Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER PUMP(for LHD)
RM32K0E _54 Brake _060045 BRAKE SYSTEM (OTHER) _0299585 BRAKE BOOSTER PUMP(for LHD) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER PUMP(for LHD)  INSTALLATION  


PROCEDURE

Hide 47381 1.INSTALL NO. 1 BRAKE TUBE CLAMP BRACKET

a.

Install the No. 1 brake tube clamp bracket to the brake booster pump assembly with the bolt.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


Hide 44571A 2.INSTALL NO. 1 BRAKE ACTUATOR HOSE

a.
C347163C01
2.792,1.677 2.792,1.396 true 2.229,1.688 2.438,1.688 2.438,1.688 2.438,1.417 true 2.083,1.615 2.281,1.792 0.198,0.177 10 false *a 2.729,1.688 2.927,1.854 0.198,0.167 10 false *b 1.708,2.188 2.167,2.385 0.458,0.198 10 false 90° 1.708,2.948 2.167,3.146 0.458,0.198 10 false 90°
*a Alignment Mark
*b Rib of Brake Booster Pump Assembly Port
V100136

Front of the vehicle


Install the No. 1 brake actuator hose to the brake booster pump assembly, and slide the clip to secure it.

NOTICE:
·

When installing the No. 1 brake actuator hose, make sure to align its alignment mark with the rib of the brake booster pump assembly.

·

Install the clip within the range shown in the illustration.




Hide 47070 3.INSTALL BRAKE BOOSTER PUMP ASSEMBLY

a.
C347165

Install the brake actuator case collar and brake booster pump bushing to the brake actuator bracket assembly.


b.

Temporarily install the brake actuator bracket assembly to the vehicle body.

NOTICE:

Do not apply excessive force to the brake lines or refrigerant lines.



c.

Temporarily install the brake booster pump assembly as shown in the illustration.

C366957C01
3.729,3.26 4.094,2.719 4.094,2.719 4.26,2.719 false 4.469,3.208 4.688,2.906 4.688,2.906 4.854,2.906 false 2.365,3.438 2.531,3.438 2.531,3.438 2.677,3.198 false 3.406,3.604 3.573,3.604 3.573,3.604 3.688,3.448 false 2.156,3.333 2.469,3.49 0.313,0.156 10 false *1 4.906,2.802 5.219,2.958 0.313,0.156 10 false *2 3.219,3.5 3.531,3.656 0.313,0.156 10 false *3 4.313,2.615 4.625,2.771 0.313,0.156 10 false *4
*1 Union *2 Connector
*3 Wire Harness *4 Stud
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


NOTICE:
·

Do not apply excessive force to the brake lines or refrigerant lines.

·

Do not drop the brake booster pump assembly when carrying it.

·

Be careful not to allow brake fluid to enter the connector.

·

If installing a new brake booster pump assembly, do not remove the hole plugs before connecting the brake lines because the brake booster pump assembly is filled with brake fluid.

·

Do not carry the brake booster pump assembly by the parts shown in the illustration.



HINT:
·

Move the brake actuator bracket assembly as necessary to allow the brake booster pump assembly to be temporarily installed.

·

Make sure to only temporarily install the brake booster pump assembly as the brake actuator assembly needs to be installed first.




d.

Install the brake actuator bracket assembly with the bolt.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


e.
C347159N01
0.844,1.083 0.979,1.271 0.135,0.188 10 true 1 2.313,1.573 2.448,1.76 0.135,0.188 10 true 2

Install the 2 nuts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)

NOTICE:

Tighten the nuts in the order shown in the illustration.



f.

Engage the clamp to install the No. 3 front brake tube to the brake actuator bracket assembly.


Hide 473A1 4.INSTALL ACCUMULATOR TO BRAKE MASTER CYLINDER TUBE

a.
C366958C01
0.448,0.26 0.854,0.417 true 0.24,0.167 0.552,0.323 0.313,0.156 10 false *a
*a Clamp Cover


Engage the 6 clamps to install a new No. 1 brake tube clamp to the accumulator to brake master cylinder tube and brake lines.

NOTICE:

Do not kink or damage the brake lines.



b.

Engage the clamp to install a new No. 2 brake tube clamp to the vehicle body.


c.

Engage the 6 clamps to install the No. 2 brake tube clmap to the accumulator to brake master cylinder tube and brake lines.

NOTICE:

Do not kink or damage the brake lines.



d.

Engage the claw to install the clamp cover.


e.

Engage the 6 clamps to install a new No. 1 brake tube clamp to the accumulator to brake master cylinder tube and brake lines.

NOTICE:

Do not kink or damage the brake lines.



f.
C366959C01
1.74,2.844 2.052,3 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Using a union nut wrench, connect the accumulator to brake master cylinder tube to the brake booster with master cylinder assembly.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not kink or damage the accumulator to brake master cylinder tube.

·

Do not allow the accumulator to brake master cylinder tube to twist or interfere with other parts or the vehicle body during tightening.

·

Do not allow any foreign matter such as dirt or dust to enter the accumulator to brake master cylinder tube from the connecting parts.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)




Hide 44551C 5.INSTALL NO. 1 BRAKE ACTUATOR TUBE

a.

Install the No. 1 brake actuator tube with the 2 nuts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)