Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › 2016.10–2019.09
RM32K0E _56 Audio / Visual / Telematics _060599 PARK ASSIST / MONITORING _0297239 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  U0232  Lost Communication with Blind Spot Monitor Slave Module  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor LH (Master) judges that there is a communication problem with the blind spot monitor sensor RH (Slave).

DTC No. Detection Item DTC Detection Condition Trouble Area
U0232 Lost Communication with Blind Spot Monitor Slave Module The blind spot monitor sensor (master) cannot receive signals from the blind spot monitor sensor (slave)
·

Open or short in CAN bus main wire or connector

·

Blind spot monitor sensor RH (Slave)

·

Power source circuit of blind spot monitor sensor RH (Slave)

·

Blind spot monitor sensor RH (Slave) ground circuit

·

Blind spot monitor sensor LH (Master)



WIRING DIAGRAM

E334367E25
2.844,2.646 4.51,3.302 1.667,0.656 10 false Blind Spot Monitor Sensor RH (Slave) 0.417,1.271 1.438,1.885 1.021,0.615 10 false from IG1 NO. 1 Relay 1.906,1.448 2.927,2.063 1.021,0.615 10 false ECU-IG1 NO. 4 3.188,1.302 4.208,1.917 1.021,0.615 10 false BRB 3.198,1.938 3.75,2.198 0.552,0.26 10 false BRGD 2.844,2.479 3.135,2.688 0.292,0.208 10 false M63 5.333,2.5 5.625,2.708 0.292,0.208 10 false M62 5.719,1.875 6.135,2.115 0.417,0.24 10 false CA2N 3.802,1.844 4.219,2.083 0.417,0.24 10 false CA2N 3.813,1.01 4.229,1.25 0.417,0.24 10 false CA2P 5.708,0.969 6.125,1.208 0.417,0.24 10 false CA2P 4.25,1.021 4.667,1.26 0.417,0.24 10 false 1 5.5,1 5.917,1.24 0.417,0.24 10 false 1 5.542,1.833 5.958,2.073 0.417,0.24 10 false 6 4.229,1.823 4.646,2.063 0.417,0.24 10 false 6 3.031,1.156 3.448,1.396 0.417,0.24 10 false 5 2.938,1.813 3.354,2.052 0.417,0.24 10 false 10 5.344,2.656 7.01,3.313 1.667,0.656 10 false Blind Spot Monitor Sensor LH (Master)

CAUTION / NOTICE / HINT

NOTICE:
·

When checking for DTCs, make sure that the blind spot monitor system is on.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK CAN BUS MAIN WIRE
a.
E369203C02
1.531,0.167 1.938,0.406 0.406,0.24 1.531,1.76 1.938,2 0.406,0.24 2.167,1 2.583,0.583 2.583,0.583 2.75,0.583 true 2.167,1.167 2.583,1.5 2.583,1.5 2.75,1.5 true 0.938,1.948 1.104,1.948 1.104,1.948 1.635,2.417 true 2.25,2.833 2.5,3.167 2.5,3.167 2.667,3.167 true 1.615,0.188 2.073,0.385 0.458,0.198 10 false M62 1.594,1.802 2.052,2 0.458,0.198 10 false F41 2.833,0.5 3.292,0.698 0.458,0.198 10 false CA2P 2.833,1.417 3.292,1.615 0.458,0.198 10 false CA2N 0.656,1.885 1.115,2.083 0.458,0.198 10 false CG 2.792,3.083 3.25,3.281 0.458,0.198 10 false BAT 0.125,0.135 0.583,0.333 0.458,0.198 10 false *a 0.167,1.677 0.625,1.875 0.458,0.198 10 false *b
*a Component with harness connected
(Blind Spot Monitor Sensor LH (Master))
*b DLC3


Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
M62-1 (CA2P) -M62-6 (CA2N) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω Below 54 Ω: Short circuit between bus lines
70 Ω or more: Open circuit in main bus lines
M62-1(CA2P) - F41-4(CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CA2P short to ground
M62-6(CA2N) - F41-4(CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CA2N short to ground
M62-1(CA2P) - F41-16(BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CA2P +B short
M62-6(CA2N) - F41-16(BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CA2N +B short



Result:
Result Proceed to
OK A
Open circuit in CAN main bus lines B
Short circuit between bus lines C
·

Short to ground

·

+B short


D



A

2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH (SLAVE) - BODY GROUND)

