This DTC is stored when LIN communication between the power window regulator motor assembly (for driver door) and main body ECU (multiplex network body ECU) stops for 10 seconds or more.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B2321 | Driver Side Door ECU Communication Stop | No communication between power window regulator motor assembly (for driver door) and main body ECU (multiplex network body ECU) for 10 seconds or more. | ·
Power window regulator motor assembly (for driver door) ·
Main body ECU (multiplex network body ECU) ·
Multiplex network master switch assembly ·
Wire harness or connector ·
POWER fuse |
Inspect the fuses for circuits related to this system before performing the following procedure.
When a power window regulator motor assembly is replaced or removed and reinstalled, it requires initialization.
Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION
If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.
Clear the DTCs.
Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR
Recheck for DTCs.
| Result | Proceed to |
|---|---|
| Only DTC B2321 is output | A |
| DTC B1206 and B2321 are output simultaneously | B |
When DTC B1206 and B2321 are output simultaneously, perform troubleshooting for DTC B1206 first.
A
B
| *a | Component without harness connected
(Multiplex Network Master Switch Assembly) |
Remove the multiplex network master switch assembly.
Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 16 (LIN2) - 17 (LIN1) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD
Disconnect the J2 power window regulator motor assembly (for driver door) connector.
Measure the resistance according to the value(s) in the table below.
Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the power switch from on (IG) to off and wait for 180 seconds or more without operating any switches.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| J6-16 (LIN2) - J2-9 (LIN) | Power Switch off | Below 1 Ω |
| J6-16 (LIN2) or J2-9 (LIN) - Body ground | Power Switch off | 10 kΩ or higher |
for RHD
Disconnect the I2 power window regulator motor assembly (for driver door) connector.
Measure the resistance according to the value(s) in the table below.
Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the power switch from on (IG) to off and wait for 180 seconds or more without operating any switches.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| I6-16 (LIN2) - I2-9 (LIN) | Power Switch off | Below 1 Ω |
| I6-16 (LIN2) or I2-9 (LIN) - Body ground | Power Switch off | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| J2-2 (B) - J2-1 (GND) | Power Switch off | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J2-1 (GND) - Body ground | Always | Below 1 Ω |
for RHD
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| I2-2 (B) - I2-1 (GND) | Power Switch off | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I2-1 (GND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the power window regulator motor assembly (for driver door).
Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR (for Front Door)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR
Recheck for DTCs.
DTC B2321 is not output.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
A
B
C