Home › Brake › BRAKE (REAR) › REAR BRAKE › 2016.10–2018.05
RM32K0E _54 Brake _060047 BRAKE (REAR) _0300500 REAR BRAKE A

BRAKE (REAR)  REAR BRAKE  REASSEMBLY  


PROCEDURE

Hide 1.TEMPORARILY TIGHTEN REAR DISC BRAKE BLEEDER PLUG

a.

Temporarily install the rear disc brake bleeder plug to the rear disc brake cylinder assembly.

HINT:

Fully tighten the rear disc brake bleeder plug after bleeding the system.



Hide 31478C 2.INSTALL REAR DISC BRAKE BLEEDER PLUG CAP

a.

Install the rear disc brake bleeder pug cap to the rear disc brake bleeder plug.


Hide 3.INSTALL PISTON SEAL

a.
C318785C02
0,0 0,0 false
V100155

Lithium Soap Base Glycol Grease


Apply lithium soap base glycol grease to the entire circumference of a new piston seal.


b.

Install the piston seal to the rear disc brake cylinder assembly.

NOTICE:
·

Do not damage the inner surface or piston seal groove of the rear disc brake cylinder.

·

Do not allow the nut to rotate. If the nut is accidentally allowed to rotate, return it to its original position.




Hide 4.INSTALL REAR DISC BRAKE PISTON

a.
C335019C01
2.344,0.49 2.708,0.49 false 2.135,1.573 2.5,1.573 false 2.771,0.427 3.083,0.583 0.313,0.156 10 false *1 2.552,1.51 2.865,1.667 0.313,0.156 10 false *2
*1 Cylinder Boot
*2 Rear Disc Brake Piston
V100155

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the entire circumference of a new cylinder boot.


b.

Apply a light layer of lithium soap base glycol grease to the contact surfaces of the rear disc brake piston.


c.
C367998C01
0.906,0.104 1.219,0.26 0.313,0.156 10 false *a 0.917,1.135 1.229,1.292 0.313,0.156 10 false *b
*a Front Side
*b Back Side


Install the cylinder boot to the rear disc brake piston.

NOTICE:

The front and back sides of the cylinder boot are different. Make sure not to install the cylinder boot backwards.



d.
C335021C01
0.625,0.833 1.229,0.323 1.229,0.323 1.063,0.823 true 0.625,1.365 1.219,1.188 1.219,1.188 1.063,1.354 true 1.281,0.219 1.594,0.375 0.313,0.156 10 false *a 1.281,1.104 1.438,1.302 0.156,0.198 10 false A
*a Indentations


Install the rear disc brake piston to the rear disc brake cylinder assembly.

NOTICE:
·

Install the rear disc brake cylinder LH so that its portions marked (A) fit into the indentations of the rear disc brake piston.

·

Do not forcibly install the rear disc brake piston into the rear disc brake cylinder assembly.




e.
C318787C01
1.26,0.958 1.458,0.667 1.458,0.667 1.729,0.667 true 0.521,2.167 0.521,1.573 true 0.604,0.906 0.74,0.906 0.74,0.906 0.813,1.063 false 0.417,0.844 0.729,1 0.313,0.156 10 false *1 0.469,2.198 0.781,2.354 0.313,0.156 10 false *2 1.781,0.604 2.094,0.76 0.313,0.156 10 false *3
*1 Cylinder Boot
*2 Rear Disc Brake Cylinder Assembly
*3 Rear Disc Brake Piston


Install the cylinder boot to the rear disc brake cylinder assembly as shown in the illustration.

NOTICE:
·

Do not damage the cylinder boot.

·

Securely install the cylinder boot into the groove of the rear disc brake cylinder assembly and groove of the rear disc brake piston.