B

6.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR RH (SLAVE))

C

8.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH (SLAVE))

D

10.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH (SLAVE))
2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH (SLAVE) - BODY GROUND)
a.
E263038C97
1.615,0.292 1.958,0.51 0.344,0.219 2.49,1.906 2.333,1.906 2.333,1.906 1.99,1.354 true 0.135,0.104 0.448,0.302 0.313,0.198 10 false *a 1.667,0.323 1.979,0.521 0.313,0.198 10 false M63 2.573,1.833 3.042,2.01 0.469,0.177 10 false BRGD
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH (Slave))


Disconnect the blind spot monitor sensor RH (Slave) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M63-10 (BRGD) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH (SLAVE) POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH (SLAVE) POWER SOURCE)
a.
E263038C98
1.5,0.271 1.854,0.5 0.354,0.229 1.979,1.167 2.49,0.531 2.49,0.531 2.688,0.531 true 0.083,0.052 0.396,0.25 0.313,0.198 10 false *a 1.563,0.323 1.875,0.521 0.313,0.198 10 false M63 2.75,0.448 3.156,0.635 0.406,0.188 10 false BRB
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH (Slave))


Disconnect the blind spot monitor sensor RH (Slave) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M63-5 (BRB) - Body ground Ignition switch to ON 11 to 14 V
M63-5 (BRB) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

4.CHECK DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK DTC
a.

Turn the engine switch off.


b.

Turn the engine switch on (IG).


c.

Check for DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Blind Spot Monitor Master > Trouble Codes
50001 313
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

5.REPLACE BLIND SPOT MONITOR SENSOR RH (SLAVE)
5.REPLACE BLIND SPOT MONITOR SENSOR RH (SLAVE)
a.

Replace the blind spot monitor sensor RH (Slave).

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SENSOR>REMOVAL


b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Blind Spot Monitor Master > Clear DTCs
50002 313

c.

Recheck for DTCs and check if the same DTC is output again.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Blind Spot Monitor Master > Trouble Codes
50001 313
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END (BLIND SPOT MONITOR SENSOR RH (SLAVE) WAS DEFECTIVE)

NG

REPLACE BLIND SPOT MONITOR SENSOR LH (MASTER)

6.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR RH (SLAVE))
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the blind spot monitor sensor RH (Slave) connector.


c.
C373869C13
1.521,0.25 1.885,0.438 0.365,0.188 0.698,1.448 0.854,1.448 0.854,1.448 1.417,1.042 true 1.781,1.844 1.615,1.844 1.615,1.844 1.448,1.177 true 0.167,0.146 0.479,0.344 0.313,0.198 10 false *a 1.583,0.271 1.896,0.469 0.313,0.198 10 false M63 0.313,1.365 0.708,1.542 0.396,0.177 10 false CA2P 1.896,1.792 2.313,1.958 0.417,0.167 10 false CA2N
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH (Slave))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M63-1 (CA2P) - M63-6 (CA2N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

7.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR LH (MASTER))
7.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR LH (MASTER))
a.

Reconnect the blind spot monitor sensor RH (Slave) M63 connector.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Disconnect the blind spot monitor sensor LH (Master) connector.


d.
C373869C14
1.49,0.25 1.885,0.469 0.396,0.219 0.74,1.573 0.917,1.573 0.917,1.573 1.396,1.031 true 1.854,1.865 1.656,1.865 1.656,1.865 1.438,1.219 true 0.146,0.115 0.458,0.313 0.313,0.198 10 false *a 1.594,0.281 1.906,0.479 0.313,0.198 10 false M62 0.365,1.521 0.802,1.719 0.438,0.198 10 false CA2P 1.927,1.792 2.365,1.99 0.438,0.198 10 false CA2N
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH (Master))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M62-1 (CA2P) -M62-6 (CA2N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE BLIND SPOT MONITOR SENSOR LH (MASTER)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR LH (MASTER) - BLIND SPOT MONITOR SENSOR RH (SLAVE))

8.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH (SLAVE))
a.
C373869C15
1.521,0.25 1.885,0.438 0.365,0.188 0.698,1.448 0.854,1.448 0.854,1.448 1.417,1.042 true 1.781,1.844 1.615,1.844 1.615,1.844 1.448,1.177 true 0.167,0.146 0.479,0.344 0.313,0.198 10 false *a 1.583,0.271 1.896,0.469 0.313,0.198 10 false M63 0.313,1.365 0.708,1.542 0.396,0.177 10 false CA2P 1.896,1.792 2.313,1.958 0.417,0.167 10 false CA2N
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH (Slave))


Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the blind spot monitor sensor RH (Slave) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M63-1 (CA2P) - M63-6 (CA2N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

9.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH (MASTER))
9.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH (MASTER))
a.

