the positive (+) tester probe to terminal 3 (VG) and negative (-) tester probe to terminal 2 (E2G).


iii.

Blow air into the mass air flow meter and check that the voltage fluctuates.

If the result is not as specified, replace the mass air flow meter.



b.
A354279C01
1.729,2.26 2.188,2.26 true 2.469,2.229 2.813,2.229 true 1.563,2.156 1.875,2.313 0.313,0.156 10 false *a 2.854,2.146 3.167,2.302 0.313,0.156 10 false *b
*a Platinum Hot Wire (Heater)
*b Temperature Sensor (Thermistor)


Perform a visual check for any foreign matter on the platinum hot wire (heater) and temperature sensor (thermistor) of the mass air flow meter shown in the illustration.

OK:

There is no foreign matter.


If the result is not as specified, replace the mass air flow meter.


c.
A167890C07
0.802,0.958 1.063,0.958 1.063,0.958 1.333,1.458 true 1.594,1.469 1.823,0.958 1.823,0.958 2.146,0.958 true 1.344,1.448 1.448,1.594 0.104,0.146 10 false 5 1.5,1.448 1.604,1.594 0.104,0.146 10 false 4 1.656,1.448 1.76,1.594 0.104,0.146 10 false 3 1.958,1.448 2.063,1.594 0.104,0.146 10 false 1 1.802,1.448 1.906,1.594 0.104,0.146 10 false 2 2.188,0.875 2.604,1.073 0.417,0.198 10 false THA 0.594,0.875 0.854,1.052 0.26,0.177 10 false E2 0.063,0.052 0.24,0.219 0.177,0.167 10 false *a
*a Component without harness connected
(Mass Air Flow Meter)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (THA) - 5 (E2) -20°C (-4°F) 12.5 to 16.9 kΩ
20°C (68°F) 2.19 to 2.67 kΩ
60°C (140°F) 0.50 to 0.68 kΩ


If the result is not as specified, replace the mass air flow meter.