When an open or short circuit is detected in the transponder key amplifier coil built into the power switch, the certification ECU (smart key ECU assembly) stores this DTC. This DTC is also stored as a history DTC.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
| B2784 | Antenna Coil Open / Short | The transponder key amplifier coil built into the power switch is open (see below) or shorted (determined by communication with certification ECU (smart key ECU assembly)) (1 trip detection logic*).
·
Terminal AGND, VC5, TXCT or CODE circuit is open (including disconnection of the power switch). ·
The transponder key amplifier coil built into the power switch is open. |
·
Power switch ·
Wire harness or connector ·
Certification ECU (smart key ECU assembly) |
DTC output confirmation operation:
With the shift lever in P and the electrical key transmitter sub-assembly held near the power switch, a hybrid control system start operation is performed by pressing and holding the power switch when the transmitter battery is depleted. |
*: Only output while a malfunction is present.
| Vehicle Condition | |||
|---|---|---|---|
| Pattern 1 | Pattern 2 | ||
| Diagnosis Condition | Always | ○ | ○ |
| Malfunction Status | The transponder key amplifier coil built into the power switch is open (determined by communication with certification ECU (smart key ECU assembly)). | ○ | - |
| The transponder key amplifier coil built into the power switch is shorted (determined by communication with certification ECU (smart key ECU assembly)). | - | ○ | |
| Detection Time | - | - | |
| Number of Trips | 1 trip | 1 trip | |
DTC will be output when conditions for either of the patterns in the table above are met.
| Vehicle Condition when Malfunction Detected | Fail-safe Operation when Malfunction Detected |
|---|---|
| Hybrid control system cannot be started when transmitter battery is depleted by holding electrical key transmitter sub-assembly near power switch and pressing and holding power switch with shift lever in P | - |
| DTC No. | Data List and Active Test |
|---|---|
| B2784 | - |
When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.
After performing repairs, confirm that no DTCs are output by performing "DTC Output Confirmation Operation."
Clear the DTCs.
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM>DTC CHECK / CLEAR
Before checking for DTCs, perform "DTC Output Confirmation Operation" procedure.
DTC B2784 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Using an oscilloscope, check the waveform.
| *a | Component with harness connected
(Power Switch) |
*b | Waveform |
| *c | Waveform (detail) | - | - |
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| F59-8 (CODE) - F59-6 (AGND) | Power switch off, power switch pressed with electrical key transmitter sub-assembly held near power switch* | 1 V/DIV., 20 ms./DIV. | Pulse generation
(See waveform) |
| 2 V/DIV., 100 μs./DIV. | Pulse generation
(See waveform (detail)) |
*: Remove the transmitter battery before performing this inspection.
The waveform is similar to that shown in the illustration
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
A
B
C
Replace the certification ECU (smart key ECU assembly) with a new one.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Register the ECU communication ID codes.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM>DTC CHECK / CLEAR
Before checking for DTCs, perform "DTC Output Confirmation Operation" procedure.
DTC B2784 is not output.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
A
B
C