Reconnect the blind spot monitor sensor RH (Slave) M63 connector.


b.
C373869C16
1.49,0.25 1.885,0.469 0.396,0.219 0.74,1.573 0.917,1.573 0.917,1.573 1.396,1.031 true 1.854,1.865 1.656,1.865 1.656,1.865 1.438,1.219 true 0.146,0.115 0.458,0.313 0.313,0.198 10 false *a 1.563,0.281 1.875,0.479 0.313,0.198 10 false M62 0.365,1.521 0.802,1.719 0.438,0.198 10 false CA2P 1.927,1.792 2.365,1.99 0.438,0.198 10 false CA2N
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH (Master))


Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Disconnect the blind spot monitor sensor LH (Master) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M62-1 (CA2P) - M62-6 (CA2N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE BLIND SPOT MONITOR SENSOR LH (MASTER)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR LH (MASTER) - BLIND SPOT MONITOR SENSOR RH (SLAVE))

10.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH (SLAVE))
a.
E334330C27
1.479,1.813 1.875,2.104 0.396,0.292 1.396,0.198 1.792,0.49 0.396,0.292 0.75,0.781 0.938,0.781 0.938,0.781 1.385,1.063 true 0.75,1.49 0.938,1.49 0.938,1.49 1.365,1.229 true 1,2 1.167,2 1.167,2 1.646,2.365 true 2.25,2.833 2.438,3.135 2.438,3.135 2.552,3.135 true 0.24,1.896 0.552,2.052 0.313,0.156 10 false *b 0.177,0.198 0.49,0.354 0.313,0.156 10 false *a 1.583,1.865 1.896,2.063 0.313,0.198 10 false F41 1.49,0.25 1.802,0.448 0.313,0.198 10 false M63 0.333,0.708 0.948,0.906 0.615,0.198 10 false CA2P 0.344,1.406 0.958,1.604 0.615,0.198 10 false CA2N 2.635,3.063 3.25,3.26 0.615,0.198 10 false BAT 0.729,1.917 1.344,2.115 0.615,0.198 10 false CG
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH (Slave))
*b DLC3


Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the blind spot monitor sensor RH (Slave) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M63-1 (CA2P) - F41-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
M63-6 (CA2N) - F41-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
M63-1 (CA2P) - F41-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
M63-6 (CA2N) - F41-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

11.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH (MASTER))
11.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH (MASTER))
a.

Reconnect the blind spot monitor sensor RH (Slave) M63 connector.


b.
E334330C28
1.479,1.813 1.875,2.104 0.396,0.292 1.396,0.198 1.792,0.49 0.396,0.292 0.75,0.781 0.938,0.781 0.938,0.781 1.375,1.052 true 0.75,1.49 0.938,1.49 0.938,1.49 1.365,1.229 true 1,2 1.167,2 1.167,2 1.646,2.365 true 2.25,2.833 2.438,3.135 2.438,3.135 2.552,3.135 true 0.24,1.896 0.552,2.052 0.313,0.156 10 false *b 0.177,0.198 0.49,0.354 0.313,0.156 10 false *a 1.583,1.865 1.896,2.063 0.313,0.198 10 false F41 1.49,0.25 1.802,0.448 0.313,0.198 10 false M62 0.333,0.708 0.948,0.906 0.615,0.198 10 false CA2P 0.344,1.406 0.958,1.604 0.615,0.198 10 false CA2N 2.667,3.052 3.281,3.25 0.615,0.198 10 false BAT 0.698,1.917 1.313,2.115 0.615,0.198 10 false CG
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH (Slave))
*b DLC3


Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Disconnect the blind spot monitor sensor LH (Master) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M62-1 (CA2P) - F41-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
M62-6 (CA2N) - F41-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
M62-1 (CA2P) - F41-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
M62-6 (CA2N) - F41-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE BLIND SPOT MONITOR SENSOR LH (MASTER)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR LH (MASTER) - BLIND SPOT MONITOR SENSOR RH (SLAVE))