Home › Drivetrain › P610 (HYBRID TRANSMISSION / TRANSAXLE) › TRANSMISSION CONTROL CABLE › 2016.10–2019.09
RM32K0E _52 Drivetrain _059722 P610 HYBRID TRANSMISSION / TRANSAXLE _0298366 TRANSMISSION CONTROL CABLE A

P610 HYBRID TRANSMISSION / TRANSAXLE  TRANSMISSION CONTROL CABLE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the transmission control cable assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Simple intelligent parking assist system*1
Toyota parking assist-sensor system*1
Pre-crash safety system
Initialize back door lock Power door lock control system (Click here)
Gas leak from exhaust system is repaired Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)


CAUTION:
·
A344784

When the engine is hot, do not touch high-temperature areas such as the engine or exhaust pipe.

·

Touching high-temperature areas such as the engine and exhaust pipe could result in burns.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Click hereGeneral>MAINTENANCE>2ZR-FXE AUXILIARY BATTERY>REMOVAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


Hide 3.SECURE VEHICLE

a.

Fully apply the parking brake and chock a wheel.

CAUTION:
·
C332327

Make sure to apply the parking brake and chock a wheel before performing this procedure.

·

If the vehicle is not secure and the shift lever is moved to N, the vehicle may suddenly move, possibly resulting in an accident or serious injury.




Hide 51441 4.REMOVE NO. 1 ENGINE UNDER COVER

Hide 51444A 5.REMOVE REAR ENGINE UNDER COVER LH

Hide 33504F 6.REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY

Hide 7.REMOVE REAR CONSOLE BOX ASSEMBLY

Hide 57533B 8.REMOVE FRONT FLOOR CENTER BRACE

Hide 17410 9.REMOVE FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)

Hide 58151 10.REMOVE FRONT NO. 1 FLOOR HEAT INSULATOR

a.
C364049

Remove 3 nuts and front No. 1 floor heat insulator from the vehicle body.


Hide 33820B 11.REMOVE TRANSMISSION CONTROL CABLE ASSEMBLY

a.

Move the shift lever to N.


b.
C364051C01
0,0 0,0 false
V113147

Remove in this Direction


Disconnect the end of the transmission control cable assembly from the floor shift shift lever assembly.


c.
C364050C01
1.115,1.927 1.448,1.594 true 0.885,1.896 1.073,2.094 0.188,0.198 10 true *1
*1 Slider
V100135

Push
V113147

Remove in this Direction


Push in the slider and remove the transmission control cable from the floor shift shift lever assembly as shown in the illustration.


d.
C365176

Remove the nut to disconnect the transmission control cable assembly from the control shaft lever.


e.

Remove the clip to disconnect the transmission control cable assembly from the No. 1 transmission control cable bracket.


f.
C366448

Disengage the clamp to separate the transmission control cable assembly.


g.

Remove the bolt to disconnect the transmission control cable assembly from the cylinder head cover sub-assembly.


h.
C365141

Remove the nut.


i.

Disengage the guide to disconnect the transmission control cable assembly from the vehicle body.


j.
C365142

Remove the 2 nuts and transmission control cable assembly from the vehicle body.