Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM32K0E _57 Power Source / Network _059857 NETWORKING _0298527 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B1249  Double Locking ECU Communication Stop  


DESCRIPTION

The main body ECU (multiplex network body ECU) stores this DTC when communication with the double lock door control relay assembly stops for 10 seconds or more.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1249 Double Locking ECU Communication Stop No communication between double lock door control relay assembly and main body ECU (multiplex network body ECU) for 10 seconds or more
·

Double lock door control relay assembly

·

Main body ECU (multiplex network body ECU)

·

Instrument panel junction block assembly

·

Wire harness or connector

·

DOOR DBL/L fuse

·

ECU-DCC NO. 2 fuse



WIRING DIAGRAM

B443243E03
0.167,2.229 1.802,2.625 1.635,0.396 10 false Main Body ECU (Multiplex Network Body ECU) 0.167,2.052 0.615,2.313 0.448,0.26 10 false MB 1.927,2.052 3.563,2.448 1.635,0.396 10 false Instrument Panel Junction Block Assembly 1.927,1.885 2.375,2.146 0.448,0.26 10 false 3D 0.396,3.417 3.313,3.646 2.917,0.229 10 false : LIN Communication Line 1.469,1.208 1.917,1.469 0.448,0.26 10 false LIN2 1.865,1.042 2.313,1.302 0.448,0.26 10 false 16 3.125,1.042 3.573,1.302 0.448,0.26 10 false 17 4.573,1.042 5.021,1.302 0.448,0.26 10 false 9 4.771,1.198 5.219,1.458 0.448,0.26 10 false LIN 5.406,0.938 5.854,1.198 0.448,0.26 10 false +B 5.229,1.354 5.677,1.615 0.448,0.26 10 false CPUB 5.313,1.76 5.76,2.021 0.448,0.26 10 false GND 5.708,0.802 6.156,1.063 0.448,0.26 10 false 12 5.708,1.219 6.156,1.479 0.448,0.26 10 false 11 5.708,1.646 6.156,1.906 0.448,0.26 10 false 7 6,1.063 7,1.323 1,0.26 10 false DOOR DBL/L 5.948,1.479 7.094,1.74 1.146,0.26 10 false ECU-DCC NO. 2 4.406,2.177 6,2.573 1.594,0.396 10 false Double Lock Door Control Relay Assembly 4.417,2 4.865,2.26 0.448,0.26 10 false F14 5,0.146 7.156,0.365 2.156,0.219 10 false from Auxiliary Battery

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.



PROCEDURE

1.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.


B426690C08
2.25,1 2.583,1.25 0.333,0.25 5.583,0.833 5.917,1.083 0.333,0.25 2.25,2.083 2.25,1.583 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 2.313,1.052 2.625,1.25 0.313,0.198 10 false MB 5.677,0.885 5.99,1.083 0.313,0.198 10 false 3D 2.135,2.135 2.448,2.333 0.313,0.198 10 false LIN2
*a Component without harness connected (Instrument Panel Junction Block Assembly) - -



b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

HINT:

This inspection is to check the LIN communication line in the instrument panel junction block assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).


Standard Resistance:
Tester Connection Condition Specified Condition
3D-17 - MB-16 (LIN2) Always Below 1 Ω



Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY)

B

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

C

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY)
a.

Disconnect the F14 double lock door control relay assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the power switch from on (IG) to off and wait for 180 seconds or more without operating any switches.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
3D-17 - F14-9 (LIN) Power switch off Below 1 Ω
F14-9 (LIN) or 3D-17 - Body ground Power switch off 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY - AUXILIARY BATTERY, BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY - AUXILIARY BATTERY, BODY GROUND)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F14-12 (+B) - F14-7 (GND) Power Switch off 11 to 14 V
F14-11 (CPUB) - F14-7 (GND) Power Switch off 11 to 14 V



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F14-7 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.REPLACE DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY
a.

Replace the double lock door control relay assembly.

Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL RELAY>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CHECK FOR DTC
5.CHECK FOR DTC
a.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

b.

Recheck for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123
OK:

DTC B1249 is not output.



Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

END (DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY WAS DEFECTIVE)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)