Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE PEDAL (for LHD) › 2016.10–2019.09
RM32K0E _54 Brake _060045 BRAKE SYSTEM (OTHER) _0299581 BRAKE PEDAL(for LHD) N

BRAKE SYSTEM (OTHER)  BRAKE PEDAL(for LHD)  ADJUSTMENT  


PROCEDURE

Hide 1.INSPECT AND ADJUST BRAKE PEDAL HEIGHT

a.

Remove the No. 1 air duct.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL


b.

Check the brake pedal height.

NOTICE:
·

Inspect and adjust the brake pedal height with the floor carpet folded back.

·

When performing the measurement, make sure that the measuring device is contacting the surface of the dash panel insulator assembly clip.



i.

Measure the shortest distance between the brake pedal pad surface and dash panel insulator assembly clip.

C366608C01
2.042,1.667 2.042,2 true 2.99,2.375 2.823,2.542 2.823,2.542 2.656,2.542 true 6.021,0.927 5.854,0.927 5.854,0.927 5.604,1.177 true 5.25,2.583 5.417,2.583 5.417,2.583 5.573,2.396 true 1.948,2.031 2.146,2.219 0.198,0.188 10 true *1 3.729,1.781 3.906,1.969 0.177,0.188 10 true *a 2.438,2.417 2.615,2.604 0.177,0.188 10 true *2 5.688,1.708 5.865,1.896 0.177,0.188 10 false *a 6.073,0.813 6.271,1 0.198,0.188 10 true *1 5.031,2.469 5.208,2.656 0.177,0.188 10 true *2
*1 Brake Pedal Pad *2 Dash Panel Insulator Assembly Clip
*a Brake Pedal Height - -


Brake Pedal Height from Dash Panel Insulator Assembly Clip:

173.5 to 185.5 mm (6.83 to 7.30 in.)


If the pedal height is not as specified, adjust the brake pedal height according to the procedure below.



c.

Adjust the brake pedal height.

i.
C366609C01
1.479,1.51 1.479,2.094 1.479,2.094 1.313,2.094 false 2.135,1 2.469,1 false 1.896,3.844 1.646,4.177 1.646,4.177 1.479,4.177 true 2.5,0.906 2.813,1.063 0.313,0.156 10 false *1 1.104,2 1.417,2.156 0.313,0.156 10 false *2 2.646,3.667 2.958,3.823 0.313,0.156 10 false *a 1.271,4.083 1.583,4.24 0.313,0.156 10 false *3
*1 Stop Light Switch Assembly
*2 Clevis Lock Nut
*3 Dash Panel Insulator Assembly Clip
*a Brake Pedal Height


Remove the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL


ii.

Loosen the clevis lock nut.


iii.

Adjust the brake pedal height by turning the push rod.

Brake Pedal Height from Dash Panel Insulator Assembly Clip:

173.5 to 185.5 mm (6.83 to 7.30 in.)



iv.

Tighten the clevis lock nut.

Torque:
25.5 N*m (260 kgf*cm, 19 ft.*lbf)


v.

Install the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION



d.

Hide 89510D 2.INSPECT AND ADJUST BRAKE PEDAL STROKE SENSOR ASSEMBLY

a.

Inspect the brake pedal stroke sensor assembly.

i.

Connect the GTS to the DLC3 with the power switch off.


ii.

Turn the power switch on (IG).


iii.

Turn the GTS on and enter the following menus: Chassis / ABS/VSC/TRC / Data List / Stroke Sensor.

Chassis > ABS/VSC/TRC > Data List
Tester Display
Stroke Sensor
50003 105 11

iv.

Read the stroke sensor value without the brake pedal depressed.

Standard Voltage (without the brake pedal depressed):

0.8 to 1.2 V


If the stroke sensor value is not within the standard voltage, adjust the brake pedal stroke sensor assembly.



b.

Adjust the brake pedal stroke sensor assembly.

i.

Remove the No. 1 air duct.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL


ii.
C366610

Loosen the 2 nuts.

NOTICE:

Do not depress the brake pedal after turning the power switch on (IG).



iii.
C366611

Read the stroke sensor value in the Data List, and turn the brake pedal stroke sensor assembly slowly to the right or left to adjust the output voltage so that it is within the following range.

Standard Voltage (without the brake pedal depressed):

0.8 to 1.2 V



iv.

Tighten the 2 nuts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


v.

Perform linear solenoid valve offset learning, ABS holding solenoid valve learning, brake pedal stroke sensor assembly zero point calibration and system information memorization.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>CALIBRATION


vi.

Turn the GTS off and turn the power switch off.


vii.

Disconnect the GTS.


viii.


Hide 3.INSPECT BRAKE PEDAL FREE PLAY

a.
C132708C04
2.177,1.542 2.781,1.885 0.604,0.344 10 *a
*a Brake Pedal Free Play


Depress the brake pedal until a slight resistance is felt. Measure the brake pedal free play as shown in the illustration.

Brake Pedal Free Play:

1.0 to 6.0 mm (0.0394 to 0.236 in.)


If the pedal free play is not as specified, check the stop light switch clearance.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION

If the pedal free play is as specified, proceed to the Inspect Brake Pedal Reserve Distance procedure.


Hide 4.INSPECT BRAKE PEDAL RESERVE DISTANCE

a.

With the power switch on (READY), depress the brake pedal and measure the brake pedal reserve distance.

C368081C01
2.042,1.823 2.042,1.479 true 5.594,2.229 5.938,2.031 false 5.115,2.344 5.458,2.146 true 3.771,1.615 4.01,1.823 0.24,0.208 10 true *a 0.917,1.073 1.146,1.281 0.229,0.208 10 true *c 4.917,2.302 5.229,2.458 0.313,0.156 10 false *d 1.979,1.896 2.188,2.115 0.208,0.219 10 true *1 6,1.938 6.313,2.094 0.313,0.156 10 false *b
*1 Brake Pedal Pad - -
*a Brake Pedal Reserve Distance *b Floor Panel
*c 30 mm (1.18 in.) *d Line Extended from Floor Panel Surface


Brake Pedal Reserve Distance from Line Extended from Floor Panel Surface at 300 N (31 kgf, 67.4 lbf):

119.0 mm (4.69 in.) or more


If the distance is not as specified, troubleshoot the brake system.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE