Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY › 2016.10–2019.09
RM32K0E _52 Drivetrain _061224 DRIVE SHAFT / PROPELLER SHAFT _0299463 FRONT DRIVE SHAFT ASSEMBLY A

DRIVE SHAFT / PROPELLER SHAFT  FRONT DRIVE SHAFT ASSEMBLY  DISASSEMBLY  


PROCEDURE

Hide 43448G 1.SEPARATE FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP

a.

Secure the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.
C108564

Using pliers, separate the front No. 2 axle inboard joint boot clamp.


Hide 43448F 2.SEPARATE FRONT AXLE INBOARD JOINT BOOT CLAMP

a.

Separate the front axle inboard joint boot clamp.

HINT:

Perform the same procedure as for the front No. 2 axle inboard joint boot clamp.



Hide 3.SEPARATE FRONT AXLE INBOARD JOINT BOOT

a.

Separate the front axle inboard joint boot from the front drive inboard joint assembly.


Hide 4.REMOVE FRONT DRIVE INBOARD JOINT ASSEMBLY

a.

Remove the old grease from the front drive inboard joint assembly.


b.
F045461C08
1.99,0.646 1.99,0.25 1.99,0.25 1.198,0.25 false 1.677,0.938 1.677,0.25 false 1.01,0.146 1.177,0.292 0.167,0.146 10 false *a
*a Matchmark


Put matchmarks on the front drive inboard joint assembly and front drive outboard joint shaft assembly.

NOTICE:

Do not use a punch for the marks.



c.

Remove the front drive inboard joint assembly from the front drive outboard joint shaft assembly.

NOTICE:
·

Be careful when removing the front drive inboard joint assembly from the front drive outboard joint shaft assembly as the rollers of the tripod joint may fall out.

·

Do not drop the rollers of the tripod joint.




d.
C348430

Remove the 3 rollers from the tripod joint.


e.

Secure the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



f.
C348431

Using a snap ring expander, remove the front drive inner shaft inner shaft snap ring from the front drive outboard joint shaft assembly.


g.
C348432C02
2.833,1 1.74,1.667 1.74,1.667 2.875,1.104 true 1.573,1.583 1.885,1.74 0.313,0.156 10 false *a
*a Matchmark


Put matchmarks on the front drive outboard joint shaft assembly and tripod joint.

NOTICE:

Do not use a punch for the marks.



h.

Using a brass bar and a hammer, tap out the tripod joint from the front drive outboard joint shaft assembly.

NOTICE:
·

Do not tap the areas where the rollers contact the tripod joint.

·

Do not drop the tripod joint.




Hide 5.REMOVE FRONT AXLE INBOARD JOINT BOOT

a.

Remove the front No. 2 axle inboard joint boot clamp, front axle inboard joint boot and front axle inboard joint boot clamp.


Hide 43474E 6.REMOVE FRONT DRIVE SHAFT DAMPER LH

a.
C310867

Using needle-nose pliers, separate the 2 front drive shaft damper clamps.


b.

Remove the front drive shaft damper and 2 front drive shaft damper clamps from the front drive outboard joint shaft assembly.


Hide 43474D 7.REMOVE FRONT DRIVE SHAFT DAMPER RH

HINT:

Perform the same procedure as for the LH side.


Hide 43447F 8.SEPARATE FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP (for LH Side)

a.
C282245

Using pliers, separate the front No. 2 axle outboard joint boot clamp as shown in the illustration.


Hide 43447E 9.SEPARATE FRONT AXLE OUTBOARD JOINT BOOT CLAMP (for LH Side)

a.

Separate the front axle outboard joint boot clamp.

HINT:

Perform the same procedure as for the front No. 2 axle outboard joint boot clamp.



Hide 10.REMOVE FRONT AXLE OUTBOARD JOINT BOOT (for LH Side)

a.

Remove the front axle outboard joint boot clamp, front axle outboard joint boot and front No. 2 axle outboard joint boot clamp from the front drive outboard joint shaft assembly.


b.

Remove the old grease from the front drive outboard joint shaft assembly.


Hide 41336E 11.REMOVE FRONT DRIVE SHAFT DUST COVER LH

HINT:

Only perform the following procedure if the front drive shaft dust cover LH is deformed.


a.
C235586E01
1.885,1.448 2.698,1.688 true 2.74,1.615 3.198,1.813 0.458,0.198 10 false SST

Using SST and a press, remove the front drive shaft dust cover LH.

SST
09950-00020  

NOTICE:
·

Be careful not to drop the front drive inboard joint assembly.

·

Do not overtighten SST.




Hide 41336D 12.REMOVE FRONT DRIVE SHAFT DUST COVER RH

HINT:

Only perform the following procedure if the front drive shaft dust cover is deformed.


a.

Perform the same procedure as for the LH side.