Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM
RM32K0E _56 Audio / Visual / Telematics _060599 PARK ASSIST / MONITORING _0297239 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1AB1  Short to +B in Outer Mirror Indicator(Slave)  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor RH (Slave) detects a short to +B in the outer rear view mirror indicator RH.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AB1 Short to +B in Outer Mirror Indicator(Slave)
Both of the following conditions are met:
·

The blind spot monitor system is on


·

The blind spot monitor sensor is not sending voltage to the indicator but the indicator receives voltage above a specified level for a specified period of time


·

Outer mirror RH

·

Outer rear view mirror assembly RH

·

Wire harness or connector

·

Blind spot monitor sensor RH (Slave)



WIRING DIAGRAM

E221720E62
2.563,1.24 2.698,1.396 0.135,0.156 10 false 2 3.51,1.219 3.938,1.5 0.427,0.281 10 false 12 5.375,1.24 5.531,1.427 0.156,0.188 10 false 4 3.031,1.219 3.49,1.396 0.458,0.177 10 false BSR+ 5.573,1.354 5.979,1.51 0.406,0.156 10 false OMIR 3.25,1.729 3.719,1.896 0.469,0.167 10 false - 0.99,2.188 1.365,2.344 0.375,0.156 10 false IND2 0.75,3.385 1.219,3.583 0.469,0.198 10 false I8 5.406,3.396 5.854,3.573 0.448,0.177 10 false M63 2.354,1.333 2.49,1.49 0.135,0.156 10 false + 2.375,1.802 2.51,1.958 0.135,0.156 10 false - 2.563,1.719 2.698,1.875 0.135,0.156 10 false 1 3.51,1.708 3.76,1.917 0.25,0.208 10 false 9 0.979,2.708 3.115,2.875 2.135,0.167 10 false (Outer Mirror RH) 5.406,3.573 6.573,4.042 1.167,0.469 10 false Blind Spot Monitor Sensor RH (Slave) 0.99,2.354 3.396,2.552 2.406,0.198 10 false Outer Rear View Mirror Indicator RH 0.792,3.583 3.167,3.76 2.375,0.177 10 false Outer Rear View Mirror Assembly RH

CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor system is turned on.


PROCEDURE

1.CHECK DTC
a.

Turn the power switch off.


b.

Turn the power switch on (IG).


c.

Recheck for DTCs and check if the same DTC is output again.

Body Electrical > Blind Spot Monitor Slave > Trouble Codes
50001 314
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)
2.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)
a.
E360283C12
1.49,0.167 1.885,0.469 0.396,0.302 1.823,1.052 2.365,0.563 true 0.146,0.104 0.458,0.302 0.313,0.198 10 false *a 1.563,0.24 2.021,0.438 0.458,0.198 10 false M63 2.417,0.458 2.875,0.656 0.458,0.198 10 false OMIR
*a Front view of wire harness connector
(to blind spot monitor sensor RH (Slave))


Disconnect the M63 blind spot monitor sensor RH (Slave) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M63-4 (OMIR) - Body ground Power switch on (IG) Below 1 V



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)
3.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)
a.
E360283C13
1.49,0.167 1.885,0.469 0.396,0.302 1.823,1.052 2.438,0.49 true 0.146,0.104 0.458,0.302 0.313,0.198 10 false *a 1.563,0.24 2.021,0.438 0.458,0.198 10 false M63 2.5,0.302 2.958,0.5 0.458,0.198 10 false OMIR
*a Front view of wire harness connector
(to blind spot monitor sensor RH (Slave))


Disconnect the IND2 outer mirror RH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M63-4 (OMIR) - Body ground Power switch on (IG) Below 1 V



Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)
4.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)
a.
E360283C14
1.49,0.167 1.885,0.469 0.396,0.302 1.844,1.031 2.365,0.615 true 0.146,0.104 0.458,0.302 0.313,0.198 10 false *a 1.563,0.24 2.021,0.438 0.458,0.198 10 false M63 2.417,0.531 2.875,0.729 0.458,0.198 10 false OMIR
*a Front view of wire harness connector
(to blind spot monitor sensor RH (Slave))


Disconnect the I8 outer rear view mirror assembly RH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M63-4 (OMIR) - Body ground Power switch on (IG) Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR