Use the same procedure for RHD and LHD vehicles.
The following procedure is for the LHD vehicles.
1. PRECAUTION
Make sure to perform initialization after replacing the air conditioning radiator damper servo sub-assembly. If initialization is not performed, the air conditioner unit assembly will not perform properly as the air conditioning amplifier assembly will not be able to recognize the position of the air conditioning radiator damper sub-assembly.
87211A
2.REMOVE NO. 2 AIR DUCT (for LHD)
Remove the screw.
Disengage the claws to remove the No. 2 airduct.
87211
3.REMOVE NO. 1 AIR DUCT (for RHD)
Remove the screw.
Disengage the claws to remove the No. 1 airduct.
88505
4.REMOVE AIR CONDITIONING DUCT SUB-ASSEMBLY
Disengage the claws to remove the air conditioning duct sub-assembly.
88482A
5.REMOVE COVER (w/o Rear Air Duct)
Disengage the claws to remove the cover.
82143
6.REMOVE NO. 3 INSTRUMENT PANEL WIRE (w/ PTC Heater)
Disconnect the 2 connectors.
Disengage the clamps to remove the No. 3 instrument panel wire.
87130D
7.REMOVE BLOWER ASSEMBLY
87114L
8.REMOVE NO. 2 HEATER COVER (w/ PTC Heater)
Remove the screw.
Disengage the claw and guide to remove the No. 2 heater cover.
87710G
9.REMOVE QUICK HEATER ASSEMBLY (w/ PTC Heater)
|
Remove in this Direction |
Disengage the guide to remove the quick heater assembly as shown in the illustration.
88650N
10.REMOVE AIR CONDITIONING AMPLIFIER ASSEMBLY
|
Remove in this Direction |
for LHD:
Disconnect the connector.
Remove the screw.
Disengage the guide to remove the air conditioning amplifier assembly as shown in the illustration.
|
Remove in this Direction |
for RHD:
Disconnect the connector.
Remove the screw.
Disengage the guide to remove the air conditioning amplifier assembly as shown in the illustration.
82210K
11.REMOVE AIR CONDITIONING HARNESS ASSEMBLY
Disconnect each connector.
Disengage clamps to remove the air conditioning harness assembly.
87114B
12.REMOVE HEATER COVER (w/o PTC Heater)
|
Remove in this Direction |
Remove the screw and heater cover as shown in the illustration.
88539J
13.REMOVE DRAIN COOLER HOSE
Remove the drain cooler hose.
87050C
14.REMOVE NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY
Remove the 3 screws and No. 1 air conditioning radiator damper servo sub-assembly.
88897M
15.REMOVE HEATER PIPE GROMMET
Remove the heater pipe grommet.
87124B
16.REMOVE HEATER CLAMP
Disengage the claws to remove the heater clamp.
87107A
17.REMOVE HEATER RADIATOR UNIT SUB-ASSEMBLY
|
Remove in this Direction |
Remove the heater radiator unit sub-assembly as shown in the illustration.
Prepare a drain pan or cloth in case the coolant leaks.
88515
18.REMOVE COOLER EXPANSION VALVE
Remove the grommet.
Using a 4 mm hexagon socket wrench, remove the 2 hexagon bolts and cooler expansion valve.
Remove the 2 O-rings from the No. 1 cooler evaporator sub-assembly.
88501
19.REMOVE NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY
Remove the 2 screws.
Disengage the claws to remove the upper heater case with No. 1 cooler evaporator sub-assembly from the lower heater case.
Disengage the clamp.
Remove the No. 1 cooler evaporator sub-assembly with No. 1 cooler thermistor from the upper heater case.
88625
20.REMOVE NO. 1 COOLER THERMISTOR